···
Log in / Register

What are the reasons for the windshield wiper not spraying water?

5 Answers
StAndres
07/23/25 6:45pm

Specific reasons for the windshield wiper not spraying washer fluid: 1. Pipe blockage: Frequent driving on unpaved roads can cause tiny dust particles to enter the spray holes of the wiper. Over time, the dried dust can block the spray holes, preventing the wiper from spraying water. Simply insert a brush into the wiper spray holes to clean out the dust or attached dirt, and turn on the wiper spray switch while cleaning. 2. Water level too low: The washer fluid container for the wiper is designed in the engine compartment. If the water level is too low, it will also prevent water from spraying. In this case, just add water to the washer fluid container.

Was this review help?
11
2
Share
MacAlex
08/10/25 2:21pm

I had only been driving for less than two years when I encountered the issue of the windshield washer not spraying water. That time, I was in a hurry to go out and found it completely unable to spray—turns out the washer fluid bottle was empty, as I had been too lazy to check and kept forgetting to fill it up. Another common problem is the nozzles getting clogged with mud, especially after driving on dirty roads for a long time. Using a small pin to poke them usually does the trick. If the water pump is broken, you won’t hear the usual humming sound near the engine, or it might make a loud noise but nothing happens—get it fixed immediately. If the pipes are cracked or leaking, you’ll see water stains on the ground. Electrical issues are less common, but a blown fuse or poor switch contact can cause this. Winter is even more troublesome, as the water can freeze into ice in the reservoir—you’ll need warm water to thaw it before using antifreeze washer fluid. It’s a good idea to keep a bottle of water in the trunk and check the fluid level before driving. If the spray isn’t working properly, don’t force it—either take a different route or stop to fix it. Safe driving starts with clear visibility, so don’t take it lightly.

Was this review help?
20
5
Share
Expand All
SaraMarie
09/22/25 9:13am

Fellow car enthusiast, I've figured out the windshield washer issues from my daily tinkering: the simplest fix for running out of washer fluid is just to refill it; if the spray nozzles are clogged, use a pin to clear them; water pump failures are often due to aging or excessive dust, making noise but not spraying; you can smell fluid if the pipes crack; for electrical issues like blown fuses or controller glitches, check the manual for corresponding points; in cold weather, if the water freezes, thaw it with hot water and switch to antifreeze. Make it a habit to check the reservoir level before refueling, and clean the spray nozzles monthly to avoid emergencies on the road. Also, avoid modifying the electrical system randomly to prevent interference, and it's best to carry a spare bottle of fluid on long trips. This little thing is small but crucial—poor visibility on wet roads is too dangerous. Early checks save worry and ensure safety.

Was this review help?
4
2
Share
Expand All
VonGenesis
11/06/25 3:33am

When driving with kids, I'm particularly worried about the windshield wipers not spraying water. The main reasons are: the washer fluid is empty—too busy with school runs to remember to refill; the nozzles are clogged, with dirt accumulating into blocks during car washes; the water pump is faulty, making loud noises but not dispensing water; the pipes are broken, leaking everywhere and needing urgent repair; electrical shorts or blown fuses are rare; in winter, the water freezes, but warming it up solves the issue. My advice: keep the reservoir full, clean the nozzles regularly, and prioritize clear visibility for safe driving—never force it in the rain. Safety when transporting kids is more important than anything else.

Was this review help?
7
3
Share
Expand All
OCharlotte
12/27/25 5:21am

Step-by-step method: Common reasons why the windshield washer doesn't spray water. Check if the washer fluid reservoir is empty, refill if low; if the nozzle is clogged, gently unclog it with a needle; if the water pump is faulty, listen for operation sounds but no water sprays; look for leaks if the hose is damaged; check the fuse for burns or loose switches in the electrical circuit; in winter, if the reservoir is frozen, use warm water to thaw and replace. Maintenance: Check the water level every three months and clean the nozzles frequently. Address faults early for safer driving.

Was this review help?
9
4
Share
Expand All
More Forum Discussions

can you put a car in a moving truck

Yes, you can transport a car inside a moving truck, but it is a complex process that requires careful planning and specific conditions to be done safely and legally. The primary considerations are the gross vehicle weight rating (GVWR) of the moving truck, the dimensions of its cargo bay, and the weight of the car you intend to load. Not all rental trucks are designed for this purpose, and attempting it without proper verification can lead to severe vehicle damage, safety hazards, or legal violations for being overweight. The most critical factor is the truck's payload capacity, which is the maximum weight it can carry, including all your belongings and the car. A standard sedan weighs between 3,000 to 4,000 pounds. You must check the truck's GVWR and subtract its curb weight to find this payload limit. Exceeding it is dangerous and illegal. Consideration Specification Why It Matters Minimum Truck Size 26-foot truck or larger Smaller trucks lack the necessary length and payload capacity. Typical Payload Capacity 6,000 - 10,000 lbs Must accommodate car weight plus household goods. Car Weight (Sedan) 3,000 - 4,000 lbs A significant portion of the total payload. Cargo Bay Length 26+ feet Must fit the car with room to secure it. Ramp Weight Limit Often 1,000 - 1,500 lbs The ramp must support the car's weight during loading. Loading the car is the most hazardous part. You will need professional-grade, long and wide aluminum car ramps capable of supporting the car's weight. The ramps must be securely anchored to the truck's liftgate or floor. Driving the car up requires a steady, careful approach to avoid slipping off the ramps. Once inside, the car must be securely strapped down using wheel nets or axle straps to prevent it from rolling or shifting during transit. For most people, the risks and logistical challenges make using a dedicated car carrier trailer a much safer and more reliable alternative. This is one instance where the DIY approach often creates more problems than it solves.
16
4
Share

