···
Log in / Register

What are the road sections where motor vehicles are prohibited from parking within 50 meters?

4 Answers
AuroraAnn
07/29/25 10:20pm
Motor vehicles are prohibited from parking at intersections, railway crossings, sharp curves, narrow roads less than 4 meters wide, bridges, steep slopes, tunnels, and within 50 meters of these locations. When temporarily parking on the road, motor vehicles must comply with the following regulations: 1. Parking is prohibited in sections with no-parking signs or markings, in sections with separation facilities between motor vehicle lanes and non-motor vehicle lanes or sidewalks, as well as at crosswalks and construction zones; 2. Parking is prohibited in front of bus stops, emergency stations, gas stations, fire hydrants or fire stations, and within 30 meters of these locations, except when using these facilities.
Was this review help?
9
5
Share
LeEvan
08/15/25 10:54pm
Once I was looking for a parking spot in the city and absentmindedly parked right next to a traffic light intersection. When I returned, I found a ticket on my windshield. After checking, I learned that traffic regulations are quite strict—no parking is allowed within 50 meters of areas like intersections, sharp curves, bridges, steep slopes, and tunnel entrances. This is primarily for safety reasons. If you park near an intersection, it can block drivers' sightlines, making it hard to see oncoming traffic when turning, which could easily lead to collisions with pedestrians or other vehicles. Moreover, these areas have frequent traffic flow, and parking there can cause congestion or increase accident risks. Now I’ve developed a habit of estimating the distance before parking—50 meters is roughly one-third the width of a football field. I count my steps while walking to confirm the distance. Safety comes first; avoiding fines is minor compared to protecting lives—both your own and others’. I recommend everyone pay close attention to no-parking signs on the road.
Was this review help?
12
0
Share
Expand All
LaEverett
10/18/25 2:21am
From a road safety perspective, 50-meter no-parking zones are commonly found near intersections, sharp curves, bridges, steep slopes, and tunnel entrances. These sections are designed with visibility and traffic flow in mind, and parking within them can create visual blind spots. For example, parking on a steep slope may lead to rear-end collisions by following vehicles, posing significant risks. I always pay close attention to these rules while driving, not just because violations incur fines of several hundred yuan, but more importantly out of a sense of responsibility toward others. Expanding on this, similar restrictions apply in areas like school or hospital entrances, but the 50-meter standard covers the primary risk points. It's advisable to glance around for yellow or red no-parking lines or signs before parking in unfamiliar areas. Adhering to these rules helps maintain smoother traffic flow and reduces accidents. By working together, we can create a safer travel environment for everyone.
Was this review help?
10
5
Share
Expand All
VanMia
12/01/25 3:01am
When I first started learning to drive, my instructor reminded me that there are many places where parking is prohibited within 50 meters, such as intersections, sharp turns, both ends of bridges, the bottom of steep slopes, and near tunnel entrances. He explained that all these rules are for safety reasons, to avoid obstructing visibility or causing accidents. Later, I developed the habit of checking distances while driving. Fifty meters is roughly the distance covered in 20 steps, making it easy to estimate. If you're parking near these sensitive areas, it's better to find another spot to avoid trouble. Safety comes first—don't underestimate these rules.
Was this review help?
12
1
Share
Expand All
More Forum Discussions

Where is Jetour Cars Produced?

Jetour cars are manufactured at the Chery Intelligent Manufacturing Base in Kaifeng, Henan. Here is some information about Jetour cars: 1. Jetour is a car product series launched by Chery Holding Group on January 22, 2018. All Jetour models are SUVs. The models under Jetour include X70, X70S, X90, X95, etc. 2. Jetour SUVs offer relatively high cost performance, making them suitable for young people who have just started working and do not have much money. SUVs are also favored by many consumers due to their spacious interiors, excellent driving visibility, and high ground clearance for better off-road capability. SUVs are versatile, offering great comfort, large trunk space, and the ability to carry a lot of cargo. Because of their high ground clearance, many people who enjoy self-driving tours prefer SUVs for their better off-road performance. 3. There are also many 7-seater SUV models on the market, which add a third row of seats, allowing the vehicle to accommodate seven people at the same time.
6
5
Share

What Causes Unstable Idling in a New Car?

