What are the reasons for the unsmooth gear shifting in Baojun 730?

1 Answers
Javier
07/29/25 6:26pm
Baojun 730 may experience unsmooth gear shifting due to clutch issues, excessive gear self-locking force, or deformed transmission plates. Clutch issues: Clutch malfunctions can lead to insufficient clutch separation travel, resulting in incomplete clutch disengagement and difficulty engaging gears. In such cases, it is recommended to visit a repair shop to adjust the separation travel. Excessive gear self-locking force: If the gear self-locking force on the clutch side is too high, it can cause difficulty in shifting gears. It is advisable to go to a repair shop to adjust the clutch cable and gear locking mechanism. Deformed transmission plates: If the transmission plates of the clutch pressure plate assembly are deformed for some reason, it can lead to poor separation. It is recommended to replace the pressure plate with a high-quality one that matches the original vehicle specifications.
Was this review help?
3
3
Share
More Forum Discussions

What to Do When the Exhaust Controller is Abnormal?

Here are the reasons for abnormal car exhaust controller: 1. False fault: A fault code is reported, but the system works normally. This may be due to an operation exceeding the computer's control range, causing the computer to feedback a fault code. The code can be cleared first, and then check whether the fault code reappears. 2. Minor fault: The engine does not show obvious faults, but further inspection based on computer detection information reveals a real fault that does not affect normal driving or has minimal impact. It needs to be discovered and resolved promptly. 3. Major fault: Such faults can be felt through visual inspection and driving experience, and they severely affect the normal operation of the engine. Immediate repair is required.
18
5
Share

Where is the car fuel tank located?

The fuel tank of a sedan is generally located in the middle-rear part of the vehicle, depending on the car model. The following factors determine the fuel tank opening position: 1. Vehicle weight distribution: The fuel tank position needs to be designed according to the vehicle's weight balance, with most fuel tanks located at the rear. 2. Driving direction: The fuel filler position also depends on the country's driving direction. In right-hand traffic countries, the fuel filler is usually on the right side, while in left-hand traffic countries, it's designed on the left. 3. Safety considerations: In right-hand traffic countries, the fuel filler is typically on the same side as the driver's seat, positioned diagonally opposite to the driver's location for safety during refueling.
18
3
Share

What's the reason for a truck not responding when starting?

The reasons for a truck not responding when starting are as follows: Insufficient battery power: It may be due to insufficient battery power, which can be checked by measuring the battery voltage with a voltmeter. Excessive carbon buildup: It could be caused by excessive spark plug gap or too much carbon buildup; Faulty high-voltage cap: There might also be a fault in the high-voltage cap connected to the spark plug; If the starter motor can turn the engine during electric start but the engine fails to ignite, promptly check for issues with the spark plug, high-voltage electricity, carburetor, air filter, exhaust pipe, cylinder pressure, valve timing, intake pipe, etc.
19
4
Share

What is the function of a rear axle limited-slip differential?

The functions of a rear axle limited-slip differential are as follows: 1. Compensate for wheel spin: The rear axle limited-slip differential is located between the two rear wheels of the vehicle, and it can compensate for the wheel spin caused by a wheel being suspended in the air, which is a drawback of ordinary differentials. 2. Solve the issue of power loss: The differential continuously transmits power to the spinning wheel that has no resistance, resulting in not only the vehicle's inability to move forward but also a significant loss of power. 3. Enable drifting maneuvers: Generally, rear axle limited-slip differentials are equipped in some high-performance vehicles. Vehicles with a rear axle limited-slip differential can perform large-scale drifting maneuvers during aggressive driving.
4
5
Share

What transmission does the Tiggo 5 use?

Tiggo 5 is equipped with a 7-speed simulated CVT transmission. Here are the relevant details: 1. The Tiggo 5 features a 7-speed simulated CVT transmission paired with a 2.0L naturally aspirated engine, delivering a maximum power of 139 horsepower (102 kW) at 5750 rpm and a peak torque of 182 N·m at 4500 rpm. It also includes a DVVT dual variable valve timing system for both intake and exhaust. 2. Although the new Tiggo 5 still adopts a front MacPherson and rear double-wishbone independent suspension setup, certain improvements have been made compared to the older model. However, the suspension transmits road conditions too clearly, even minor road imperfections are distinctly felt in the cabin, which somewhat affects ride comfort.
19
2
Share

Can You Drive to Get a Flat Tire Repaired?

As long as there is a place nearby where you can inflate the tire, you can drive there slowly. If the distance is too far, it is best not to drive there. Below are the signs of a flat tire: Heavier steering wheel: The friction surface between the tire and the ground increases, and so does the corresponding friction, so steering will require more effort, and the steering wheel will feel heavier. Car imbalance: If a tire is flat, you can clearly feel the car tilting to one side. Slower speed: The car's speed will noticeably decrease, and acceleration will be more difficult than usual. Noise while driving: If the tire is flat, the car will make unusual noises while driving.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.