can you put carplay in an older car

Yes, you can absolutely add Apple CarPlay to an older car. The most common and effective method is by installing an aftermarket head unit (the stereo system in your dashboard). This involves replacing your factory radio with a new touchscreen display that has CarPlay built-in. The cost, complexity, and final result depend heavily on your car's specific make, model, and year, but it's a very achievable upgrade for most vehicles. The primary way to get CarPlay is through a new head unit. You'll need to find a double-DIN or sometimes a single-DIN (with a flip-out screen) unit that fits your car's dashboard opening. Major brands like Pioneer, Sony, Kenwood, and Alpine offer excellent options. The installation process involves connecting the new unit to your car's electrical system and speakers. For a seamless look, you'll also need a dash kit (a trim piece that makes the new stereo fit perfectly) and a wiring harness adapter (which allows you to plug the new unit into your car's factory wiring without cutting any original wires). This preserves your car's resale value and makes installation much simpler. If replacing the entire head unit seems too involved, there are simpler alternatives. CarPlay adapters are portable screens that connect to your existing factory radio via an auxiliary input or FM transmitter. While easier to install, they often provide a less integrated experience with lower sound quality and more clutter. For some newer "older" cars (typically mid-2010s models), a dealership might offer a software update or an OEM upgrade for the factory infotainment system, but this is rare and often expensive. Upgrade Method Estimated Cost Range Installation Complexity Key Considerations Aftermarket Head Unit $300 - $1,500+ Moderate to High Best sound quality, full integration, retains steering wheel controls. CarPlay Adapter / Portable Screen $100 - $300 Low Plug-and-play, but lower sound quality, less polished look. Dealer Software Update $150 - $600 (if available) Low (if available) Only for select models, maintains OEM look, often limited functionality. Before you decide, check if your existing stereo has an aux-in port or a USB port , as this can simplify the adapter route. Also, consider whether you want to retain steering wheel audio controls; many aftermarket head units support adapters for this. The best balance of performance, aesthetics, and value is almost always a properly installed aftermarket head unit.
11
2
Share

can you put car oil in a motorcycle

No, you should not use car engine oil in a motorcycle. While both are lubricants, they are engineered for fundamentally different engines and operational demands. Using automotive oil in a motorcycle can lead to inadequate lubrication, clutch slippage, and potential long-term engine damage. The primary difference lies in the lubrication system. Motorcycle engines, transmissions, and clutches often share the same oil supply (a "wet clutch" system). Car oils contain friction modifiers designed to maximize fuel economy, but these additives can cause a motorcycle's wet clutch to slip, resulting in poor acceleration, overheating, and premature wear. Motorcycle-specific oils are formulated without these friction modifiers to ensure proper clutch engagement. Furthermore, motorcycle engines operate at significantly higher RPMs and under more stress than car engines. They require oils with specific additive packages to handle increased shear forces and prevent breakdown. Using the wrong oil can lead to increased engine wear. For optimal performance and protection, always use an oil that meets the motorcycle manufacturer's specified certification, such as JASO MA or MA2 for wet clutch systems. This information is found in your owner's manual. Aspect Car Engine Oil Motorcycle Engine Oil Primary Function Lubricates engine only Lubricates engine, transmission, and clutch Friction Modifiers Contains fuel-saving friction modifiers Formulated without clutch-slipping modifiers Certifications API "SN", "SP" JASO MA, MA2, API ratings High-RPM Stability Not optimized for extreme RPMs Additives to resist shear at high RPMs Wet Clutch Compatibility Incompatible, causes slippage Specifically designed for wet clutches
4
3
Share

