What are the regulations for using temporary vehicle license plates?

2 Answers
DeJordan
07/29/25 4:22am
Temporary vehicle license plate usage regulations: 1. Validity period: Temporary plates have a limited validity period, not exceeding 30 days at maximum. For new vehicles, the validity period cannot exceed 15 days. Therefore, vehicle owners must apply for formal license plates from the vehicle management authority within this period; 2. Regional restrictions: If it's a local temporary plate, it can only be used within the local area. The paper motor vehicle license plate that permits temporary road use of motor vehicles, also known as a temporary driving license plate, refers to the temporary vehicle driving certificate issued by the public security vehicle management department to vehicle owners before the new vehicle is officially registered.
Was this review help?
13
2
Share
LeSarah
08/12/25 8:06am
I remember when I first bought my new car, the temporary license plate had me a bit flustered. Typically, it's only valid for 15 to 30 days and must be prominently displayed on the lower right corner of the front windshield and the lower left corner of the rear windshield—make sure it doesn't come loose or get hidden. Don't drive beyond the permitted areas; local trips with a new car are fine, but crossing provinces might get you stopped. Always carry the car purchase invoice and insurance proof—I once forgot them and got questioned by the police for a long time. Once the validity period expires, swap it for a permanent plate immediately—no delays. New car owners often make these mistakes, so during the temporary plate transition, safety comes first—double-check the placement and documents. By the way, used car transfers might also use temporary plates, with the same rules applying. For short daily trips, ensure your lights and signals are working properly to avoid any mishaps.
Was this review help?
11
0
Share
Expand All
More Forum Discussions

Where is the car seat heating switch located?

The car seat heating switch is located in front of the gear shift lever on the center console panel, where you can see the heating indicator. Here is some related information: Seat Heating: The car seat heating feature is represented by a seat-like symbol with three horizontal lines next to it, typically offering high, medium, and low heating levels to choose from. The seat heating function involves an electric heating device installed inside the seat, controlled by the heating switch to turn the heating power on or off. When activated, the seat cushion generates heat to provide warmth. This feature is commonly found in cars with leather seats, as leather surfaces tend to be cold in winter. With this heating function, the seats become warm and comfortable.
6
2
Share

What are the alignment standards for left and right rearview mirrors when reversing into a parking space?

The left and right rearview mirrors should not extend beyond the dotted line when reversing into a parking space. Below is relevant information about rearview mirrors: 1. Function: Rearview mirrors are tools that allow drivers to directly obtain external information about the rear, sides, and lower parts of the car while seated in the driver's seat. For the convenience of the driver and to prevent traffic safety accidents and ensure personal safety, all countries mandate that cars must be equipped with rearview mirrors, and all rearview mirrors must be adjustable. 2. Classification: Rearview mirrors are categorized by installation location into external rearview mirrors, lower rearview mirrors, and internal rearview mirrors. By purpose, external rearview mirrors reflect the rear side of the car, lower rearview mirrors reflect the front lower part of the car, and internal rearview mirrors reflect the rear of the car and the interior situation.
3
0
Share

Will Transmission Fluid Expire If Not Changed for 5 Years?

Yes. If transmission fluid is not replaced within the recommended interval, its quality and performance will deteriorate, leading to increased impurities. This accelerates wear on transmission components, causing premature failures or higher failure rates. Below are additional details: 1. Primary functions of transmission fluid: Maintains cleanliness of the gear system while lubricating transmission components to extend their service life. 2. Replacement intervals: Manufacturers typically recommend changing transmission fluid every 2 years or 50,000 kilometers - whichever comes first. For example: • Vehicles used for 2 years but driven only 20,000+ kilometers • Vehicles used less than 1 year but already driven 50,000 kilometers Both scenarios require transmission fluid replacement. For new vehicles, first replacement at 50,000 km is advised. Subsequent intervals should adjust based on driving conditions: • Good road conditions: Replace every 70,000 km • Poor road conditions: Replace every 30,000-40,000 km This practice extends transmission lifespan and reduces failure rates.
12
4
Share

What Causes Reduced Engine Power in the Buick LaCrosse?

Buick LaCrosse engine power reduction is generally caused by a faulty throttle pedal sensor or loose connections. It requires inspection and replacement of the throttle pedal at a 4S shop. The accelerator pedal, also known as the throttle pedal, primarily controls the opening of the engine throttle valve, thereby regulating the engine's power output. Here is more detailed information: 1. Traditional Accelerator Pedal: Connected to the throttle valve via throttle cables or linkage rods. With the continuous advancement of automotive electronic technology, electronic throttles are increasingly widely used. When a driver presses the electronic throttle's accelerator pedal, it actually sends a throttle pedal position sensor signal to the engine ECU. 2. Electronic Throttle Pedal: As a key component of the electronic throttle control system, the performance of the electronic throttle pedal not only relates to multiple performance evaluation indicators of the car, such as power, comfort, and fuel economy, but also directly impacts driving safety. Any malfunction can affect the normal operation of the vehicle. If the electronic throttle pedal is damaged, the dashboard warning light will illuminate, the accelerator pedal may become stiff, produce unusual noises when pressed, and may even fail to return to its original position after being pressed, which is extremely dangerous.
4
3
Share

Reasons for a Sudden Increase in Car Fuel Consumption During Summer

The reasons for a sudden increase in car fuel consumption during summer are as follows: 1. Tire Pressure Issues: It is essential to regularly check whether the tires show signs of wear. Every vehicle comes with a label at the time of purchase, indicating the recommended tire pressure for both empty and fully loaded conditions. You can choose the appropriate pressure based on your specific situation because if the tire pressure is too low, the friction between the tires and the road increases, leading to a natural rise in fuel consumption. 2. Fully Open Windows: During summer, due to the hot weather, many people tend to use the air conditioning while driving, which can also increase fuel consumption. Some may opt to open all the windows to lower the temperature inside the car. However, the driving resistance caused by open windows can actually consume more energy than the air conditioning compressor. If driving at low speeds in urban areas, opening the windows might slightly reduce fuel consumption. But at medium to high speeds, accelerating with the windows open can result in significantly higher fuel consumption compared to using the air conditioning.
17
3
Share

Does Mis-shifting in Subject 3 Result in Deduction or Immediate Failure?

Mis-shifting in Subject 3 will only result in point deduction and not immediate failure. Here are some tips to avoid mis-shifting: 1. Gear Positions: Unfamiliarity with gear positions accounts for a significant portion of mis-shifting incidents. Specifically, gears 1, 3, and 5 are engaged by pushing forward from left to right, while gears 2 and 4 are engaged by pulling backward from left to right. Avoid looking down during gear shifts to prevent unnecessary mistakes. 2. First Gear: For example, to engage first gear, cover the gear knob with your palm, bring your fingers together, depress the clutch, pull the gear lever to the left, and then push it forward. This will successfully engage first gear. 3. Shifting to Second Gear: To shift to second gear, first depress the clutch, gently pull the gear lever back to neutral, and then pull it backward to engage second gear.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.