What are the reasons for the excessive abnormal noises in the Citroën C6?

2 Answers
DelCourtney
07/29/25 6:20am
The reasons for the excessive abnormal noises in the Citroën C6 are as follows: 1. Transmission noise: If the car makes abnormal noises while idling, and the noise disappears when the clutch is pressed, it indicates that the noise is caused by a transmission malfunction. Transmission noise is generally caused by bearing or gear wear. 2. Engine compartment noise: Some sounds from engine vibrations are normal, but there are special cases, such as the sharp screeching of a belt, which is usually caused by belt slippage. 3. Steering wheel noise: If abnormal noises occur when turning the steering wheel left or right, it is generally caused by an abnormal steering mechanism. Among these, friction due to aging of the steering tie rod and ball joint rubber sleeve is the most common cause.
Was this review help?
6
5
Share
AutumnAnn
08/12/25 9:47am
As a long-time owner of the Citroën C6, I frequently encounter various squeaking issues, especially on bumpy roads. Aging interior panels are the main culprit—door and dashboard plastic parts tend to loosen over time, causing rattling noises when they collide. Poorly secured air vents or glove compartments are also common annoyances. Then there’s the suspension system—worn shock absorbers or springs can produce clunking sounds over speed bumps. Overall, the Citroën C6 is a comfortable ride, but the constant noises are frustrating and ruin the driving experience. I recommend regularly checking interior fastening screws and adding some cushioning pads for improvement. Excess clutter in the car can amplify noises, so try clearing items under the rear seats. Generally, these are common issues with older cars—until you upgrade, you’ll just have to tolerate them.
Was this review help?
19
1
Share
Expand All
More Forum Discussions

What is the solution for windshield leakage?

Carefully remove the windshield, clean off the original sealing material, and repair any damaged areas. Clean the upper edge of the glass thoroughly, sand down the leaking area, and dry it with an air gun. Reinstall the windshield using new sealant, paying attention to waterproofing. Use transparent tape to secure the edges of the windshield for fixation, and remove the tape after 12 hours.
20
1
Share

How to Use Buick In-Car WiFi?

Purchase an in-car WiFi router from a 4S store, which will serve as the in-car WiFi hotspot. The charging interface can be connected to the cigarette lighter. Apply for a 4G wireless data card at a mobile or telecom service center, then insert the data card into the router's 4G card slot. Turn on your phone's WiFi and search for the signal on your device. The router is encrypted by default, so find the initial password in the instruction manual.
16
5
Share

How to Issue a Company Invoice for Fueling?

If the consumer pays through the gas station's app, there will be an option to issue an invoice on the payment success page. The consumer only needs to fill in the company name and tax identification number. If the consumer pays on-site with cash, bank card, or a third-party payment platform, they can apply to the gas station staff. Provide the personal mobile phone number and other invoice information to the staff, who will then send the processed electronic invoice to the consumer's phone.
5
2
Share

How to Determine the Parking Point on a Slope?

Use the wiper as a reference point. When the protrusion on the wiper, the parking marker pole, and your line of sight align in a straight line, apply the brakes. If you're unsure about the distance for any reason, it's better to stay more than 30cm away than to cross the roadside line. When the car starts to vibrate after releasing the clutch with your left foot, slowly release the brake with your right foot. Avoid releasing the brake too quickly, and keep the clutch steady.
4
5
Share

How to Remove the Front Bumper of a Beidou Star?

Pry open the clips on the grille, then hold the left and right sides of the front grille with your hands and gently pull outward to separate the front grille from the front bumper. Remove the screws on the top, bottom, left, and right sides of the front bumper. Take out a flat-head screwdriver and use it to pry open the clips that secure the left and right sides of the front bumper. Hold the corners of the front bumper with your hands and gently pull outward to separate the front bumper from the vehicle body. Then, disconnect the wiring harness connectors for the fog lights on both sides.
5
3
Share

How to Replace the Engine Belt?

Loosen the generator fixing screw and the belt tension adjustment screw. Align the ignition marks of the crankshaft and camshaft. Push the generator close to the engine to minimize the distance between the pulleys, then place the belt in position and straighten it. Adjust the belt tension to the appropriate level. If it is too loose or too tight, make timely adjustments, then tighten the engine fixing screw and adjustment screw.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.