What are the reasons for the red battery warning light?

1 Answers
PaisleeLynn
07/29/25 3:43pm
The reasons for the red battery warning light are: 1. The battery itself has aging or power loss issues; 2. During the use of the battery, the battery terminals become loose or oxidized; 3. The generator belt or tensioner is too loose; 4. The generator voltage regulator or excitation circuit is faulty. The solutions for the red battery warning light are: 1. Replace the battery in time; 2. Clean or tighten the battery terminals; 3. Replace the belt or adjust the tensioner; 4. Inspect and replace the generator. The working principle of the battery is that during charging, external electrical energy is used to regenerate the internal active material, storing electrical energy as chemical energy. When discharging is needed, the chemical energy is converted back into electrical energy output.
Was this review help?
11
3
Share
More Forum Discussions

Does the Mercedes Vito Fuel Pump Require Removing the Fuel Tank?

Mercedes Vito fuel pump requires removing the fuel tank. Fuel Pump: As the most fundamental component in the engine fuel supply system, the fuel pump is responsible for extracting fuel from the fuel tank during engine operation, delivering it continuously at a certain pressure through the fuel supply line to the engine. The high-pressure fuel pump then performs secondary pressurization and supplies a measured amount of fuel to each cylinder according to the engine's firing order. Reasons for Insufficient Fuel Pump Pressure: Wear of the oil seal at the rear end of the fuel pump drive gear shaft or loose pipeline connections, leading to air in the pipeline; insufficient fuel in the tank, dirty filter, wear or jamming of the fuel pump gear end face bearing, resulting in excessive axial clearance of the fuel pump gear. Damage to the needle bearing causes abnormal meshing of the fuel pump gears, and the inner cavity of the fuel pump housing is scratched.
14
0
Share

What is the normal tire pressure range for Haval M6 in summer?

Haval M6's normal tire pressure range in summer is between 2.4bar and 2.8bar. If the car is often parked outdoors, the tire pressure can generally be about 0.1bar lower than the standard to avoid tire blowouts due to high temperatures. The hazards of excessive tire pressure are as follows: Tire friction and adhesion will decrease, affecting braking performance; it can cause steering wheel vibration and deviation, reducing driving comfort; it accelerates localized wear on the central tread pattern of the tire, shortening tire lifespan; increased body vibration indirectly affects the lifespan of other components; it causes excessive stretching deformation of the tire cords, reducing tire elasticity and increasing the load on the car while driving; puncture resistance decreases. When encountering sharp objects like nails or glass on the road, they can easily penetrate the tire, and impacts can cause internal cracks and explosions, leading to tire blowouts. The hazards of insufficient tire pressure are as follows: Friction coefficient with the road surface increases, leading to higher fuel consumption; it makes the steering wheel heavy and prone to deviation, among other factors detrimental to driving safety; it increases the movement of various parts of the tire, causing abnormal heat due to excessive rolling; it reduces the functionality of the cords and rubber, leading to delamination or cord breakage, and excessive friction with the rim causing damage to the bead area and abnormal wear; friction between the tire and the ground multiplies, causing a sharp rise in tire temperature, softening the tire, and drastically reducing its strength. High-speed driving can lead to tire blowouts; it increases tire body deformation, making the tire side prone to cracks, while generating flexing motion, leading to excessive heat, accelerating rubber aging, cord fatigue, and breakage, and also increasing the tire's contact area with the ground, accelerating shoulder wear.
20
2
Share

Why can't the Volkswagen parking brake failure start?

Volkswagen parking brake failure cannot start because the brake light switch has a problem, causing the ECU to not receive the normal start power signal. The following are the solutions to the Volkswagen parking brake failure and the usage of the parking brake: Solutions to Volkswagen parking brake failure: Replacing the brake light switch can solve the problem. This issue usually occurs in automatic transmission models, as the brake light switch also has the function of providing start power signal feedback. The parking brake is commonly called the handbrake, and its function is to provide resistance to the car when parking to prevent the car from rolling. Usage of the parking brake: When performing the parking brake, step down on the brake pedal and pull the parking brake lever all the way up. To release the parking brake, step down on the brake pedal, slightly pull the parking brake lever up, press the button on the handle end with your thumb, and then lower the parking brake lever to its original position. When parking on an inclined surface, if you shift to P position first and then perform the parking brake, the weight of the car will make it difficult for the driver to shift out of P position when preparing to start the car. When preparing to start the car, shift the gear lever out of P position before releasing the parking brake.
5
3
Share

Where is the VIN rubbing location for Chery Rely V5?

Chery Rely V5's VIN rubbing is located below the wiper arm in the engine compartment. Below are the VIN rubbing location and related introduction of Rely V5: Chery Rely V5 VIN rubbing location: It is below the wiper arm in the engine compartment. You can see the VIN after removing the plastic cover. However, the VIN of most vehicles is located in the engine compartment or under the left front windshield, which is easy to find. Related introduction of Rely V5: Rely V5 is an MPV model. This car uses three engines in total: a 1.8L naturally aspirated engine, a 1.9L diesel turbocharged engine, and a 2.0L naturally aspirated engine. The 2.0L naturally aspirated engine has a maximum power of 139 horsepower and a maximum torque of 182 N·m. This engine can output maximum power at 5750 rpm and maximum torque at 4300-4500 rpm. This engine is equipped with multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. The 1.9L turbocharged diesel engine has a maximum power of 126 horsepower and a maximum torque of 271 N·m. This engine can output maximum power at 4000 rpm and maximum torque at 2000 rpm. This engine is equipped with direct injection technology and uses a cast iron cylinder head and block.
5
0
Share

Reasons for Reduced Engine Oil in Dongfeng Peugeot Vehicles in Summer

Reasons for reduced engine oil in Dongfeng Peugeot vehicles during summer: aging of cylinders, pistons, or piston rings; weakened sealing of valve guides; aging of engine body sealing rings leading to reduced sealing; loose oil pan screws. Definition of Engine Oil: Engine oil, also known as motor lubricant, serves to lubricate and reduce friction in the engine, assist in cooling, provide sealing to prevent leaks, protect against rust and corrosion, and act as a shock absorber. Composition of Engine Oil: Engine oil consists of base oil and additives. The base oil is the main component of the lubricant, determining its basic properties. Additives are used to compensate for and improve any deficiencies in the oil's performance, and it is categorized into diesel engine oil and gasoline engine oil.
12
0
Share

How to reset the tire pressure warning in the TACQUA?

TACQUA tire pressure monitoring light reset method: Turn on the ignition, press and hold the SET button of the tire inflation pressure control system. The tire monitoring button is located on the black button on the front panel near the gear shift lever until the instrument indicator light comes on. The tire pressure monitoring indicator is a yellow symbol, an irregular circle with no seal on top and four small spikes at the bottom, containing an exclamation mark inside. The tire pressure monitoring indicator light indicates abnormal tire pressure. There are generally three reasons for abnormal tire pressure in the TACQUA: Abnormal tire pressure: Usually, it will trigger an alarm if the pressure is below 1.8bar or above 3.0bar. At this time, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset in time, the tire pressure monitoring system will still record the original data, causing the tire pressure monitoring indicator light to come on. Simply perform a tire pressure reset at this time. Damaged tire pressure sensor: The tire pressure sensor is used to monitor tire pressure and is directly installed inside the tire, connected to the tire inflation port. If the tire pressure sensor is damaged during driving, it will also cause the tire pressure fault light to come on. For sensor damage issues, only a brand new replacement can be installed.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.