What are the reasons for the soft brake feeling in the Sagitar that makes it seem like it can't stop?

1 Answers
GiaFitz
07/29/25 6:28pm
The brake, as a critical component of safe driving, should be given special attention by every driver. Before each drive, you can test the working condition of the brake pedal. Before starting the engine, the brake pedal will be very hard; after the engine is normally started, the brake pedal will sink slightly. The reasons for a soft brake feeling include the following: 1. Mixed brake fluid: Using different brands of brake fluid together can reduce braking performance. 2. Air in the brake fluid: The presence of air in the brake fluid that has not been bled out. 3. Oil leakage or poor sealing: Oil leakage in the master cylinder or wheel cylinders, or poor sealing. 4. Damaged outer packaging: Damage to the external casing of the brake lines.
Was this review help?
6
3
Share
More Forum Discussions

What is the function of ABS?

ABS system functions include: During braking, ABS quickly determines the wheel lock-up state based on speed signals from each wheel speed sensor, closing the normally open input solenoid valve for the wheel that begins to lock up to maintain constant braking force. If the wheel continues to lock up, the normally closed output solenoid valve is opened, causing the braking pressure on that wheel to rapidly decrease due to the direct connection to the brake fluid reservoir, preventing the wheel from completely locking up due to excessive braking force. This keeps the braking state at the optimal point (slip rate S of 20%), achieving the best braking effect and the highest driving safety. It maximizes the effectiveness of the brakes, reducing braking time and distance; effectively prevents vehicle skidding and fishtailing during emergency braking, ensuring good driving stability; allows steering during emergency braking, providing good steering control; avoids severe friction between tires and the ground, reducing tire wear.
3
5
Share

Does the right rearview mirror show the left or right side?

The left rearview mirror is used to observe the two lanes on the left side of your vehicle. While driving, the driver should promptly monitor the traffic conditions on both sides and behind through the rearview mirrors. Below are the methods for adjusting the rearview mirrors: 1. Adjust the right rearview mirror first: The upper edge should allow you to see the rear door handle, while ensuring the front door handle is in the middle of the mirror (vertically), with the car body occupying 1/4 of the mirror area. 2. Adjust the left rearview mirror: Refer to the right rearview mirror, but note that the left rearview mirror has an additional function—during parallel parking, you need to see the left rear wheel. Make sure you can see the left rear wheel by leaning forward. For long-distance driving or highway use, adjust the left rearview mirror so that the horizon occupies half of its height, and the rear of the car is visible.
17
3
Share

What to Do If You Turn Right from a Straight Lane?

Turning right from a straight lane violates the Road Traffic Safety Law of the People's Republic of China, as it constitutes driving outside the designated lane. When passing through an intersection, motor vehicles must follow the directional lanes; otherwise, it is considered an illegal act subject to penalties, including fines and demerit points on the driver's license. Below is additional information on traffic signs: 1. Obey Traffic Signs: Motor vehicles must adhere to traffic signs on the road and follow the markings. Violations captured by surveillance cameras will result in demerit points and fines for the driver. Therefore, always pay close attention to traffic signs and markings on both sides of the road. 2. Regulations: Article 37 of the Road Traffic Safety Law of the People's Republic of China states that in lanes designated for specific vehicles, only those permitted vehicles are allowed to pass, and other vehicles must not enter these lanes.
1
3
Share

Why does the fuel pump fuse keep blowing?

There might be an issue with the fuel pump, and it is recommended to replace it promptly. Below is some extended information about the fuel pump: 1. The function of the fuel pump: It draws gasoline from the fuel tank and delivers it through the pipeline and fuel filter to the float chamber of the carburetor. It is precisely because of the fuel pump that the fuel tank can be placed at the rear of the vehicle, far from the engine, and lower than the engine. 2. Relay (English name: relay): It is an electrical control device that causes a predetermined step change in the controlled quantity in the electrical output circuit when the change in the input quantity (excitation quantity) reaches the specified requirements. It has an interactive relationship between the control system (also known as the input circuit) and the controlled system (also known as the output circuit). It is usually used in automatic control circuits and is essentially an 'automatic switch' that uses a small current to control the operation of a large current. Therefore, it plays roles such as automatic regulation, safety protection, and circuit conversion in the circuit.
5
3
Share

How to Calculate 10 Days for Booking Subject 2?

10 working days later, you can book Subject 2. Here is the relevant introduction to Subject 2: 1. Basic operations: Subject 2 requires students to master the basic driving operation essentials and possess the basic ability to control the vehicle. Proficiently master the basic methods of driving on the site and on-site roads, have the ability to reasonably use vehicle control components and correctly control the spatial position of the vehicle movement, and be able to accurately control the driving position, speed, and route of the vehicle. 2. Subject 2 test failure: According to Article 37 of the "Regulations on the Application and Use of Motor Vehicle Driving Licenses", if the applicant fails the test, they need to first pay the re-examination fee at the vehicle management office. Each subject test can be taken once, and if it fails, it can be retaken once.
13
0
Share

How to Solve the Dashboard Reflection on the Windshield?

Solutions to reflection are as follows: 1. Replace the front windshield film to improve its light transmittance: According to national standards, the visible light transmittance of the front windshield and other areas within the driver's line of sight should be greater than or equal to 70%, and no reflective film should be applied to any window glass. Films with lower light transmittance are more prone to reflection. When purchasing, you can also check the labeled light transmittance and reflectivity. 2. Purchase a dashboard sunshade mat: Placing it on the dashboard can prevent reflection. However, sunshade mats have both advantages and disadvantages, and whether to install one depends on personal preference. The pros and cons of sunshade mats are as follows: 1. Advantages: They can prevent dashboard reflection by absorbing sunlight that falls on them. 2. Disadvantages: They prevent dust from falling on the dashboard, making cleaning easier.
3
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.