What are the reasons for the Buick LaCrosse not responding when trying to start with electricity?

1 Answers
EmmanuelFitz
07/29/25 3:59pm
Buick LaCrosse not responding when trying to start with electricity could be due to the following reasons: Spark plug failure: Check the circuit to see if the spark plug is igniting normally, whether there is any leakage, and whether the high-voltage wire has a high-voltage spark. If there is an ignition coil, check if the ignition coil is faulty. Fuel line blockage: Inspect the fuel line, open the engine's fuel inlet pipe, turn the key to start, and see if fuel comes out. If no fuel comes out, it may be due to a blocked fuel line or the electronic fuel pump not working. Another rare possibility is the ECU being locked due to anti-theft activation. Wiring fault: Issues with the starter or wiring connections can also prevent the car from starting. Additionally, if the battery's starting voltage is below 9.5V, it may also cause the car to fail to start.
Was this review help?
18
5
Share
More Forum Discussions

What does a faucet symbol on the car mean?

A faucet symbol on the car is the engine malfunction indicator light. When this symbol appears, it indicates that the car's engine has a malfunction. Below are the relevant details: 1. After the engine malfunctions, it may cause unstable idling, frequent stalling, difficulty starting, reduced power, and abnormal vibrations. When the faucet symbol appears on the dashboard, immediately take the vehicle to a repair shop for professional inspection to avoid unnecessary issues. 2. There are many reasons why the engine malfunction light may come on, including engine misfire, severe carbon buildup, overheating, faulty spark plugs, or a clogged fuel system. Since engine problems can be complex, it is recommended to visit a repair shop or 4S store for professional inspection and repair.
2
1
Share

How to Steer the Wheel When Reversing into a Parking Space?

Steps for steering the wheel when reversing into a parking space are: 1. If entering from the left, turn the steering wheel to the left in advance; if the left side is narrow, delay turning the wheel to the left. 2. If entering from the right, delay turning the steering wheel to the right; if the left side is narrow, turn the wheel to the right in advance. 3. Park the car next to the parking line and align the left rearview mirror with the left line of the parking space. 4. Turn the steering wheel fully to the right, and stop the car when the body forms a suitable angle with the parking space. 5. Straighten the wheels and reverse slowly. Reversing into a parking space is a key assessment point in the driver's test, primarily evaluating the driver's ability to maneuver the vehicle in a confined space.
7
4
Share

How to Remove the ETC Device from the Car?

Steps to remove the ETC device from the car: 1. Prepare a piece of fishing line. 2. Wear a pair of rubber gloves, such as those used for dishwashing or laundry. 3. Straighten the fishing line with both hands. Pull it forcefully downward from the top of the ETC device. If it is stuck too tightly, you may need to pull several times, then use the fishing line to cut through. 4. After cutting, use a wet wipe to clean any residue left on the windshield. Below is some related information: ETC (Electronic Toll Collection) is a non-stop toll collection system used on highways or bridges. It works through dedicated short-range communication between the vehicle-mounted electronic tag installed on the windshield and the microwave antenna in the ETC lane at the toll station. This system utilizes computer networking technology for backend settlement processing with banks, allowing vehicles to pass through highway or bridge toll stations without stopping while still paying the required fees.
3
3
Share

How to troubleshoot P0170 Fuel Trim 1?

p0170 Fuel Trim 1 troubleshooting methods are as follows: 1. According to the setting conditions of the fault code, the relevant detection methods include whether the fuel pressure is correct, whether the intake and exhaust systems are leaking, and whether the air flow meter signal is normal. 2. Based on the status displayed by the oxygen sensor's voltage signal, a clogged fuel injector can lead to insufficient fuel injection [more air results in less fuel injection, making the air-fuel ratio lean, causing idle shaking and low oxygen sensor signal voltage]. 3. Air flow meter - signal deviation - cannot meet the normal air-fuel ratio formation conditions, leading to mixture imbalance. Incorrect fuel pressure - either too low or too high - will result in incorrect mixture concentration. 4. The engine ECM judges through the oxygen sensor signal voltage. If it deviates from the set value stored in the memory and meets the fault setting conditions, the corresponding fault code will be stored.
18
4
Share

Why does the car always fail to start?

There are several reasons why a car may fail to start: 1. Dead battery: When the car battery is dead, the car won't start. There are many reasons for a dead battery, such as lack of water in the battery, battery failure, or prolonged use of the air conditioning. If the car doesn't start, the first thing to check is whether there is a problem with the car battery and what the issue is, then take it to a 4S shop for repair. 2. Low temperature: In cold winter weather, cars often have trouble starting. This is because in low-temperature environments, the viscosity and rotation speed of the car's engine oil decrease, leading to reduced ignition energy from the battery and decreased molecular activity, making it difficult to form flammable gases and thus hard to start the car. 3. Carbon buildup: Carbon buildup in the car engine can cause many problems, the most common being difficulty starting the car. There are many reasons for engine carbon buildup, such as excessive water in gasoline, poor fuel quality, or poor sealing of the valve seat rings. So if the car is hard to start, it might be worth checking if there is a lot of carbon buildup in the engine and cleaning it promptly if necessary.
7
4
Share

How to Clean Cement off a Car?

Here are the methods to clean cement off a car: 1. Before it hardens, you can wet it with clean water and rinse it off, then use a towel with cleaning solution to wash it. 2. If the cement is not discovered and treated in time and has already solidified, you can use an acidic solution to clean it, such as common white vinegar. White vinegar is an acidic liquid that can effectively dissolve cement. Pour white vinegar onto the cement attached to the car, wait a few minutes for the cement to soften, and then it will be easy to clean. 3. You can also purchase cement cleaning agents for cleaning, and the cleaning method is the same as with white vinegar. Small areas of cement can be considered for self-cleaning, but if the area is large, it is recommended to go to a professional car wash shop for cleaning, as they have specialized cleaning agents and more professional cleaning techniques.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.