···
Log in / Register

What are the repair methods for a generator not generating electricity?

1Answers
LaJayce
07/28/2025, 04:52:09 AM

Generator not generating electricity repair methods are: 1. If the generator belt is broken or slipping, tighten the adjustment device or replace the belt; 2. Check for open circuits in the generator output wires and inspect wire condition; 3. If the rotor part is stuck, manually test whether it rotates smoothly; 4. If the winding is damaged, use a multimeter to measure the coil resistance to see if it is normal. If there is no resistance value, the coil must be rewound or the motor replaced. The car generator is the main power source of the vehicle. Its function is to supply power to all electrical devices (except the starter) when the engine is running normally (above idle speed), while also charging the battery.

Was this review help?
111
Share
More Q&A

Is a Door Waterproof Membrane Absolutely Necessary?

Door waterproof membranes are not absolutely necessary, and the decision to purchase and use them can be based on actual conditions. The functions of a door waterproof membrane: It can block external moisture, preventing rainwater or water vapor from entering the vehicle interior. Waterproof breathable membrane: It is a new type of polymer waterproof material. In terms of manufacturing process, the technical requirements for waterproof breathable membranes are much higher than those for ordinary waterproof materials. At the same time, in terms of quality, waterproof breathable membranes also possess functional characteristics that other waterproof materials lack. After multiple layers of anti-reflective coating are applied to the lens surface, the lens becomes particularly prone to stains, which can damage the anti-reflective effect of the coating.
108
Share

Can Vehicle Insurance Be Suspended During Non-Use?

Vehicle insurance can be extended during periods of non-use. If a car will not be driven temporarily, it's best to first complete the suspension procedures at the vehicle management department. This will normally postpone the annual inspection without any negative impact. Otherwise, it may affect the vehicle and vessel tax included in the compulsory traffic insurance. Important Notes: For vehicle insurance, commercial insurance can be fully canceled, while compulsory traffic insurance cannot be canceled for vehicle deregistration or theft cases. However, the insurance period of compulsory traffic insurance can be extended. Procedure: If the proper procedures are followed, there will be no negative consequences. Failure to complete the suspension procedures at the vehicle management department may result in missed inspections, which could lead to penalties or even vehicle deregistration. If suspension procedures aren't completed and neither insurance nor vehicle and vessel tax is paid, the owner will be required to pay the previous year's vehicle and vessel tax when purchasing insurance the following year.
118
Share

What are the reasons for no sound in car music?

Car music has no sound for the following reasons: Volume not turned on: The volume on the car navigation system or mobile phone is not turned on, simply turn it on. Incorrect phone audio settings: Some mobile phones' music playback programming is incompatible with certain car models' connection codes, so only phone calls can be heard but not music. It may be necessary to change the Bluetooth playback frequency band, etc. Multimedia music not enabled: It could also be that the multimedia music function of the car Bluetooth is not turned on, which needs to be set and enabled. Signal interference: Or the media audio on the phone is not turned off, causing signal interference with the Bluetooth function.
108
Share

What kind of adhesive is used for door waterproof membranes?

There are four types of adhesives used for door waterproof membranes: Acrylic double-sided pressure-sensitive tape: When using it, hold the tape roll and roll it along the perimeter of the inner door panel to adhere the pressure-sensitive tape to the door. Then, attach the waterproof membrane to the tape. However, the bonding strength of pressure-sensitive tape is limited, and it becomes very weak when the bonding surface has dust or oil stains. Butyl tape: Apply the tape along the perimeter of the door, then press the edges of the waterproof film onto the tape to create a strong bond between them. However, the bonding strength is limited, and it becomes very weak when the bonding surface has dust or oil stains. Water-based pressure-sensitive adhesive: It can be directly screen-printed onto the film. Its advantage is that it is particularly suitable for waterproof films with complex shapes, and the water-based adhesive is environmentally friendly. Hot melt adhesive: The adhesive can be applied directly to the film or to the inner door panel. This method has fast curing speed, is easy to operate, and is suitable for rapid automated production.
102
Share

What is the flashing frequency of turn signals?

The flashing frequency of turn signals is approximately once per second. Reason for flashing once per second: When the turn signal clicks three times, it corresponds to 3 seconds in duration. This is because the normal flashing frequency of the turn signal relay is approximately 1 Hz, which equates to 60 flashes per minute, or about one flash per second. Reasons for abnormal turn signal flashing: Turn signals serve as warning indicators during turns, alerting surrounding vehicles of the intended direction change. Typically, turn signals and hazard warning lights share the same bulb. If the flashing frequency suddenly increases, it may indicate a malfunction in one side of the turn signal or its circuit.
104
Share

How many seconds should the turn signal be on?

The turn signal should be on for at least 3 seconds or more, and there is no time limit for its use. Reasons for at least 3 seconds: Traffic regulations have clearly stipulated that the turn signal must be on for at least three seconds when turning, and violators will be fined. Turn signal flashing frequency: The turn signal sounds 3 times, which is equivalent to 3 seconds in time, because the normal flashing frequency of the turn signal relay is about 1 Hz, which is 60 times per minute, and the turn signal flashes about once per second. Turn signal: It is an important indicator light that is turned on when a motor vehicle turns to alert vehicles and pedestrians around. The turn signal tube uses a xenon tube, controlled by a single-chip microcomputer circuit, with left and right alternating flashes working continuously.
111
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.