What are the reasons for the air conditioning fan not working in BYD F3?

1 Answers
McJayce
07/29/25 9:46pm
The reasons for the air conditioning fan not working in BYD F3 include: the air conditioning fan being stuck, poor switch contact, or blower damage. Air conditioning fan being stuck: If the air conditioning fan and filter are not cleaned for a long time, sand and other debris can enter through the front grille during driving, clogging the filter and fan, causing the fan to stop. Poor switch contact: If the air conditioning switch has poor contact or disconnected wiring, the air conditioning will not start properly, requiring timely inspection. Blower damage: There are many reasons for blower damage, necessitating professional inspection and repair at a service center. The BYD F3 is an A+ class sedan produced by BYD Auto, featuring a stylish and elegant exterior, a simple and neat interior design with fresh light-colored upholstery, and comprehensive, rich configurations.
Was this review help?
3
0
Share
More Forum Discussions

What Octane Gasoline Should an Alpha Use?

Alpha should use 92 octane gasoline, as this is the recommended fuel grade specified in the vehicle's official owner's manual. In addition to checking the appropriate gasoline grade in the owner's manual, Alpha owners can also find this information on the fuel filler cap, which is typically labeled. The choice of gasoline grade can also be determined based on the engine's compression ratio. Vehicles with a compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. For higher compression ratios, 98 octane gasoline is recommended. However, with the advent of new technologies, the compression ratio alone cannot determine the appropriate gasoline grade, as high-compression engines can be tuned to use lower-octane fuel. Other factors, such as ignition timing, turbocharging technology, and Atkinson cycle technology, also play a role. Generally, higher-octane gasoline has a higher octane rating and better anti-knock properties. For example, 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If an Alpha is occasionally filled with the wrong gasoline grade, simply switching back to the correct grade after use is sufficient. However, prolonged use of the wrong gasoline grade can have the following effects: Using a higher-octane gasoline in a vehicle designed for lower-octane fuel will not cause damage, but the increased octane rating can alter the fuel's ignition point, leading to delayed combustion in the engine. This results in reduced engine power and thermal efficiency, manifesting as poorer performance. Using a lower-octane gasoline in a vehicle designed for higher-octane fuel can cause engine knocking. The significantly lower octane rating lowers the fuel's ignition point, causing premature ignition during the compression stroke. If combustion occurs before the spark plug fires, resistance is generated during the upward stroke. This resistance makes the engine run very unevenly. Mild knocking may only increase noise without significant engine damage, but severe knocking indicates serious engine issues, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, potentially leading to cylinder scoring.
6
4
Share

What Causes the Jaguar Engine Warning Light to Illuminate?

There are primarily 7 reasons for the engine warning light to illuminate: Sensor malfunction: This refers to sensors including coolant temperature, crankshaft position, air flow, intake temperature, and oxygen sensors. When these sensors are damaged, have poor connections, or experience signal interruptions, the vehicle's ECU cannot accurately obtain engine data, triggering the engine warning light. Fuel quality issues: Failure to use the fuel and engine oil as specified by the manufacturer may cause engine wear, leading to the illumination of the warning light. Poor combustion of the air-fuel mixture: This can result in engine carbon buildup or knocking. When detected by the oxygen sensor and reported to the ECU, the warning light will illuminate as an alert. Spark plug failure, ignition coil failure, fuel pump failure, and fuel line blockages can all cause poor combustion of the air-fuel mixture. Turbocharging issues: The intake turbocharging pipeline and turbocharger can also trigger the engine warning light. The most common issue is turbocharger damage, accompanied by symptoms such as oil leaks, excessive oil consumption, reduced power, metallic noises, and blue or black smoke from the exhaust. Intake issues: Problems with the car's intake system can lead to engine pipeline blockages, and in severe cases, trigger the engine warning light. A dirty air filter that is not cleaned regularly can cause intake problems. Exhaust issues: Exhaust system malfunctions can also cause the engine warning light to illuminate. Common causes include faults in the rear oxygen sensor, catalytic converter, exhaust camshaft, and bearing shells, with the catalytic converter being the most frequent issue. Using leaded gasoline, lead or silicon-based lubricant additives, physical damage to the catalytic converter, or faults in the engine fuel supply system can easily lead to catalytic converter failure. Anti-theft system malfunction: If the car's electronic anti-theft system fails, or if the anti-theft controller does not match the engine electronic controller, the anti-theft system can prevent the engine from operating normally and trigger the engine warning light. If the engine warning light is on, follow these steps: First, check if the engine is running normally, looking for issues such as shaking or black smoke. If present, avoid restarting the engine. Note: Do not restart the engine if the red warning light is on. If the engine can be started, turn it off and wait 5-10 minutes. Without pressing the brake, press the start button once or turn the key halfway to the 'on' position without pressing the clutch. The car will perform a self-check upon powering up. After 5-10 seconds, observe whether the warning light on the dashboard turns off. If the warning light remains on, visit a service station as soon as possible. The service station can use a portable diagnostic tool to read the fault code, identify the issue, and perform targeted repairs.
9
0
Share

Which car brand features a lion emblem?

The lion emblem represents Dongfeng Peugeot automobiles. Taking the Peugeot 4008 as an example, it belongs to the compact SUV category with the following dimensions: length 4510mm, width 1850mm, height 1628mm, wheelbase 2646mm, front track 1579mm, rear track 1587mm, fuel tank capacity 53 liters, and trunk capacity 461 liters. The Peugeot 4008 is equipped with a 1.6T turbocharged engine delivering maximum power of 170PS (125kW) and peak torque of 250Nm, paired with a 6-speed automatic transmission.
2
3
Share

What brand is the Outlander?

Outlander is a vehicle from the Mitsubishi brand. Below are the relevant details: Dimensions: The Outlander model has a body length of 4705 mm, a width of 1810 mm, a height of 1710 mm, a wheelbase of 2670 mm, and the vehicle's body structure is a 5-door, 5-seat SUV model with a fuel tank capacity of 63 liters. Curb weight: The vehicle's curb weight is 1485 kg, 1525 kg, 1560 kg, and 1620 kg, varying depending on the vehicle configuration.
6
0
Share

What are the effects of a broken shock absorber?

The effects of a broken shock absorber are: 1. During vehicle operation, road conditions will generate impact forces on the vehicle itself, affecting safe driving, and causing changes in driving speed and fuel consumption; 2. Damage to vehicle components; 3. Hindering the normal operation of the engine; 4. Continuous jolts causing failure in the torque connection device of the engine power output; 5. Reducing the shock absorption effect of the car, affecting ride comfort; 6. Causing abnormal noises when driving on bumpy roads, damaging the car suspension and leading to deformation; 7. Causing uneven force distribution on both sides of the tires, resulting in hindered vehicle control and tire wear or misalignment.
13
4
Share

How to Replace the Cabin Air Filter in a Classic Focus?

Classic Focus cabin air filter replacement method: 1. First, open the glove compartment cover behind the front passenger seat. 2. Locate the fixing buckle on the right side of the glove compartment and pull it outward firmly. 3. Remove the fixing buckle of the glove compartment cover to detach it. 4. Squeeze both sides of the glove compartment inward with both hands to remove it. 5. After removing the glove compartment, you can see the cabin air filter cover. Press the fixing buckles on both sides of the cover firmly to remove it. 6. Pull the old cabin air filter outward. 7. Install the new cabin air filter and reassemble in reverse order of disassembly (pay attention to the installation direction of the cabin air filter).
4
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.