What Are the Reasons for the Car Dashboard Not Lighting Up and the Engine Not Starting?

How to Replace the Air Filter in a Mondeo?

Here are the steps to replace the air filter in a Mondeo: 1. Open the hood of the Mondeo and locate the air filter, which is on the right side of the engine. 2. After opening the clips and the black cover, you will see the air filter. 3. Remove the old filter and install the new one in its place, paying attention to the direction. Below is additional information about the air filter: 1. During operation, the engine inhales a large amount of air. If the air is not filtered, the dust suspended in the air can enter the cylinders, accelerating the wear of the piston group and the cylinders. Larger particles entering between the piston and the cylinder can cause severe cylinder scoring, especially in dry and sandy working environments. 2. The air filter is installed in front of the carburetor or intake pipe to filter out dust and sand particles from the air, ensuring that the cylinders receive sufficient and clean air. The air contains a lot of suspended dust, mainly composed of silicon dioxide, which is harder than metal. Installing an air filter can reduce wear on parts such as cylinders, pistons, and piston rings.

2

1

Share

What is the difference between part-time four-wheel drive and on-demand four-wheel drive?

Here are the differences between part-time four-wheel drive and on-demand four-wheel drive: 1. Different switching modes: On-demand four-wheel drive usually operates in two-wheel drive mode and automatically switches to four-wheel drive when necessary. The part-time four-wheel drive system requires manual switching between two-wheel drive, high-speed four-wheel drive, and low-speed four-wheel drive modes. 2. Different technologies: Part-time four-wheel drive allows the driver to choose between two-wheel drive or four-wheel drive mode by engaging or disengaging the transfer case. Its advantage is that it ensures both the vehicle's power and off-road capability while maintaining fuel economy. The slight drawback is that the driver needs to judge the road conditions and manually operate the drive mode. On-demand four-wheel drive uses a computer chip to control the switching between two-wheel drive and four-wheel drive. It can automatically identify the driving environment and switch between two-wheel drive and four-wheel drive modes based on changes in the driving environment. On rough, hilly, or low-traction roads, the vehicle automatically sets to four-wheel drive mode, while on flat urban roads, it switches to two-wheel drive.

1

2

Share

What License is Required for an Automatic Transmission Car?

According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses": Small automatic transmission cars require a C2 license. The C2 license covers small and micro automatic transmission passenger vehicles, as well as light and micro automatic transmission cargo vehicles. Additionally, holders of A1, A2, A3, B1, B2, or C1 licenses can also drive automatic transmission cars. Below are the age requirements for applying for a motor vehicle driving license: 1. Applicants for small cars, small automatic transmission cars, small automatic transmission passenger cars for the disabled, or mopeds must be between 18 and 70 years old. 2. Applicants for low-speed cargo vehicles, three-wheeled vehicles, ordinary three-wheeled motorcycles, ordinary two-wheeled motorcycles, or wheeled self-propelled machinery must be between 18 and 60 years old. 3. Applicants for city buses, large trucks, trolleybuses, or tramways must be between 20 and 50 years old. 4. Applicants for medium-sized passenger vehicles must be between 21 and 50 years old. 5. Applicants for tractor-trailers must be between 24 and 50 years old. 6. Applicants for large passenger vehicles must be between 26 and 50 years old.

12

4

Share

How to adjust the headlights of the Baojun 730?

Open the car door and you can see the headlight height adjustment knob on the left side of the dashboard. Turning the knob to the 0 position sets the headlights to the lowest height. Adjusting the knob to the 1 position raises the headlights slightly higher. Setting the knob to the 2 position increases the headlight height further, while the 3 position is the highest setting. Below is an introduction to car lighting: 1. Both high and low beams are used to illuminate the road ahead. The difference is that one illuminates a shorter distance while the other covers a longer range. Typically, low beams illuminate a distance of about 30-40 meters with a coverage of approximately 160°, whereas high beams are more focused, brighter, and can reach higher and farther distances. The actual illumination distance may vary depending on the headlight material. 2. Pushing the switch toward the engine compartment keeps the high beams on continuously. Pulling it back one position turns off the high beams and reverts to low beams. Pushing the switch one more position toward the driver activates temporary high beam flashing, and releasing the switch automatically returns it to the low beam position.

15

5

Share

Which engine is used in the Haval M6?

Haval M6 is equipped with a 1.5-liter turbocharged engine across the entire lineup. Here are some details about the Haval M6: 1. The Haval M6 is a compact SUV. Its 1.5-liter turbocharged engine delivers 150 horsepower and a maximum torque of 210 Nm. This engine can output maximum power at 5600 to 6000 rpm and maximum torque at 1800 to 4400 rpm. The engine features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. 2. This engine is paired with either a 6-speed manual transmission or a 7-speed dual-clutch transmission. The dual-clutch transmission offers fast shifting and high transmission efficiency, making it highly suitable for use with small-displacement turbocharged engines. The Haval M6's front suspension uses a MacPherson independent suspension, while the rear suspension employs a double-wishbone independent suspension, a common feature in many Haval models. 3. The double-wishbone independent suspension is an improved version of the double-wishbone suspension. It replaces the two wishbones of the double-wishbone suspension with two links, resulting in a simpler structure, smaller size, and reduced space occupancy. The double-wishbone suspension can minimize the vehicle's roll angle, thereby enhancing handling and ride comfort.

20

1

Share

Which year does the VIN code 'J' represent for a car?

VIN code 'J' represents a car from the year 2018, according to the VIN coding standard. The Vehicle Identification Number (VIN), also known as the car's identification code, serves as the car's unique identifier, similar to an ID card. Each car has its own distinct VIN, which consists of 17 digits or letters. Owners can extract a lot of information from the VIN, such as the place of production, vehicle type, model year, and assembly details. The rules for decoding a VIN are as follows: 1. The first three characters represent the vehicle's origin, manufacturer, and general type; 2. Characters four to eight describe the vehicle, indicating weight, chassis type, specific model, body type, and engine information; 3. Characters nine to eleven are consistent across all manufacturers, representing the check digit, model year code, and plant code; 4. The last six digits are the production sequence number.

10

5

Share

What Are the Reasons for the Car Dashboard Not Lighting Up and the Engine Not Starting?

How to Replace the Air Filter in a Mondeo?

What is the difference between part-time four-wheel drive and on-demand four-wheel drive?

What License is Required for an Automatic Transmission Car?

How to adjust the headlights of the Baojun 730?

Which engine is used in the Haval M6?

Which year does the VIN code 'J' represent for a car?

What gear should be in when waiting at a red light?

How to Use the Headlights on a BMW X1?

What is the function of urea solution for heavy trucks?

What is the sequence between handbrake and gear shifting?