What are the reasons why the Haval H2 does not blow cold air when the AC is turned on?

What is the recommended engine oil specification for Honda XR-V?

For Honda XR-V under normal temperature conditions, it is recommended to use SAE 0W-20 engine oil with SM or higher grade. Alternatively, you may use Mobil 1 full synthetic 0W-20 oil. For subsequent maintenance oil changes, you can choose from brands such as Mobil, Shell, Castrol, or Total. The viscosity of engine oil varies with temperature, so special attention should be paid to its performance under both low and high temperature conditions. Taking 5W-30 as an example: the first number indicates low-temperature fluidity - 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, resulting in smoother cold starts. The latter number represents the oil's kinematic viscosity at 100°C - higher values indicate better ability to maintain viscosity under high temperatures, which can be understood as superior lubrication performance in high-temperature conditions. The oil change procedure for Honda XR-V is as follows: Wait for the engine to cool down, allowing the oil to fully drain back to the oil pan; Loosen the drain plug with a wrench and collect the used oil in a container until the flow stops completely. Start the engine and let it run for 30 seconds to drain remaining oil from the main oil passages; Remove the oil filter using a special wrench; Apply new oil to the gasket of the new oil filter and tighten it clockwise by hand; Add new oil through the valve cover filler opening, typically filling about three-quarters of a standard oil container; Run the engine for 5 minutes and check for leaks around the drain plug and oil filter. Repair if necessary; After stopping the engine, remove the dipstick to verify the oil level falls within the standard range.

14

4

Share

How to Determine the Number of Pistons in a Caliper?

Method to determine the number of pistons in a caliper: The caliper will have several circular protrusions, which are the pistons. Multiply the number of protrusions on one side by two to calculate the total number of pistons. A car caliper is a clamp-like device that functions to slow down, stop, or maintain the stopped state of moving wheels, typically used only in disc brake systems. It is the protruding part on the outer side of the brake pad and serves as a component that enhances braking performance. The disc brake system in a car consists of a brake oil pump, a brake disc connected to the wheel, and a brake caliper on the disc. During braking, high-pressure brake oil pushes the pistons inside the caliper to press the brake pads against the brake disc, thereby generating the braking effect.

16

5

Share

Is the Dongfeng Junfeng e11k a pure electric vehicle?

Dongfeng Junfeng e11k is a pure electric vehicle, a single-motor compact sedan. The maximum power of this car's motor is 100kw, and the maximum torque is 260 Nm. The car uses a ternary lithium battery, and the range given by the Ministry of Industry and Information Technology is 405 kilometers. The body dimensions of the Dongfeng Junfeng e11k are 4665mm in length, 1700mm in width, and 1540mm in height, with a wheelbase of 2700mm. The door structure is a 4-door, 5-seater sedan with a trunk volume of 504 liters. The driving method is front-engine front-wheel drive, with a front suspension using MacPherson independent suspension and a rear suspension using a torsion beam non-independent suspension.

5

0

Share

What are the consequences of abruptly pressing the accelerator pedal when starting on icy or snowy roads?

Abruptly pressing the accelerator pedal when starting on icy or snowy roads can cause the vehicle to lose control, so it is advisable to gently apply the brakes when driving on such surfaces. Precautions for driving on icy or snowy roads: Always allow extra braking distance: When driving on snow, the friction coefficient decreases, making braking more difficult to control. Generally, ABS can prevent wheel lock-up by continuously applying the brakes, so it is recommended to maintain firm pressure on the brake pedal for maximum braking effectiveness. However, on icy or snowy roads, this approach may result in poorer braking performance. Ensure clear visibility through the front and rear windshields: Before driving in snowy conditions, first check if the windshield wipers and washer fluid are functioning properly. Snow melting from the roof can flow down the front windshield, and mud or dirt kicked up by vehicles ahead can also splash onto the windshield. In such cases, use the washer fluid and wipers to maintain clear visibility. Apply the accelerator gently: On icy or snowy roads, avoid pressing the accelerator pedal as deeply as you would normally. Instead, apply gentle pressure to maintain forward motion without excessive acceleration. It is also advisable to keep the transmission in a lower gear, such as third gear. This not only helps control speed through engine braking but also makes it easier to achieve a reasonable forward speed.

6

3

Share

Can the car windshield be left without film?

Car windshields can be left without film, as car window tinting is not mandatory or essential but rather a personal preference. Applying film can reduce exposure to sunlight and UV rays, and the windshield is the primary area where the performance of explosion-proof and heat-insulating films—such as explosion resistance, heat insulation, and anti-glare—is most evident. The car windshield has a laminated interlayer designed for explosion resistance, and modern windshields generally come with UV protection and heat insulation features. The vehicle's windshield is the main source of heat radiation that raises the temperature inside the car. Applying film can relatively improve the driving environment, reduce air conditioning energy consumption, and achieve energy-saving effects.

7

2

Share

Which Vehicles Require Urea?

Vehicles that require urea include: heavy-duty trucks, buses and other diesel vehicles. Automotive urea refers to diesel exhaust fluid (DEF), primarily used in SCR technology to reduce nitrogen oxide emissions from diesel exhaust. To meet annual emission inspection standards, diesel vehicles must be equipped with an SCR system for exhaust treatment. Automotive urea is used by the SCR system to process nitrogen oxides in exhaust gases. DEF is an essential additive for SCR systems. When nitrogen oxides are detected in the exhaust pipe, the urea tank automatically sprays DEF, which undergoes redox reactions with nitrogen oxides in the SCR catalytic converter, producing harmless nitrogen gas and water vapor for emission.

11

0

Share

What are the reasons why the Haval H2 does not blow cold air when the AC is turned on?

What is the recommended engine oil specification for Honda XR-V?

How to Determine the Number of Pistons in a Caliper?

Is the Dongfeng Junfeng e11k a pure electric vehicle?

What are the consequences of abruptly pressing the accelerator pedal when starting on icy or snowy roads?

Can the car windshield be left without film?

Which Vehicles Require Urea?

How to Adjust Headlights?

What is the Volkswagen Bora?

What are the solutions for a heavy steering wheel in the Sagitar?

Which Versions of the Tiguan L Come with a Particulate Filter?