What are the reasons why the right rear door of a BMW cannot be opened?

1 Answers
Roberto
07/30/25 4:38am
There are several reasons why the right rear door of a BMW cannot be opened: Child lock is engaged: When closing the door, always check if the child lock is disengaged. If the door cannot be opened, use a flathead screwdriver to turn the child lock to the off position. Faulty lock cable: If this issue occurs, the door cannot be opened from inside the car because the faulty cable directly affects the lock mechanism. Deformed hinge or lock post: When the door is subjected to external force, it may cause deformation of the door hinge or lock post, which is also one of the reasons why the door cannot be opened. Faulty door limiter: When this problem occurs, opening the door becomes very difficult or impossible. The solution is to replace the door limiter with a new one, allowing the door to open and close smoothly.
Was this review help?
11
4
Share
More Forum Discussions

Why do the lights turn on when the car is submerged?

There may be water ingress in some plugs, causing electrical connections in the car. Below is relevant information about a submerged car: 1. Water level above the exhaust pipe: If the water only covers the exhaust pipe, promptly move the car away. Water in the exhaust pipe will not be sucked back into the engine, and engine stalling is primarily due to water entering the engine's intake system, unrelated to the exhaust pipe being submerged. 2. Water level at half-wheel height: If the water reaches half-wheel height, the car generally won't leak. However, if submerged for a prolonged period with aging seals, leaks may occur. In such cases, drive the car to a 4S shop, remove the interior, clean, and dry it. 3. Water level above half-wheel height: If the water exceeds half-wheel height, the engine may take in water, and the interior may leak. Do not start the engine to avoid damage to the engine or electronic components. Note that insurance will not cover damages caused by ignition in a submerged car.
9
1
Share

What are the precautions for vehicle damage assessment at a 4S shop?

Here are the precautions for vehicle damage assessment at a 4S shop: 1. Determine the repair method: Understand the insurance company's principles for assessing damaged parts. Generally, insurance companies prioritize repairing damaged parts if they can be restored to normal functionality. Only if the damaged parts cannot be repaired should they be replaced. Therefore, during the damage assessment, it is essential to clarify with both the insurance company and the repair facility which parts will be repaired and which will be replaced to avoid disputes later in the repair process. 2. Determine the vehicle repair cost: Disputes over repair costs are common. Insurance companies typically assess repair costs based on the repair facility's qualification level. For replacement parts, they quote prices according to the regional market rates for those components.
16
2
Share

Does Deep Road Water Affect the Car?

Deep road water can affect the car and may cause the engine to stall. On rainy days when road water is deep, the following precautions should be taken while driving: 1. Drive slowly and maintain a reasonable distance: Drive straight and at a low speed in the rain. Especially on highways, it is best to keep the speed below 30km/h and maintain a safe distance from the vehicle in front, avoiding large trucks. In heavy rain, try to keep a certain distance from the vehicle ahead, avoid following too closely, and refrain from frequent overtaking. 2. Maintain good visibility: In addition to cautious driving, promptly turn on the windshield wipers when driving in the rain. In dim weather, also turn on the low beams and fog lights. If there is frost on the front windshield, turn on the air conditioning and direct the cold air toward the windshield. If the rear windshield has frost, turn on the rear windshield heater to quickly eliminate the frost and avoid obstructing the view of vehicles behind. 3. How to handle wheel skidding: If the front wheels skid in the rain, steer in the opposite direction of the skid. If the rear wheels skid, steer in the same direction as the skid, never the opposite. At the same time, ensure the wipers are functioning properly to maintain clear visibility at all times.
7
4
Share

Where is the Car Bluetooth Switch?

The car Bluetooth switch is located in the lower right corner of the main interface. Here is an introduction to related content about car Bluetooth: 1. Programming: Some mobile phone music playback programming is incompatible with the pairing codes of certain car models, so only phone calls can be answered but music cannot be played. It may be necessary to change the Bluetooth playback frequency band, etc. 2. Multimedia Music: If the car Bluetooth's multimedia music is not enabled, it needs to be set up and turned on. 3. Media Audio: If the phone's media audio is not turned off, it may cause signal interference with the Bluetooth function. Below is additional extended information: 1. Bluetooth Technology: The Bluetooth technology in car Bluetooth systems is an extension of mobile phone Bluetooth technology. 2. Transmission System: They share the same transmission system. Car Bluetooth is simply an in-car wireless hands-free system designed and developed based on wireless Bluetooth technology.
7
3
Share

Why does the J6P have insufficient power without any fault codes?

J6P has insufficient power without any fault codes for the following reasons: 1. Abnormal fuel pressure: Low fuel pressure can damage the engine's lubrication conditions, leading to poor lubrication, cooling, and cleaning, which may cause adhesive wear on components. 2. Clutch slipping: Clutch slipping can result in power loss, increased likelihood of rolling back on slopes, weak driving performance, insufficient reverse traction, and accelerated wear on the clutch and flywheel. 3. Ignition circuit failure: This may be caused by faults in components such as the electronic igniter or ignition coil, or poor connections in the low-voltage circuit. Information about the J6P is as follows: 1. Model: The J6P is a truck under FAW Jiefang. 2. Displacement: 11.1T/12.5T/7.1T.
6
1
Share

Is a bulge on the tire serious?

Automobile tire bulges are serious and should be replaced promptly. The main causes of tire bulges are as follows: 1. Crown separation: Crown separation mainly manifests as delamination at the top of the tire tread (referred to as the crown surface). The primary reason is excessive tire pressure during use, which reduces the tire's contact area, leading to early wear. During operation, rolling acceleration or poor heat dissipation causes the tread temperature to rise. The adhesion between the cord layers decreases, and the increased centrifugal force on the tread causes crown delamination. 2. Shoulder separation: Shoulder separation is a type of sidewall bulge, divided into local and overall types, commonly found between the tire tread and sidewall. It mainly appears as noticeable bulges, resembling bubbles! Some may be ring-shaped, indicating complete separation! The sidewall and tire body are clearly detached. This is caused by insufficient drying of the cord during the tire manufacturing process before rubber coating, or excessive moisture content in the rubber itself, which is a quality issue.
14
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.