What are the reasons for the Nissan Qashqai wiper not spraying water?

Where is the cabin air filter located in a BMW 320i?

The cabin air filter in a BMW 320i is located inside the glove compartment on the passenger side. Below are the steps for replacing the cabin air filter: 1. Open the glove compartment and remove the fuse box cover. 2. Detach the spring cord buckle, then forcefully pull upward to remove the plastic crossbeam above the glove compartment. 3. Squeeze both sides toward the center to completely remove the glove compartment, exposing the cabin air filter housing. 4. Unclip the buckles on both sides to open the housing cover, then remove the old filter and install the new one before reassembling in reverse order. Below are the functions of the cabin air filter: It minimizes the entry of unfiltered air into the vehicle cabin. It filters out solid impurities such as dust, pollen, and abrasive particles from the air, while also absorbing harmful substances and moisture. Additionally, it ensures clean air in the passenger compartment and prevents bacterial growth.

3

1

Share

Can the position lights and low beam lights be turned on together?

Position lights and low beam lights cannot be turned on simultaneously. Here are the relevant details: 1. When turning on the low beam lights, the design requires first activating the position lights, then the low beam lights. The first turn of the control lever activates the position lights, and the second turn activates the low beam lights. Therefore, when the low beam lights are on, the position lights are already activated. 2. Generally, regulations stipulate that vehicles with a body height exceeding three meters must be equipped with position lights, and vehicles with a width greater than 2.10 meters must also have them. For close-range illumination, the design requires low beam lights to have a wide coverage (160°) but a short illumination distance, approximately 30-40 meters. 3. When driving at night at a speed of 55 km/h, if a situation is detected and the brakes are immediately applied, the stopping distance is exactly 30 meters. This means that the safe distance for seeing an obstacle within the low beam light's range and braking immediately at night is 30 meters, with the speed generally controlled at 40 km/h.

8

5

Share

How to Solve the Problem of Abnormal Brake Noise After a Car Goes Through Water?

If the car has not gone through deep water, it is normal to hear a squealing sound when braking. This situation will resolve itself as long as you drive normally and wait for the water on the brake pads to dry. Foreign objects such as plastic bags, paper scraps, and mud in the water can get stuck on the brake pads, causing abnormal noise when braking. Cleaning the brake pads will solve this issue. Check the brake calipers for issues such as worn guide pins or detached spring plates. If any faults are found, promptly visit a repair facility for servicing. Normally, brake pads come with a warning metal pin. When the brake pads wear down to a certain extent, this pin will rub against the brake disc, producing abnormal noise.

6

5

Share

How to Disable the Anti-Theft System on a Buick Regal?

To disable the anti-theft system on a Buick Regal, follow these steps: 1. Turn the key to the "ON" position and wait until the anti-theft light flashes, then turn the key back to the "OFF" position. 2. Repeat the process: turn the key to the "ON" position again, wait for about 10 minutes until the anti-theft light flashes once more, then turn the key back to the "OFF" position. Perform this sequence three times in total to successfully disable the anti-theft system. Here is some additional information about the anti-theft system: 1. Most vehicle anti-theft systems contain an integrated chip with certain switch gates. When triggered by voltage, these switch gates open and output a positive voltage to the driving circuit, activating the actuator and alarm circuit. 2. The radio remote control is a crucial component of the anti-theft system. It is a remote control device that uses radio signals to operate various mechanisms from a distance.

3

2

Share

What is the purpose of the driver's armrest?

The functions of the driver's armrest: 1. It allows the driver to effectively relieve arm fatigue during long drives, preventing numbness, stiffness, and soreness, thereby reducing the occurrence of traffic accidents; 2. It serves as storage space, a rear ashtray, or a place to hold cups; 3. It can be used to charge devices such as smartphones and tablets. The driver's armrest is an automotive accessory installed between the two front seats in the driver's cabin. Components of the driver's armrest: 1. Lid: The lid is connected to the main body, and opening it allows small items like drinks or phones to be placed inside; 2. Main body: Primarily composed of internal panels and an outer covering, the internal panels provide excellent compression resistance, while the outer layer is often made of leather, offering a soft texture and an aesthetically pleasing appearance; 3. Base: Depending on the installation method, it can be categorized into clip-on and plug-in types. The clip-on type involves securing the base onto the cup holder during installation, making it less prone to detachment, while the plug-in type involves inserting the base directly into the cup holder's hole for fixation.

1

0

Share

Where is the cabin air filter located in the old Teana model?

The cabin air filter in the old Teana model is located behind the glove box on the passenger side. When replacing the cabin air filter, pay attention to the arrow direction on the filter, which should face upwards because the evaporator is positioned above, and air passes through the filter first before entering the evaporator. More details are as follows: 1. When replacing the cabin air filter, refer to the shape of the old Teana's filter. Press the new filter into a "()" shape, insert one corner first, then the other corner, so the inner edge can be properly fitted. 2. Adjust the filter's position by gently pulling and pushing it a few times, then start inserting the outer edge, also one corner at a time, until the entire edge is smoothly embedded. Pull and push it a few more times to adjust the position. 3. The Nissan Teana cabin air filter purifies the air entering the vehicle interior from outside, improving air cleanliness. It typically filters impurities in the air, such as tiny particles, pollen, bacteria, industrial exhaust, and dust. 4. The cabin air filter prevents these substances from entering and damaging the air conditioning system, provides a good air environment for passengers, protects their health, and also helps prevent windshield fogging.

14

4

Share

What are the reasons for the Nissan Qashqai wiper not spraying water?

Where is the cabin air filter located in a BMW 320i?

Can the position lights and low beam lights be turned on together?

How to Solve the Problem of Abnormal Brake Noise After a Car Goes Through Water?

How to Disable the Anti-Theft System on a Buick Regal?

What is the purpose of the driver's armrest?

Where is the cabin air filter located in the old Teana model?

How to parallel park between two cars?

Why can't the Haval F7 trunk be opened with the remote control?

Hidden Features of the 2021 BMW X1

How to Downshift from 5th Gear When Encountering a Red Light in a Manual Transmission Car?