···
Log in / Register

What are the reasons for water ingress in the Passat Lingyu cabin floor mats?

4 Answers
RicardoRose
07/29/25 7:43am
Passat Lingyu cabin floor mats water ingress reasons are as follows: 1. Reason one: It may be caused by leakage from the drainage plug at the bottom of the compartment, leakage from the sunroof drainage pipe, door leakage, leakage of antifreeze from the heater core, damage or improper installation of the air conditioning drainage pipe, etc. Open the engine compartment (front cover), remove the battery, and you can see the drainage hole. Remove the funnel-shaped rubber pad of the drainage hole with a screwdriver. 2. Reason two: There are also multiple possibilities, one is sunroof leakage due to poor sealing, check the sunroof; the second is water from car washing that was not cleaned properly; the third is rusting of the car's small water tank, which is used for cabin heating, leading to leakage. Remove the soaked comfort control module, blow it with an air pump, and use a towel to absorb the water from the cabin floor.
Was this review help?
11
0
Share
DiEzra
08/13/25 2:03am
I've been driving the Passat Lingyu for a while now. Last summer, I suddenly noticed water seeping into the footwell of the driver's compartment, leaving water stains all over the floor. The cause might be a clogged sunroof drain hole, especially since this car's design makes the drainage pipes prone to accumulating leaves and dust, causing rainwater to backflow into the footwell. Aging door seals are also a common issue—once the rubber strips wear out, rainwater can seep in through the door gaps. Another potential problem is a blocked air conditioning drain pipe; if water isn't properly drained when using the AC in summer, it can flow back inside. Back then, I checked the sunroof and found leaves stuck in it—clearing them solved the issue. Still, I recommend first cleaning the drain holes as a simple fix. If that doesn’t help, visit a professional shop to inspect the seals or drainage system. Address it promptly to avoid interior corrosion or electrical shorts, which could compromise driving safety. Leaving this problem unchecked can also lead to foul odors or electrical malfunctions, so it's best not to tamper with it yourself.
Was this review help?
3
1
Share
Expand All
AutumnMarie
10/05/25 2:01am
As a newbie who just started driving a Passat Lingyu, I once found the floor mats completely soaked with water after parking in a heavy rain. Common causes include an improperly closed sunroof or clogged drainage holes trapping rainwater on the roof; aging or cracked door seals that easily leak; a blocked AC drain pipe causing water to back up; or holes/gaps under the car allowing rainwater to seep in. I first checked the sunroof and door seals myself—cost-effective and convenient. Using a thin stick to clear the drainage holes can prevent issues. If that doesn’t work, inspect the drain pipe location. Regular maintenance is advised, especially cleaning before the rainy season to avoid water damage, short circuits, or odors that could lead to costly repairs. Addressing this promptly ensures driving comfort and prevents bigger failures.
Was this review help?
6
0
Share
Expand All
Francis
11/18/25 3:30am
I've been driving this car for several years, and water ingress in the floor mats usually stems from a few common causes: clogged sunroof drainage tubes allowing rainwater to seep in, aging door seals failing to keep water out, improper air conditioning drainage causing backflow, or cracks in the vehicle body. When I discovered the issue, I used towels to absorb the moisture and checked the sunroof and door edges for debris. Prevention is key—cleaning the drainage holes monthly to avoid water accumulation ensures long-term vehicle safety and protects internal components. Addressing such minor issues promptly can prevent electrical problems.
Was this review help?
6
0
Share
Expand All
More Forum Discussions

Which country does GAC FCA belong to?

GAC FCA is not an automobile brand, but a Chinese company, whose full name is GAC Fiat Chrysler Automobiles Co., Ltd. It is a company jointly established by Guangzhou Automobile Group and Fiat Chrysler Automobiles Group. The following is the relevant introduction of GAC FCA: 1. GAC Fiat Chrysler Automobiles Co., Ltd. was established on March 9, 2010, jointly invested and constructed by Guangzhou Automobile Group Co., Ltd. and Fiat Chrysler Automobiles Group with a 50:50 share ratio. 2. GAC Fiat mainly produces Jeep and Fiat models. Among them, Jeep is a brand from the United States, while Fiat is an Italian brand. Fiat Chrysler Automobiles Group is an Italian company, which owns brands such as Dodge, Ferrari, Maserati, Alfa Romeo, and Jeep.
16
0
Share

What does the yellow exclamation mark on the Honda XR-V dashboard mean?

