What are the reasons for the failure of the fuel pressure sensor function in the Volkswagen Magotan?

1 Answers
DiEmilia
07/29/25 10:07pm
Volkswagen Magotan fuel pressure sensor function failure reasons are as follows: Alarm line poor contact: For the Volkswagen fuel pressure sensor function failure, first check whether the alarm line connection is poorly contacted or has interference. Sensor failure: Check the high and low fuel pressure at idle. Possible causes include intake pipe throttle position sensor and its circuit failure, vacuum line leakage, or engine control unit damage. It is recommended to visit a professional repair shop for diagnosis and repair. Fuel pressure sensor malfunction: If the low-pressure fuel pressure sensor fails, the fuel pressure pre-adjustment will replace the fuel pressure regulation. The fuel pressure will be approximately 6.5 bar. If the low oil pressure is insufficient for a long time, it may cause abnormal wear of the fuel pressure regulating valve, leading to sticking and ultimately resulting in the failure of the fuel pressure sensor function.
Was this review help?
12
5
Share
More Forum Discussions

What is the steering wheel handling mantra for beginners?

New drivers should follow this steering wheel handling mantra: Left hand at the 9 o'clock position, right hand between 3-4 o'clock position, with the thumb gripping the inner side of the wheel and the other four fingers holding the outer side. Below is relevant information about steering wheels: 1. Function: The steering wheel is typically connected to the steering column via splines. Its purpose is to convert the force applied by the driver on the wheel's edge into torque transmitted to the steering column. Larger diameter steering wheels require less hand force from the driver during turns. The steering intermediate shaft serves as a connector between the steering gear and steering column, facilitating steering gear standardization while compensating for manufacturing and installation errors, enabling more rational installation of steering components in vehicles. 2. Fault diagnosis: Drive at approximately 15 km/h on open roads while making left and right turns to check steering responsiveness. Verify whether the wheel returns to center properly and if the vehicle drifts when releasing the wheel.
15
0
Share

What are the precautions for gear shifting in Subject 3?

Precautions for gear shifting in Subject 3 are as follows: 1. Depress the clutch and release the accelerator: The cause of imbalance is the incorrect sequence of depressing the clutch and releasing the accelerator. If the accelerator is released before the clutch is depressed, the engine stops supplying fuel while the clutch is not disengaged, which may lead to "engine braking" or a "jerking" sensation. 2. Gear shifting: This is the substantial step in the entire gear shifting process. After the RPM is synchronized, the two gears will engage smoothly, so this step will not cause any impact. 3. Release the clutch and press the accelerator: This is the stage most prone to impact, and the control of releasing the clutch is crucial.
12
5
Share

When slowing down, should you press the clutch or the brake first?

When slowing down, you should press the brake first. Below are incorrect ways to pass speed bumps: 1. Not slowing down when passing speed bumps: If the driver consistently passes speed bumps at high speed, it will cause greater impact on the vehicle, accelerate the wear of the tire tread rubber, and may lead to the car pulling to one side. 2. Passing speed bumps at an angle: When passing speed bumps at an angle, the two wheels do not press the speed bump simultaneously, causing the front of the car to tilt. Passing speed bumps at an angle over the long term will significantly affect the car's suspension, easily causing uneven force distribution on the left and right suspension, and result in greater wear and tear on the springs, shock absorbers, and the entire body.
10
2
Share

What year does the VIN code F represent?

VIN code F represents a vehicle from the year 2015. Below is relevant information about VIN codes: 1. Definition: The Vehicle Identification Number, abbreviated as VIN, is a unique set of seventeen letters or numbers assigned to a vehicle, used to identify the manufacturer, engine, chassis number, and other specifications of the vehicle. 2. Manufacturer: The first three digits of the VIN are known as the WMI (World Manufacturer Identifier), used to identify the manufacturer's name and country of origin. For manufacturers producing fewer than 500 vehicles annually, the third digit of the VIN will be a '9', and digits 12-14 will serve as the second part of the identification. 3. Plate Location: Except for trailers and motorcycles, the VIN plate should be affixed to the door hinge pillar, door lock pillar, or one of the door edges adjacent to the door lock pillar, near the driver's seating position.
11
0
Share

What car has the character 'Song' as its logo?

The car with the character 'Song' as its logo is from the BYD brand, specifically the Song model. The fuel version of the Song has a guide price ranging from 79,800 to 119,800 RMB, positioning it in the entry-level to mid-range consumer segment, where there are few outstanding models, and the Song is one of them. Details about the fuel version of the Song: 1. Body dimensions are 4600*1830*1700 mm with a wheelbase of 2600 mm, making it a compact SUV. It offers reasonable cabin space and ample expansion space, with a maximum trunk depth of 1.86 meters that is mostly flat, providing high practicality. 2. It is powered by a 1.5T direct-injection turbocharged engine, delivering a maximum power of 113 kW and peak torque of 240 Nm. It is paired with either a 6-speed manual or a 6-speed wet dual-clutch transmission, offering performance and fuel efficiency that are top-tier for its class and price range. Safety features include standard ESP (Electronic Stability Program), with a suspension system consisting of front MacPherson struts and rear multi-link independent suspension, ensuring a satisfactory level of safety and driving comfort.
9
0
Share

When is the implementation date of the China VI emission standard in Shanghai?

Shanghai implemented the China VIa standard on July 1, 2020, and the China VIb standard on July 1, 2023. The following are the differences between China V and China VI standards: 1. Different carbon monoxide emission requirements: China V vehicles have a carbon monoxide content of 1000mg per kilometer, while China VI vehicles have a carbon monoxide content of 500mg per kilometer. 2. Different implementation times: The China V standard was implemented nationwide on January 1, 2017, as the fifth stage of the national motor vehicle emission standard. The China VI standard has been implemented since July 1, 2019. 3. Different principles: During the China V stage, diesel vehicles had different emission standards, but China VI adopts a fuel-neutral principle.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.