What Are the Reasons for Water Inside the Car on Rainy Days?

The Difference and Function Between Magnetic Brake and Centrifugal Brake

Centrifugal brakes perform better in long-distance casting than magnetic brakes, but they lack stability and are prone to line bursts in strong winds. Magnetic brake baitcasting reels offer better stability during casting but are less effective with light lures. The shapes of their brake discs are also different. Below is an introduction to the functions of magnetic brakes and centrifugal brakes: 1. The function of a magnetic brake is based on the principle that magnetic lines can pass through metal materials. When the spool is rotated by the line, it cuts through the magnetic lines, generating resistance to control the spool's speed and reduce line bursts. 2. The function of a centrifugal brake is that when the lure flies forward, the line drives the spool of the baitcasting reel to rotate. The centrifugal weights on the spool move outward along the centrifugal disc, rubbing against the centrifugal ring to create friction, thereby controlling the spool's speed. The faster the spool rotates, the greater the centrifugal braking force, and the more centrifugal weights used, the stronger the braking force.

1

5

Share

What are the reasons for a sudden increase in fuel consumption in diesel trucks?

Diesel trucks suddenly consuming more fuel may be due to the following reasons: 1. Insufficient tire pressure or aging tires. When tire pressure is too low, the contact area between the tires and the ground increases, leading to higher rolling resistance and increased fuel consumption. 2. Clogged air filter. A blocked air filter can restrict airflow, reducing the amount of air entering the engine and causing higher fuel consumption. 3. Insufficient fuel injector pressure, resulting in poor diesel atomization. 4. Cylinder wear or air leakage, leading to low cylinder pressure and poor combustion efficiency, which increases fuel consumption. 5. During winter, fuel consumption is naturally higher. If winter-grade diesel is not used or the diesel grade is inappropriate, it can also lead to increased fuel consumption.

3

0

Share

What are the differences between Auto Hold and Engine Start-Stop?

Auto Start-Stop and Auto Hold are two completely different functions that cannot be compared together, so there is no question of what the differences are. Here is relevant information about Auto Start-Stop and Auto Hold: 1. Auto Start-Stop means that when the vehicle comes to a stop and the brake is pressed firmly, the engine will shut off. Pressing the accelerator will automatically restart the engine. Auto Start-Stop is a feature developed by manufacturers to save fuel. According to authoritative tests, vehicles with Auto Start-Stop can save 10% to 15% of fuel annually. 2. Auto Hold means the vehicle can determine whether to automatically apply the brakes based on actual conditions. Auto Hold is an extension of the ESP function, controlled by ESP components. The Auto Hold button is usually located next to the electronic parking brake. On some vehicles, it is labeled "A," while others display "AUTOHOLD" directly. Pressing the Auto Hold button will show "ON," indicating that the function is activated. 3. Auto Hold can only operate properly when the seatbelt is fastened and the doors are closed. Pressing the accelerator, shifting gears, or turning the steering wheel will deactivate Auto Hold.

6

5

Share

Is Wheel Balancing Necessary After Changing Tires?

Wheel balancing is necessary after changing tires. It is essential to perform wheel dynamic balancing after swapping the front and rear tires of a car. A car's wheel is an assembly consisting of the tire and the rim. However, due to manufacturing reasons, the mass distribution of this assembly cannot be perfectly uniform. Relevant information is as follows: 1. When the car's wheels rotate at high speeds, dynamic imbalance occurs, leading to phenomena such as wheel shaking and steering wheel vibration during driving. 2. In dynamic conditions, wheel balance is corrected by adding counterweights to balance the edges of the wheel. This correction process is known as dynamic balancing.

1

5

Share

Can vehicle annual inspection be done in another location?

Vehicle annual inspection can be conducted in another location. Starting from September 1, 2018, cross-province inspection for small cars, trucks, and medium-sized buses has been fully implemented. Applicants can directly undergo inspection in provinces other than the vehicle registration location and obtain the inspection compliance mark without the need to go through the entrusted inspection procedures. Relevant information is as follows: 1. For motor vehicles that are driven on the road after registration, regular safety technical inspections should be conducted according to laws and administrative regulations, based on different circumstances such as vehicle usage, passenger and cargo capacity, and service life. 2. For those who provide the motor vehicle driving license and the compulsory third-party liability insurance policy, the motor vehicle safety technical inspection institution shall conduct the inspection, and no unit may impose additional conditions. 3. For motor vehicles that meet the national safety technical standards, the traffic management department of the public security organ shall issue the inspection compliance mark.

14

2

Share

Where is the Three-Way Catalytic Converter Located in the Engine?

The three-way catalytic converter is generally installed in the first bulge of the exhaust manifold under the car chassis, resembling a long kettle-shaped device. Here are the functions of the three-way catalytic converter: 1. The three-way catalytic converter is designed to process harmful gases such as CO, HC, and NOx emitted from the vehicle's exhaust. 2. Through oxidation and reduction reactions, these harmful gases are converted into harmless carbon dioxide, water, and nitrogen, thereby purifying the vehicle's exhaust. The working principle of the three-way catalytic converter is as follows: 1. When the engine exhausts gases through the exhaust pipe, CO, HC, and NOx pass through the catalyst in the three-way catalytic converter, which enhances the activity of these gases, facilitating oxidation-reduction chemical reactions. 2. Among them, CO is oxidized into colorless, non-toxic carbon dioxide gas at high temperatures, HC compounds are oxidized into water (H2O) and CO2, and NOx is reduced into nitrogen (N2) and oxygen (O2).

6

3

Share

What Are the Reasons for Water Inside the Car on Rainy Days?

The Difference and Function Between Magnetic Brake and Centrifugal Brake

What are the reasons for a sudden increase in fuel consumption in diesel trucks?

What are the differences between Auto Hold and Engine Start-Stop?

Is Wheel Balancing Necessary After Changing Tires?

Can vehicle annual inspection be done in another location?

Where is the Three-Way Catalytic Converter Located in the Engine?

What needs to be replaced during a car's first maintenance?

When is the first maintenance for a vehicle?

What is the Principle of Drifting?

How to Clean and Disinfect Car Air Conditioning?