The appearance of an exclamation mark on the car dashboard indicates an abnormality or malfunction in the corresponding system. There are many dashboard indicator lights with exclamation marks, such as the tire pressure indicator, lighting fault indicator, steering system fault indicator, brake system fault light, transmission fault indicator, and wiper fault indicator. Below is a detailed introduction to the exclamation mark fault lights: General faults: A triangle with an exclamation mark inside. If this symbol lights up, it indicates a fault in the car's general performance, components, or functions. Main issues include parking sensor failure, fuel cutoff system intervention or malfunction, external light failure, engine oil pressure sensor failure, etc. It is necessary to visit a 4S shop for inspection to identify the source of the fault. Automatic transmission fault: A yellow gear with an exclamation mark inside. This is the automatic transmission fault warning light, indicating a fault in the transmission or transmission lubricant level below the normal range. The transmission oil should be replaced promptly. Brake system fault: A circle with an exclamation mark inside parentheses. This represents a brake system warning, mainly indicating a brake system malfunction or low brake fluid level. The brake system should be inspected immediately to avoid accidents. Abnormal tire pressure: A horizontal line with an exclamation mark inside parentheses. This represents the tire pressure monitoring warning light, which lights up when the car's tire pressure is too low. Check the car's tire pressure and restore it to the normal range. Lighting fault: A yellow bulb with an exclamation mark. This is the lighting fault indicator, indicating a fault in the car lights. Solution: Go to a 4S shop for inspection as soon as possible, or check it yourself, focusing on commonly used bulbs such as turn signals, fog lights, and interior lights, to identify the problem. In addition, during daily use of the vehicle, the fault lights displayed on the vehicle dashboard are divided into two different colors: yellow and red: Yellow indicates a fault in the corresponding system, but the problem is not very serious. Reduce speed and proceed to the corresponding repair point for maintenance to eliminate potential safety hazards in time. Red indicates a very serious problem in the corresponding system. In this case, do not continue driving. Pull over immediately and call for professional help to prevent unpredictable dangers to the vehicle and personal safety caused by forced driving. It should be noted that when the car is started, all lights will turn on, and the system will perform an automatic check. After the check is completed, the lights will turn off automatically. If a light does not turn on when the ignition is turned on, remains on without turning off, or lights up while driving, it indicates a fault in the related system. In such cases, seek professional help promptly for car inspection to eliminate potential safety hazards.
3
0
Share

How to Install Door Edge Guards?

First, clean the door surface. Then peel off a small section of the edge guard and insert it into the door edge. While pressing it down, continue peeling off the backing tape. Finally, trim off any excess material. Before installation, use a clean towel to wipe the mounting area. Peel back a portion of the adhesive backing tape inside the edge guard and carefully insert the guard into the door edge or other installation position. As you press the guard into place, gradually remove the remaining double-sided tape backing. Align with the door edge and cut off any extra length. Below is relevant information about door edge guards: 1. Door edge guards, also known as protective strips, anti-scratch trims, bumper guards, or side moldings. Installing them effectively prevents paint scratches on door panels when opening doors and avoids damaging other vehicles' paint when parked too closely. 2. There are three structural attachment methods for edge guards: Recessed type - where the vehicle body has pre-formed grooves during manufacturing for guard insertion. Surface-mounted type - where the vehicle body remains flat with pre-drilled holes for guard pegs to insert and adhere. Fixed type - where guards are secured to the vehicle body using nuts and bolts.
19
3
Share

How Many Types of Lights Does a Sedan Have?

Automotive lighting mainly includes headlights (comprising high beam and low beam), front position lights, rear position lights, license plate lights, instrument panel lights, turn signals, brake lights, hazard warning flashers, reverse lights, and front fog lights. Below are the relevant introductions: 1. The front-end headlights are divided into low beam and high beam. High beam is used in situations with very poor lighting and no auxiliary light sources, while low beam is used during relatively bright nights. 2. Fog lights are used when road conditions are not very clear, such as during foggy weather when visibility is poor. These lights are located at both the front and rear of the vehicle, with only one on each side, asymmetrical, and differentiated from other lights of the same color. 3. Brake lights illuminate when braking and are typically installed at the rear end of the vehicle, in a conspicuous red color. Additionally, there are reverse lights, which are positioned at the rear end of the vehicle, on either side of the trunk. The two types of lights differ in color, with reverse lights being white.
15
4
Share

How to Activate OnStar for a New Car?

The method to activate OnStar for a new car is as follows: After getting into the car, press the blue OnStar button in the middle of the rearview mirror twice to directly connect to the OnStar service center. Inform the customer service representative that you have just purchased a car equipped with OnStar and wish to activate it. Then, follow their instructions step by step to set up a password and identity information. Below is an introduction to OnStar's related features: 1. Automatic Collision Assistance. When the built-in collision sensors in the vehicle detect a collision or airbag deployment, they automatically send an alert to the command center. A professional advisor will then contact the vehicle via voice communication. 2. Automatic Assistance for Airbag Deployment. Once the airbags are deployed, OnStar will receive the information and contact the vehicle owner. 3. Medical Emergency Assistance.
17
1
Share

Where is the handbrake on Honda Jade

Honda Jade uses a foot-operated parking brake. The brake pedal is located next to the left foot, smaller than the main brake pedal. Pressing it all the way down is equivalent to pulling the handbrake, and pressing it again releases the handbrake. Here is some related information: 1. When JADE (Jade) was first launched in September 2013, it immediately attracted the attention of many urban young people and quickly became a best-selling model. The most striking features of JADE (Jade) are its stylish appearance and spacious interior. 2. Like other Honda models, JADE (Jade) has a relatively short engine compartment, but this does not affect the vehicle's ability to withstand frontal collisions. After the C-NCAP 64km/h frontal 40% offset collision test, the passenger compartment structure of JADE (Jade) remained very intact, with no significant deformation in key areas such as the A-pillar and B-pillar. The intrusion deformation of the steering column and pedals was also well controlled.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.