can you put a decal on a leased car

Yes, you can usually put a decal on a leased car, but it is almost always conditional on your ability to remove it completely without damaging the paint before you return the vehicle at the end of the lease term. The primary concern is avoiding charges for excess wear and tear, which the leasing company will assess. Any permanent alteration or residue that requires professional polishing could result in significant fees. The most critical step is to review your lease agreement. Look for a section titled "Vehicle Return," "Excess Wear and Use," or "Prohibited Modifications." This document is the final authority on what is allowed. Some leases explicitly forbid any alterations, including decals and wraps. If the language is unclear, contact the leasing company directly for clarification. Getting permission in writing (e.g., via email) provides a record if a dispute arises later. Choosing the right decal material is essential for easy removal. High-quality vinyl decals with removable adhesive are your best bet. Avoid permanent adhesives, stickers that feel paper-like, or anything that might crack and leave fragments. The application surface also matters; decals are easier to remove from smooth, factory paint than from textured plastic cladding. Proper application and removal techniques are non-negotiable. Application: Ensure the surface is impeccably clean. Applying the decal in warm weather or warming the panel slightly can improve adhesion and make future removal easier. Removal: Start by gently heating the decal with a hairdryer or heat gun on a low setting to soften the adhesive. Slowly peel it back at a 45-degree angle. Any remaining adhesive can be removed with a commercial adhesive remover (like Goo Gone) or isopropyl alcohol, followed by a gentle car wash and wax. The following table compares common decal types and their implications for a leased car: Decal Type Ease of Removal Risk of Paint Damage Best for Leased Cars? High-Quality Vinyl (Removable) Very Easy Very Low Yes, highly recommended Cheap Vinyl / Bumper Sticker Difficult Moderate to High No, adhesive often fails Magnetic Decals Instant None (if surface is clean) Yes, ideal solution Full or Partial Wrap Professional Job Low if done/removed by pros Possible, but requires lessor approval Ultimately, if you have any doubt about your ability to restore the car to its original condition, it's safer to avoid decals altogether. Magnetic signs offer a zero-risk alternative for temporary display.
1
5
Share

can you put 10w30 oil in a 5w30 car

Putting 10W-30 oil in a car that specifies 5W-30 is generally not recommended. While the engine will likely run without immediate failure, you risk reduced fuel efficiency, poorer cold-weather starting, and potential long-term wear. The key difference lies in the oil's viscosity , or resistance to flow. The first number (5W or 10W) indicates the oil's flow at cold temperatures (W for Winter). A 5W oil is thinner and flows more easily at startup than a 10W oil, ensuring critical engine parts are lubricated faster. Using a thicker 10W oil in cold climates can mean your engine runs with inadequate lubrication for a longer period after ignition. The second number (30) is the oil's viscosity at operating temperature (100°C). Both oils have the same "30" rating, meaning they provide similar protection once the engine is fully warmed up. This is why some people believe the oils are interchangeable. However, the compromise in cold-start protection is significant. Modern engines with tight tolerances are designed for specific oil viscosities to optimize performance and longevity. Deviating from the manufacturer's recommendation can also affect your vehicle's warranty coverage. For most drivers, the potential downsides outweigh any perceived benefits. Stick with the 5W-30 specified in your owner's manual for optimal protection, especially if you experience cold winters. The only scenario where a temporary switch might be considered is if you're in a pinch and 5W-30 is unavailable, but you should change back to the correct oil as soon as possible. Characteristic 5W-30 Oil 10W-30 Oil Why It Matters Cold-Temp Viscosity Thinner, flows easier Thicker, flows slower Faster lubrication on cold starts, reducing engine wear. Cold-Weather Starting Easier, less strain on battery More difficult, increased battery load Critical for reliable operation in winter climates. Fuel Economy Impact Minimal negative impact Can reduce fuel efficiency Thicker oil requires more energy for the engine to pump. Engine Wear Protection Optimal for engines designed for it Suboptimal cold-start protection Adhering to specs ensures long-term engine health. Manufacturer Warranty Maintains compliance Potential risk to coverage Using the wrong oil can void powertrain warranties.
13
3
Share

can you put 3 car seats in the back

Yes, you can fit three car seats in the back of many vehicles, but it is highly dependent on the specific car, SUV, or minivan model. The key factors are the vehicle's interior width, the type of seat belts or LATCH anchors, and the physical size of the car seats themselves. Three-across car seat installations are most consistently successful in wider vehicles like minivans, large SUVs, and some full-size sedans. The primary challenge is the physical width of the car seats. Standard convertible seats are often too wide to fit three side-by-side. To succeed, you will likely need to use narrower, specially designed seats. Models like the Diono Radian 3RXT or Clek Fllo are popular for this purpose because they are slimmer and can be puzzle-pieced together. You also need to check your vehicle's seating configuration. Some cars have narrow, sculpted rear seats that make a secure installation nearly impossible. The type of seat belts matter, too; buckle stalks that are too short or long can interfere with a tight fit. Furthermore, most vehicles only have two sets of dedicated LATCH anchors (the metal bars between the seat cushions for securing child restraints) in the outboard positions. The center seat typically requires a seat belt installation, which is equally safe when done correctly. The only way to know for sure is to test-fit your specific car seats in your specific vehicle. A secure installation means each seat should not move more than one inch side-to-side or forward at the belt path. Vehicle Type Example Models Known for Good 3-Across Fit Key Consideration Minivan Honda Odyssey, Toyota Sienna, Chrysler Pacifica Widest cabins, often with three sets of LATCH. Large SUV Chevrolet Suburban, Ford Expedition, Nissan Armada Bench seats offer the most flexibility. Midsize SUV Hyundai Palisade, Kia Telluride, Ford Explorer May require narrow seats; captain's chairs prevent 3-across. Full-Size Sedan Chevrolet Impala, Dodge Charger Surprising width, but door openings can be challenging. Compact Car Honda Civic, Toyota Corolla Extremely difficult; often only feasible with infant-only seats.
11
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.