New car unstable idling reasons are as follows: Air filter: If the air filter is not replaced in time, it will cause insufficient air intake and reduce engine idle speed. Abnormal water temperature: High engine water temperature will cause early ignition timing, change the air-fuel mixture ratio, and thin the engine oil viscosity (poor lubrication). Causes of abnormal water temperature include: insufficient coolant, thermostat not opening, fan failure, and inaccurate temperature control switch. Excessive carbon buildup in throttle body and air flow meter: The throttle body and air flow meter are prone to dirt. Most modern cars use electronic throttle bodies, and even slight carbon buildup can affect them. Excessive carbon buildup in the throttle body can cause throttle sticking, severe power loss, and unstable idling. Clogged fuel injectors: Clogged fuel injectors will result in inconsistent fuel injection amounts, causing uneven cylinder operation and leading to unstable ignition and idling.
18
2
Share

How to Disassemble the LaCrosse Radiator?

Disassembling the LaCrosse radiator requires eight steps, as follows: 1. Remove the wiring harness clip inside the upper crossbeam of the radiator and move the wiring harness aside. 2. Remove the air filter assembly and move the control computer aside. 3. Remove the right headlight. 4. Remove the fan frame assembly. 5. Unscrew the drain bolt at the bottom of the radiator and collect the coolant. 6. Remove the upper and lower hoses. 7. Remove the radiator's mounting bolts. 8. Remove the radiator at a certain angle. The LaCrosse was introduced to replace the Regal and secure a significant position in the domestic mid-to-high-end car market. It integrates General Motors' globally synchronized advanced platform, superior resources from both domestic and international markets, and independent research and development. Equipped with cutting-edge leading powertrains and top-tier safety technology, it delivers an exhilarating driving experience. Luxurious features and meticulous craftsmanship provide an ultimate, comfortable, and opulent riding experience.
2
5
Share

What type of vehicle is the VV5?

VV5 is a compact SUV. Here are the relevant details about the VV5: 1. The dimensions of the VV5 are: length 4462mm, width 1857mm, height 1638mm, with a wheelbase of 2680mm, a fuel tank capacity of 55 liters, and a curb weight of 1579kg. 2. The WEY VV5 is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 171PS, a maximum power of 126kW, and a maximum torque of 287Nm, paired with a 7-speed dual-clutch transmission. 3. The VV5 is a model under the WEY brand. Other WEY models include: WEY VV7, WEY VV6, WEY VV7 GT, WEY P8, WEY VV7 New Energy, etc.
19
3
Share

How to reset the wrench light on Bestune X40?

Bestune X40 wrench light can be cleared by following these steps: 1. Turn off the ignition switch; 2. Press and hold both arrow buttons simultaneously, then turn on the ignition switch; 3. After approximately 3 seconds with the ignition on, release both arrow buttons; 4. The maintenance menu will appear on the display, asking whether to reset the maintenance reminder; 5. Press and hold the SET (reset) button for more than 3 seconds; 6. Press the MODE button; 7. Turn off the ignition switch and restart the vehicle to complete the maintenance light reset. Here is relevant information about the wrench light: 1. The wrench symbol on the dashboard is the vehicle's maintenance reminder light. If illuminated, it indicates that the vehicle requires maintenance. Regular maintenance can improve vehicle performance and extend its service life. 2. According to relevant vehicle maintenance test programs, proper maintenance can save 11.36% of fuel during driving; after complete maintenance, CO emissions during idle driving are reduced by 45.37%.
16
1
Share

Will tightening the valve stem press against the valve core?

Tightening the valve stem can press against the valve core, but the tire won't leak air even if the valve core cap is missing, because the valve stem is what actually functions. As long as the valve stem isn't damaged, there will be no air leakage. Types of valve stems: The Schrader valve (American-style) is the most widely used type of valve stem, commonly found in cars, motorcycles, bicycles, and other vehicles. The Presta valve (French-style) is typically used on bicycles, especially road bikes, along with other special types of valve stems. Functions of valve stems: The valve stem functions as a small component for inflating and deflating tires, maintaining the seal after inflation. A standard valve stem consists of three main parts: the valve stem body, the valve core, and the valve stem cap.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.