What are the reasons why the Peugeot 207 suddenly cannot start?

1 Answers
ArabellaLee
07/30/25 5:16am
Peugeot 207 suddenly cannot start for the following reasons: 1. Insufficient fuel: First, check if the fuel level is insufficient, and then check if there is any issue with the fuel line. 2. Incorrect gear position: For automatic transmission cars, the gear must be placed in P or N when starting. If placed in R or D, the car will not start. Some manual transmission cars may also fail to start if the clutch is not depressed. 3. Dead battery: This could be due to a drained battery caused by leaving the headlights on for a long time or the battery reaching the end of its lifespan. It is generally recommended to replace the battery every 2 years. Additionally, installing xenon headlights, high-power audio systems, or DVD players can also cause vehicle circuit failures.
Was this review help?
16
2
Share
More Forum Discussions

What does a yellow license plate on a car mean?

Car yellow license plate indicates that the vehicle is a large civil vehicle. Yellow-plated vehicles generally refer to large vehicles, such as trucks or buses weighing more than 2 tons (including vans with 12 or more seats), etc. In addition, the vast majority of vehicles for operational purposes, large motorcycles, and vehicles for agricultural use also have yellow license plates. Sedans with a length exceeding 6 meters also require yellow license plates, and a B-class or higher driver's license is needed to drive them. Sedans that can be registered with yellow plates include the Maybach 62S, Audi A8L Extended Edition, Rolls-Royce Phantom LWB, Lincoln Extended Limousine, and Cadillac DTS Extended Edition.
13
2
Share

What Causes Engine Shaking When Turning Off the Ignition?

The causes of engine shaking when turning off the ignition: 1. Uneven cylinder pressure across cylinders; 2. Excessive carbon buildup on intake valves and intake pipes, excessive dirt on throttle valves and inner walls of intake pipes; 3. Incorrect coolant temperature and intake air temperature signals, circuit faults; 4. Excessive carbon buildup or incorrect gap on spark plugs, leakage in high-voltage wires or distributor caps; 5. Fuel injectors not closing properly or clogging due to excessive internal carbon deposits. Engine maintenance methods: 1. Use high-quality engine oil; 2. Use qualified coolant; 3. Regularly clean radiator scale; 4. Regularly remove carbon deposits from the car; 5. Replace the car's three filters on time; 6. Maintain reasonable engine speed.
18
3
Share

What are the precautions for overtaking?

The precautions for overtaking include: 1. Avoid forcing an overtake; do not force an overtake when the vehicle ahead does not yield speed or lane due to certain reasons. 2. Do not forcibly squeeze in when there is not enough safe distance ahead of the vehicle in front, and do not force the overtaken vehicle to yield by crowding it. 3. Maintain a smooth overtaking path during the maneuver. 4. Change to the left lane in advance before overtaking, and delay returning to the right lane after overtaking, keeping the driving trajectory basically parallel to the vehicle ahead. Methods to judge the distance when overtaking are: 1. When the lower edge of the rear wheel of the vehicle ahead aligns with the lower edge of the windshield, the distance is about 3 to 5 meters. 2. When the lower edge of the front bumper of the vehicle ahead aligns with the lower edge of the windshield, the distance is about 2 meters. 3. When the upper edge of the front bumper of the vehicle ahead aligns with the lower edge of the windshield, the distance is about 0.5 to 1 meter.
1
1
Share

What are the reasons for insufficient clamping force of the Haval H6 electronic parking brake?

Explanation of the reasons for insufficient clamping force of the Haval H6 electronic parking brake: 1. Check the model year of the vehicle: Has the brake fluid been replaced? Measure the water content in the brake fluid, which should normally not exceed 3%. If the content exceeds 3%, it needs to be replaced. Excessive water content in the brake fluid can generate gas in the brake lines, leading to poor braking performance. In this case, the brake fluid should be replaced immediately. 2. The electronic parking brake control unit or the parking brake switch is damaged, causing a fault: In this situation, you need to go to a professional workshop and use a diagnostic tool to check the control unit for any fault codes. Replace the damaged parts according to the fault codes. 3. The alternator is not generating electricity: When using the electronic parking brake, the battery cannot provide the normal supply voltage or current, preventing the rear brake pads from clamping the brake disc to the specified torque. In this case, the dashboard will indicate a problem with the parking brake system.
19
1
Share

What are the reasons for HOWO not starting but having power?

Introduction to the reasons why HOWO doesn't start but has power: 1. Check if the fuel level is insufficient: When the car lacks its power source "gasoline," it naturally won't start. If the failure to start is due to lack of fuel, then this situation is relatively easy to resolve. Depending on the circumstances, one can seek help from nearby car owners, request to borrow fuel, or arrange for towing to a gas station as emergency measures. 2. Incorrect gear position: Generally, the P or N gear is the correct position for starting an automatic transmission car. If the driver carelessly leaves the gear in R or another position, the result will not only be failure to start but also pose a safety hazard. 3. Circuit or electronic failure: Circuit failures may include blown fuses, open high-voltage coils, open low-voltage circuits, detached central ignition wires, leaking distributor rotors, or damaged spark plugs. Electronic failures mainly refer to the central computer control board losing functionality. 4. Fuel system failure: Possible locations of fuel system failures include malfunctioning fuel pumps, blocked fuel lines, clogged fuel filters, carbon buildup on spark plugs, damaged fuel injectors, etc.
14
1
Share

Which button is used to reset the trip mileage on the Haval H6?

The trip mileage reset button on the Haval H6 is the zero/adjustment button located at the lower right corner of the settings, which allows switching between two mileage display modes. In the single trip mileage display mode, press and hold the zero/adjustment button for more than two seconds to reset the single trip mileage or small mileage display value to zero. However, the total mileage "TOTAL" mode cannot be cleared unless the engine is replaced. Below is some knowledge about the Haval H6: 1. Design evolution: After three generations of glorious development, the third-generation Haval H6 boasts a powerful presence; its Eastern-style futuristic aesthetic design language highlights strong dynamic power through exterior lines, while the interior features a super-sensory futuristic smart cockpit design. 2. Intelligent evolution: With over a thousand intelligent upgrades, it integrates cutting-edge smart technologies, including not only full-vehicle FOTA upgrades but also supports ultra-L2-level autonomous driving, featuring 22 intelligent driving assistance functions such as full-scenario AEB automatic emergency braking, 50-meter fully automatic tracking reverse, and intelligent evasion.
18
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.