What are the reasons for the engine not starting?

2 Answers
DelJessica
07/24/25 8:50am
The reasons for the engine not starting are: 1. The battery is dead; 2. The gear is not in the correct position; 3. Faulty spark plugs, circuits, or fuel filters; 4. Engine carbon buildup; 5. The steering wheel is locked; 6. Water in the engine. The solutions for the engine not starting are: 1. Charge the battery; 2. Return the gear to the correct position; 3. Replace the spark plugs, circuits, fuel filters, or engine; 4. Clean the engine; 5. Engage first gear and slowly release the clutch to use the turning force of the wheels to drive the engine flywheel; 6. Position the fronts of two cars facing each other, connect the positive and negative clamps to the respective terminals of the two car batteries for a jump start.
Was this review help?
17
0
Share
AryaMarie
08/11/25 4:18am
Answer 1: As a veteran driver with twenty years of experience, I've encountered countless cases of engines failing to start. The most common issue is a dead battery—when you turn the key and the dashboard doesn't light up, it's usually because the battery has reached the end of its lifespan or the lights were left on, draining the power. Next are fuel system problems, such as a faulty fuel pump failing to deliver fuel or an empty gas tank (something I've done myself). Thick carbon buildup on spark plugs causing ignition failure is particularly common in older vehicles, and a faulty starter often produces a clicking or whirring sound. A dirty throttle body restricting airflow can also make starting difficult, especially if the air filter hasn't been replaced in two years. Oh, and an anti-theft system malfunction can lock the engine—using the wrong key or a faulty sensor module can trigger this. Voltage instability due to alternator failure or blown fuses in the electrical system are also worth checking. If you're troubleshooting yourself, start with the battery and fuel tank. If all else fails, call for a tow truck immediately.
Was this review help?
4
3
Share
Expand All
More Forum Discussions

What is the adjustment method for valve clearance in a single-cylinder diesel engine?

The adjustment method for valve clearance in a single-cylinder diesel engine is as follows: 1. Remove the cylinder head cover when the engine is cold; 2. Rotate the flywheel to align the top dead center mark on the flywheel with the pointer mark on the radiator, positioning the piston at the top dead center of the compression stroke; 3. Measure the clearance between the end of the valve stem and the rocker arm. If a feeler gauge cannot be inserted or there is still a significant gap after insertion, the valve clearance needs to be adjusted; 4. Loosen the lock nut of the valve clearance adjustment screw, turn the adjustment screw, and measure with a feeler gauge until the measured value matches the specified value. While keeping the adjustment screw stationary, tighten the nut.
7
4
Share

Which is better, reversing camera with trajectory or without trajectory?

Reversing camera with trajectory is better. Here are some related introductions about reversing cameras: 1. Introduction to reversing cameras: Reversing cameras, also known as parking assist systems, or reversing visual systems, vehicle monitoring systems, etc. English name: vehicle-backup-camera. This system is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Advantages of reversing cameras: Simple installation. Generally, a single-output reversing camera only requires connecting the positive power wire to the positive terminal of the vehicle's reversing light power, and the negative power wire to the negative terminal of the reversing light or to ground (GND). The wiring can be easily figured out based on the vehicle model, and the camera can be installed in an easy-to-mount position by drilling a hole.
10
2
Share

What do the three colors in the reversing camera represent in terms of distance?

Green indicates a distance of 1 to 3 meters, yellow represents a distance of less than 1 meter, approximately between 60 to 100 centimeters, and when approaching red, the distance is reduced to 60 centimeters. Below is relevant information about the reversing camera: 1. Introduction to the reversing camera: The reversing camera, also known as a parking assist system, or vehicle backup monitoring system, is referred to in English as: vehicle-backup-camera. This system is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Advantages of the reversing camera: Installation is simple; generally, a standard single-output reversing camera only requires connecting the positive power wire to the positive terminal of the vehicle's reversing light power and the negative power wire to the negative terminal of the reversing light or to ground (GND). Wiring can be easily understood with a simple study based on the vehicle model, and the camera can be installed by drilling a hole in an easily accessible position.
15
3
Share

What to Do When the Reversing Camera Changes from Wide Angle to Fisheye?

Just clean it. Below is relevant information about the reversing camera: 1. Introduction to the reversing camera: The reversing camera, also known as a parking assist system, reversing visual system, or vehicle monitoring system, is referred to in English as: vehicle-backup-camera. This system is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Advantages of the reversing camera: Simple installation. Generally, a standard single-output reversing camera only requires connecting the positive power wire to the positive terminal of the car's reversing light power and the negative power wire to the negative terminal of the reversing light or to ground (GND). The wiring can be easily figured out based on the vehicle model, and the camera can be installed by drilling a hole in an easily accessible position.
20
5
Share

Why is the reversing camera shaking?

The phenomenon of horizontal stripes shaking in the reversing camera is most likely due to poor contact in the wiring. Below is relevant information about the reversing camera: 1. Introduction to the reversing camera: The reversing camera, also known as the parking assist system, or backup visual system, or vehicle monitoring system. English name: vehicle-backup-camera. This system is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Advantages of the reversing camera: Simple installation. Generally, a standard single-output reversing camera only requires connecting the positive power wire to the positive terminal of the vehicle's reversing light power, and the negative power wire to the negative terminal of the reversing light or to ground (GND). The wiring can be easily understood based on the vehicle model, and the camera can be installed by drilling a hole in an easily accessible position.
11
5
Share

How to reset the vehicle condition check for the Volkswagen New Passat?

To reset the vehicle condition check for the Volkswagen New Passat, follow these steps: 1. Turn on the hazard lights and long-press the time setting button; 2. Turn on the ignition, and the vehicle condition check will appear, then click to confirm. The Volkswagen New Passat is a mid-size car under SAIC Volkswagen, with body dimensions of 4933 mm in length, 1836 mm in width, and 1469 mm in height, a wheelbase of 2871 mm, a fuel tank capacity of 68.5 liters, and a trunk capacity of 521 liters. The Volkswagen New Passat is equipped with a 1.4T turbocharged engine, delivering a maximum horsepower of 150 hp, a maximum power of 110 kW, a maximum power speed of 5000 rpm, and is paired with a dual-clutch transmission.
16
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.