What are the reasons for the soft brakes of SAIC Maxus V80?

1 Answers
Clyde
07/29/25 4:28pm
The reasons for the soft brakes of SAIC Maxus V80 include the following: 1. Mixed use of brake fluid: Different brands of brake fluid are mixed, resulting in reduced braking performance. 2. Air in the brake fluid: The brake fluid contains air that has not been bled out. 3. Oil leakage and poor sealing: The master cylinder and wheel cylinders have oil leakage issues and poor sealing. 4. External packaging damage: The outer casing of the brake lines is damaged. Additional information: As a critical component for safe driving, brakes should be given special attention by every driver. Before each drive, it is advisable to test the working condition of the brake pedal. Before starting the engine, the brake pedal will feel very firm; after the engine is started normally, the brake pedal will sink slightly.
Was this review help?
13
2
Share
More Forum Discussions

How to Replace the Key Battery for Mercedes-Benz GLA?

On the side of the Mercedes-Benz GLA remote, there is a PUSH button. Press this push metal head, and the mechanical key will come out. After it comes out, a small groove and a slit will be exposed on the top. Pry it open with force, and the key will split into two halves as you apply pressure. The side with the circuit board is where the battery is located. Flip it over, remove the old battery, and place a CR1632 battery in the metal frame. Then, put the circuit board back in place and close the two halves together. 1. Method for opening the car remote key to replace the battery: There is a circle on the back of the remote key with a groove in the middle. Use a coin to press into the groove and twist open the cover to see the button battery. The groove is on the edge between the front and back of the remote key. Use an appropriate tool according to the size of the groove to twist it open. Buy a new battery with the same number as the original one for replacement. 2. Working principle: First, the key emits a weak radio wave, which is received by the car antenna. The electronic control unit identifies the signal code, and then the actuator of the system performs the action of locking/unlocking.
18
5
Share

Can I directly obtain an automatic transmission driver's license?

You can directly obtain an automatic transmission driver's license, which is the C2 driver's license. The C2 driver's license only permits driving automatic transmission passenger cars and does not allow driving manual transmission vehicles. Automatic transmission vehicles do not have a clutch, making them easier to control and significantly different from manual transmission vehicles. Holders of a C2 license cannot drive manual transmission vehicles, while holders of a C1 license can drive automatic transmission vehicles. Therefore, the C1 license is downward compatible with the C2 license, and the C2 can be considered a subset of the C1. C2 is the automatic transmission driver's license, and C1 is the manual transmission driver's license. Comparatively, the C2 test is simpler and easier to pass because many people struggle with mastering the clutch, often leading to failure in the test. However, the cost of the C2 test is higher. Obtaining an automatic transmission driver's license, like a manual transmission one, requires passing four subjects: the subject on road traffic safety laws, regulations, and related knowledge; the subject on field driving skills; the subject on road driving skills and safe civilized driving knowledge. The content of Subject 2 includes: parallel parking, reversing into a garage, right-angle turns, and curve driving. Starting from May 2021, the slope parking and starting project was removed from Subject 2 for small automatic transmission vehicle tests.
13
5
Share

Do Volkswagen cars need to add a relay when installing a reverse camera?

Volkswagen cars require a relay when installing a reverse camera, while other car models may not need one. The reason for adding a relay: German cars experience voltage and current instability when starting, with significant output voltage interference. The relay is added to protect the equipment. Function of the relay: The relay uses low power to control high current. Installing a relay allows the signal from the rear camera to be switched to the display when shifting into reverse gear, while also powering the camera. Therefore, a relay with multiple contact points is needed. During installation, only one wire from the reverse gear switch is required to control the relay to achieve this switching.
3
1
Share

What to Do When a Sedan Has Insufficient Tire Pressure?

Here are the methods to deal with insufficient tire pressure in a sedan: 1. If the tire pressure warning persists after inflation, it may be because the tire pressure has not been recalibrated. Simply recalibrate the tire pressure on the central control panel. 2. If the tire pressure warning appears some time after inflation but there is no puncture in the tire, it could be due to air leakage caused by a deformed wheel rim. It is recommended to check the wheel rim and replace it if necessary. Below are some precautions for checking tire pressure: 1. Observe the tire condition before setting off. Radial tires—commonly known as low-pressure tires—are fine as long as the aspect ratio is not too low. High-pressure tires—which are bias-ply tires with inner tubes—should not have protruding shoulder areas when viewed from the front, colloquially referred to as 'not bulging.' When viewed from the side, the contact area with the ground should be similar to normal. 2. While driving, pay attention to the sound of the tires rubbing against the ground, the cushioning effect when driving over uneven roads, and whether the acceleration feels different from usual when pressing the accelerator. 3. Under normal circumstances, check and replenish the tire pressure at a professional tire repair shop every week.
15
2
Share

Where is the fuel filter located on the BMW X1?

The fuel filter of the BMW X1 is located inside the fuel tank. Method for replacing the fuel filter: First, prepare a fuel filter suitable for the BMW X1 and remove the original fuel filter from its mounting bracket. Then disconnect the fuel inlet pipe of the fuel filter, at which point fuel inside the pipe will spill out. Direct the spilled fuel into a container. When the flow decreases, attach a hose clamp and quickly connect the new filter's fuel inlet, while also sealing the old filter's fuel inlet. Disconnect the other end of the old filter and connect it to the new filter, then tighten the hose clamp with a screwdriver to prevent fuel leakage. Finally, reinstall the replaced fuel filter back into its original position. Precautions for replacing the fuel filter: Due to the pressure within the fuel system, to avoid fuel spray or fire hazards when removing the filter, it is essential to release the pressure in the fuel system before disconnecting the fuel lines. It is advisable to perform the fuel filter replacement in the morning of the following day (when the engine is cold), as the fuel pressure in the system is lower at this time, resulting in less fuel spillage during the filter removal process.
9
1
Share

What is the headlight?

Headlights generally refer to high beams and low beams, while small lights refer to contour lights, also known as width indicator lights. Here are the relevant details: 1. Function of small lights: Small lights are mainly used during dusk, dawn, or daytime when visibility is low but no illumination is needed. Their primary purpose is to signal the position of your vehicle to other drivers, not to provide illumination; they serve as warning signal lights. 2. Function of headlights: Headlights, on the other hand, are primarily used for illumination during nighttime or in weather conditions like heavy fog or rain that require lighting. They include both high beams and low beams. 3. Difference between high and low beams: Both high and low beams are used for illumination but have distinct differences. High beams are angled higher, providing illumination over a longer distance, while low beams are angled lower with a shorter illumination range. Normally, low beams are used, but when driving above 30 km/h, high beams can be employed. Additionally, high beams offer a longer field of vision, allowing drivers to assess road conditions ahead. They can also expand the driver's visual range in foggy or rainy conditions and serve as a safety measure by alerting oncoming vehicles in poor lighting conditions. When passing through intersections at night, quickly switching between low and high beams can alert other vehicles at the intersection. Modern car headlights include low beams, high beams, width indicator lights, and turn signals, with some vehicles also equipped with fog lights.
9
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.