What are the reasons for the Touareg wiper not spraying water?

What kind of car is FAW Toyota Avalon?

FAW Toyota Avalon is the Asian Dragon, a mid-size sedan under the Toyota brand. The Avalon has a wheelbase of 2870 mm, with length, width, and height measuring 4975 mm, 1850 mm, and 1450 mm respectively. The front suspension of the Avalon uses a MacPherson independent suspension, while the rear suspension employs an E-type multi-link independent suspension. The Avalon is equipped with two engines: a 2.0-liter naturally aspirated engine and a 2.5-liter naturally aspirated engine. It also features safety technologies including a rear cross-traffic emergency braking system, a panoramic parking camera with alert function, and intelligent clearance sonar, among others.

14

3

Share

What is engine oil made of?

Lubricating oil is generally composed of two parts: base oil and additives. The following are related introductions: 1. Lubricating base oils are mainly divided into two categories: mineral base oils and synthetic base oils. Mineral base oils are widely used and consumed in large quantities (about 95% or more), but in some applications, products made from synthetic base oils must be used, leading to the rapid development of these two types of base oils. 2. Mineral base oils are refined from crude oil. The main production processes of lubricating base oils include: atmospheric and vacuum distillation, solvent deasphalting, solvent refining, solvent dewaxing, and clay or hydrogenation supplementary refining. In 1995, China's current lubricating base oil standard was revised, mainly modifying the classification method and adding two special base oil standards for low pour point and deep refining. For the production of mineral lubricating oils, the most important factor is selecting the best crude oil. 3. Additives are the essence of modern high-grade lubricating oils. Proper selection and reasonable addition can improve their physical and chemical properties, endow the lubricating oil with new special properties, or enhance certain properties it originally had to meet higher requirements.

18

2

Share

Must the Clutch Be Pressed When Braking in a Manual Transmission Car?

Whether to press the clutch when braking in a manual transmission car depends on the specific situation. If the car is moving at a relatively high speed and the purpose is only to slow down, there is no need to press the clutch. However, if the braking is for downshifting or stopping, the clutch must be pressed. Below is more information about whether to press the clutch when braking in a manual transmission car: 1. The advantage of pressing the clutch when braking is that it reduces the likelihood of stalling. When the car decelerates, the engine speed will inevitably drop if no additional throttle is applied. If the engine speed becomes too low, it can lead to gear disengagement, causing the car to stall. 2. When the car is moving at a high speed and needs to slow down to a stop, the clutch must be pressed or the gear shifted to neutral. Once the speed drops to an appropriate range, the gear can be shifted to the suitable position based on the specific speed and engine RPM for stopping. 3. When driving a manual transmission car downhill for a long distance, it is best not to shift to neutral or keep the clutch pressed continuously. Doing so eliminates the vehicle's traction, and prolonged braking can cause the brakes to overheat, potentially leading to brake failure in severe cases. Therefore, when descending a long slope, the gear should be in the appropriate position to utilize engine braking in combination with the brakes for effective deceleration.

13

0

Share

What is the wheelbase of the Karry K50?

The wheelbase of the Karry K50 is 2755 millimeters. The dimensions of this vehicle are 4501 millimeters in length, 1760 millimeters in width, and 1790 millimeters in height. The Karry K50 is an MPV model, and it is equipped with a 1.5-liter naturally aspirated engine across the entire lineup. The 1.5-liter naturally aspirated engine of the Karry K50 delivers a maximum power of 80 kilowatts and a maximum torque of 140 Newton-meters. The front suspension of the Karry K50 uses a MacPherson independent suspension, while the rear suspension employs a torsion beam non-independent suspension. The torsion beam suspension is a relatively simple non-independent suspension structure, characterized by its compact size and minimal space occupation. Using a torsion beam suspension at the rear can expand the rear seating space and trunk space.

14

1

Share

What does National IV refer to?

National IV refers to China 4. Below is the relevant introduction to the China 4 standard: 1. The National Fourth Stage Motor Vehicle Pollutant Emission Standard, abbreviated as the "China 4 Emission Standard" or "National IV Standard," has relatively looser emission limits for in-use vehicles compared to new vehicles under the China 4 standard. However, it is still 34% stricter than the limits of the China 3 standard. In Beijing, National IV vehicles are initially inspected every two years, and some National IV vehicles are gradually starting to undergo annual inspections. During these inspections, the vehicle's emissions must meet the published standard limits; otherwise, maintenance is required, and the vehicle must pass the inspection to be cleared. 2. The China 4 emission standard was implemented starting in 2011 and remained in effect until 2018 when the China 5 standard was introduced. The China 4 standard requires that the emission levels of various pollutants be approximately 50% lower than those of the China 3 standard.

1

2

Share

How to Adjust the Height of the Steering Wheel?

There is a locking lever under the driver's steering wheel. Pull the locking lever upward, adjust it to the appropriate height, and then firmly press the locking lever to lock the steering wheel. Below is some additional information: 1. The earliest cars used a tiller for steering. This transmitted severe vibrations generated during driving to the driver, making it difficult to control the direction. After the engine was relocated to the front of the vehicle, the increased weight made it impossible for the driver to steer using the tiller. The new design of the steering wheel emerged to address this issue. It introduced a gear system between the driver and the wheels, offering flexible operation and effectively isolating severe vibrations from the road. 2. The steering wheel is connected to the steering shaft via splines. Its function is to convert the force applied by the driver into torque, which is then transmitted to the steering shaft. Using a larger-diameter steering wheel reduces the hand force required by the driver when turning. The steering intermediate shaft serves as a connector between the steering gear and the steering shaft, facilitating the standardization of the steering gear. It compensates for errors during manufacturing and installation, making the installation of the steering gear and steering wheel more reasonable in the vehicle.

17

3

Share

What are the reasons for the Touareg wiper not spraying water?

What kind of car is FAW Toyota Avalon?

What is engine oil made of?

Must the Clutch Be Pressed When Braking in a Manual Transmission Car?

What is the wheelbase of the Karry K50?

What does National IV refer to?

How to Adjust the Height of the Steering Wheel?

Can You Drive a Car Wearing Sandals?

How much does the BYD Qin body weigh?

What is the engine model of the Mercedes-Benz GLS?

How to Solve the Problem of Unable to Press the Brake in an Automatic Transmission Car?