What Are the Reasons Why the Reversing Radar Does Not Alarm?

1 Answers
Ana
07/28/25 2:12pm
The reversing radar system's working power supply and grounding circuit not illuminating can cause this issue. Common fault points include a missing power supply to the reversing radar controller, a loose connection in the reversing radar probe plug, a damaged buzzer, or a loose connection in the buzzer plug. During troubleshooting, it is necessary to refer to the circuit diagram of the relevant vehicle model to locate the corresponding lines. Below is additional information about reversing radars: 1. Reversing Radar: The full name is "Reverse Anti-Collision Radar," also known as a "Parking Assistance Device." 2. Principle of Reversing Radar: It mainly consists of an ultrasonic sensor, controller, and display (or buzzer). When the gear lever is shifted into reverse, the reversing radar automatically starts working. When the radar detects that the distance to an obstacle behind the vehicle is too close, the buzzer or display device of the reversing radar will issue a warning to remind the driver to pay attention to the distance behind.
Was this review help?
8
2
Share
More Forum Discussions

What are the drawbacks of changing from 18-inch to 19-inch wheels?

Changing from 18-inch to 19-inch wheels has the following disadvantages: 1. Reduced shock absorption performance - larger wheels have relatively lower rolling resistance, leading to decreased shock absorption. 2. Increased road noise - larger wheels require more time to complete a full rotation, with increased friction surfaces resulting in louder noise. 3. Higher fuel consumption - changes in tire section width or aspect ratio will increase fuel consumption. 4. Degraded handling and driving experience - larger wheels raise the center of gravity, affecting vehicle balance and steering response, resulting in insufficient steering input, reduced steering angle, and heavier steering feel. 5. Increased load on the braking system - causing greater wear on brake pads.
14
1
Share

What to Do When the Battery of a Keyless Start Car Key Dies?

The solutions for a keyless start car key with a dead battery are: 1. Insert the smart key into the center console; 2. Insert the key blade inside the remote key into the keyhole; 3. Place the remote key against the start button or other sensing area; 4. Simply replace the battery. Keyless start is part of a smart car, a button device that simplifies the starting process and can also turn off the engine. The functions of keyless start include: 1. Multiple start modes; 2. Convenience and speed; 3. Stable and reliable performance; 4. Smart sensing entry; 5. Free switching between dual modes of the smart key; 6. Smart card backup key; 7. Intelligent silent car wash mode.
16
3
Share

Where is the transmission oil filler port located on the Mistra?

The transmission oil filler port on the Mistra is located at the upper left corner of the engine. The transmission is a mechanism used to alter the speed and torque from the engine, capable of fixed or stepped changes to the transmission ratio between the output and input shafts. The Mistra is a 4-door, 5-seater sedan launched by Beijing Hyundai. Taking the 2021 Mistra Flagship Edition as an example, its body dimensions are: length 4780 mm, width 1815 mm, height 1460 mm, with a wheelbase of 2770 mm and a fuel tank capacity of 52 liters. The 2021 Mistra Flagship Edition is equipped with a 1.5T inline 4-cylinder turbocharged engine, delivering a maximum power of 125 kW at 5500 rpm and a maximum torque of 253 Nm between 1500 to 4000 rpm.
20
1
Share

What Causes Insufficient Power When Going Uphill?

There are several reasons why a car may experience insufficient power when going uphill: 1. Fuel system issues: The fuel system is a common source of problems in vehicles. Insufficient fuel entering the combustion chamber could be caused by clogged fuel injectors, fuel line leaks, reduced fuel pump performance, or a blocked fuel filter. 2. Poor fuel quality: If using substandard gasoline with excessive impurities, these contaminants can clog small passages or filtration components in the fuel system (such as the fuel pump screen, fuel filter, or fuel injectors) during engine operation, leading to poor fuel delivery and reduced engine performance. 3. Carbon buildup: Excessive carbon deposits in the throttle body or intake manifold can restrict airflow, preventing complete combustion of gasoline and resulting in power loss, along with increased fuel consumption. Clogged fuel injectors may cause poor fuel atomization or complete failure to inject, leading to cylinder misfire and reduced engine output. 4. Faulty ignition coil: A damaged ignition coil may prevent a cylinder from firing properly, causing power loss due to cylinder misfire and accompanied by engine vibration. 5. Fuel pump failure: A malfunctioning fuel pump may not deliver sufficient fuel, ultimately causing inadequate fuel injection and reduced engine power output, resulting in overall vehicle power deficiency.
13
5
Share

How to Determine if the Volkswagen EA888 PCV Valve is Good or Bad?

Methods to determine if the Volkswagen EA888 PCV valve is good or bad include: 1. Check if there is blue smoke coming from the exhaust pipe; 2. Open the oil filler cap and see if there is severe suction. The PCV valve is installed between the compressor outlet and the condenser inlet, and its function is to improve the heat transfer effect in the condenser and evaporator through separation. Volkswagen is a brand under the German Wolfsburg Automobile Manufacturing Company, and its models include: Magotan, Lavida, Phaeton, Sagitar, Bora, etc. Taking the Magotan 2020 280 Comfort model as an example, its body dimensions are: length 4865 mm, width 1832 mm, height 1471 mm, wheelbase 2871 mm, fuel tank capacity 66 liters, and curb weight 1445 kg.
12
1
Share

What do the gear positions M+ and M- mean?

M stands for Manual, indicating the manual shifting mode. Generally, the + and - signs on an M-gear transmission mean shifting gears by pushing the gear lever forward or backward or using the steering wheel paddles. The following are the technical requirements for shifting gears: 1. Timely: Master the appropriate shifting timing, meaning you should not upshift too early or downshift too late. 2. Correct: The coordination between the clutch pedal, accelerator pedal, and gear lever should be accurate and harmonious, with precise positioning. 3. Smooth: After shifting into a new gear, release the clutch pedal promptly and smoothly. 4. Swift: The action should be quick to minimize shifting time, reduce kinetic energy loss, and lower fuel consumption.
6
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.