What are the reasons for the SITRAK turn signal not working?

1 Answers
LilyDella
07/30/25 12:03am
Open circuit, flasher relay failure, excessive contact gap. The following is the relevant content: 1. Turn signal: The turn signal is an important indicator light that is turned on when a motor vehicle turns to alert vehicles and pedestrians in front, behind, left, and right. The turn signal bulb uses a xenon bulb, controlled by a single-chip microcomputer circuit, working continuously with alternating left and right flashes. The turn signal uses a flasher to achieve light blinking. It can be mainly divided into three types: resistance wire type, capacitor type, and electronic type. 2. Introduction to SINOTRUK SITRAK: SINOTRUK SITRAK was established in 1958 and is a provincial key state-owned sole proprietorship enterprise.
Was this review help?
6
4
Share
More Forum Discussions

How to Deal with Severe Low-Frequency Noise After Soundproofing?

Severe low-frequency noise after soundproofing is likely due to the use of incorrect soundproofing materials. It is recommended to use white sound-absorbing cotton (white cotton, Shirley cotton, ultra-fine fiber cotton), which can effectively absorb low-frequency noise waves generated externally or internally. Relevant details are as follows: 1. Avoid full coverage: If vibration damping sheets are chosen as the soundproofing material, do not opt for full coverage. While full coverage of vibration damping sheets can eliminate high-frequency noise during driving, the main noise inside the car is low-frequency noise. Therefore, using full coverage vibration damping sheets will not significantly reduce noise. 2. Counterproductive: Do not assume that more soundproofing projects will yield better results. If vibration damping sheets are applied along with additional sound-absorbing layers like white cotton, it may have the opposite effect, leading to noticeable low-frequency noise and even symptoms like dizziness and tinnitus.
7
0
Share

What is DSG Transmission Death Flashing?

DSG transmission death flashing refers to a malfunction in the DSG transmission where the gear indicator continuously flashes, gears cannot be used normally, shifting becomes difficult, and the transmission temperature rises rapidly. DSG Introduction: DSG refers to the transmission model used by Volkswagen. DSG (Direct-Shift-Gearbox) translates to 'Direct Shift Gearbox' in Chinese. Unlike conventional semi-automatic transmission systems, DSG is based on a manual transmission rather than an automatic transmission, making it a member of the AMT (Automated Manual Transmission) family.
12
5
Share

What are the causes of friction noise when turning the steering wheel of an Audi Q5?

Here are the reasons for the friction noise when turning the steering wheel of an Audi Q5: 1. Lack of oil in the shock absorber's plain bearing: Listen near the hood to determine if the noise is coming from the top mount of the shock absorber. If the noise is from the plain bearing of the shock absorber, applying some grease to the plain bearing may help. If the noise persists after greasing, replacement is necessary. 2. Loose stabilizer bar bushings: Check if the stabilizer bar bushings are loose or damaged. Loose or damaged stabilizer bar bushings can cause noise not only when turning the steering wheel but also when driving on uneven roads. Loose bushings can be fixed by adding shims, but damaged ones must be replaced.
12
2
Share

What are the symptoms of a faulty trunk lock mechanism?

Here is a relevant introduction about the symptoms of a faulty trunk lock mechanism: 1. Continuous car horn honking: The main driver's door, front passenger door, rear doors, hood lock, and trunk lock. After parking, due to improper closure or damage to the lock mechanism switch, poor contact occurs. This triggers the anti-theft system alarm after locking the car. It may be necessary to check the switch status of the four doors, engine hood, and trunk lid, and perform repairs or replacements if needed. 2. Warning light on the dashboard: The normal state is that the light turns on when the power is connected. If it turns off after three or four seconds, it indicates the engine is normal. If the light remains on after the engine starts, it indicates an engine fault, and it is necessary to check whether it is related to a faulty trunk lock.
19
2
Share

Can I withdraw from driving school directly at the vehicle management office?

Withdrawal from driving school cannot be processed at the vehicle management office; you need to go to the driving school to complete the withdrawal procedures. The following are the relevant details about withdrawing from driver's license application: 1. Personal application: If the applicant voluntarily gives up applying for a driver's license or is unable to complete the tests within the specified period due to long-term illness, military service, imprisonment, etc., the applicant should go to the local vehicle management office, fill out the "Motor Vehicle Driver's License Business Withdrawal Application Form", and submit the original and a copy of their ID card. 2. Withdrawal due to legal reasons: The vehicle management office uses the test backlog clearing analysis and judgment system to count the data of expired test permits daily and withdraws them in a timely manner according to the serial numbers. If it is found during work that the applicant has passed away, already obtained a driver's license, or their ID number has been cancelled, the accepting staff at the vehicle management office's business window will fill out the "Application Form" and report it to the responsible business supervisor for review before processing the withdrawal.
19
0
Share

Can I Make an Appointment and Take the Subject 2 Driving Test by Myself?

Subject 2 can be scheduled and taken independently. However, it is essential to communicate with your driving instructor before making the appointment. This ensures that you have completed the required training hours to be eligible for the Subject 2 test and helps the instructor manage the exam schedules and venue arrangements for all students. Here are the details about Subject 2: The full score for Subject 2 is 100 points, with evaluation criteria including failing, deducting 20 points, deducting 10 points, and deducting 5 points. For large buses, trailers, city buses, medium buses, and large trucks, a passing score is 90 points; for other vehicle types, a passing score is 80 points.
10
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.