What are the reasons for severe shaking of the BMW 5 Series when cold?

1 Answers
SanBeau
07/30/25 3:18am
BMW 5 Series severe shaking when cold is caused by: 1. Excessive carbon buildup in the throttle body, fuel injectors, or intake ducts; 2. Mechanical faults in components such as ignition coils, spark plugs, or fuel injectors; 3. Low oil pressure or cylinder pressure, leading to insufficient power; 4. Substandard fuel quality; 5. Damaged or excessively dirty idle control valve. The BMW 5 Series has a body length of 5106mm, width of 1868mm, height of 1500mm, and a wheelbase of 3105mm. It is equipped with a 2.0T turbocharged engine, paired with an 8-speed automatic transmission. The front suspension type is a double-wishbone independent suspension, and the rear suspension type is a multi-link independent suspension.
Was this review help?
18
2
Share
More Forum Discussions

What does Volkswagen fault code p0343 mean?

Volkswagen fault code p0343 indicates an issue with the camshaft sensor signal. Below is relevant information about fault code p0343: 1. Solution: First, it is necessary to confirm whether the timing system is installed correctly. Check if there is any tooth skipping in the timing system and observe whether the control components of the variable timing system are functioning properly. Also, inspect the actuator for any sticking or poor operation. If all the above checks are normal, the sensor should be replaced. After replacement, the fault code must be cleared. 2. Function of the camshaft: The camshaft is used to control the opening or closing of the valves. According to the instructions from the engine control module, it adjusts the angle of the camshaft by altering the oil pressure of the camshaft adjuster, ensuring the valves open or close under optimal conditions. Causes of camshaft position sensor failure include faults in the camshaft position sensor circuit.
11
0
Share

What is the officially recommended engine oil for Volkswagen EA211?

The officially recommended engine oil for Volkswagen EA211 is VW50200. You can choose brands such as Mobil 1 Silver, Castrol Magnetec, or Shell Helix Ultra. The Volkswagen EA211 engine comes in two types: MPI and TSI. The EA211 is an all-aluminum engine, and a fully synthetic 40 viscosity oil provides better protection for the EA211. Below is an introduction to the official engine oils: 1. Mobil: Better performance at high speeds, making it suitable for vehicles frequently driven on highways, but noise reduction is a weak point. 2. Castrol: More balanced overall, suitable for mixed driving conditions, with the drawback being a slightly shorter degradation period. 3. Shell: The advantages are noise reduction and cleaning performance, but it may lack power at engine speeds above 4,000 RPM.
14
1
Share

How Often Should Chassis Maintenance Be Performed?

Chassis maintenance primarily consists of three levels: primary, secondary, and tertiary maintenance: Primary Maintenance (around 5,000 km): This involves tightening and lubrication-focused maintenance tasks for vehicles that have traveled a certain mileage. It includes inspecting and tightening bolts and nuts on exposed parts of the vehicle, applying lubricant to designated areas, checking and topping up oil levels in various assemblies, and cleaning air filters. The goal is to maintain the vehicle's optimal technical condition and ensure smooth operation. Secondary Maintenance (around 10,000 km): This centers on inspection and adjustment tasks for vehicles that have covered a certain distance. Beyond the primary maintenance tasks, it involves checking and adjusting the engine and electrical equipment, dismantling and cleaning the oil pan and oil filter, inspecting and adjusting steering and braking mechanisms, and servicing front and rear wheel hub bearings. Lubricants are replenished, tires are inspected and rotated. The aim is to ensure all components, mechanisms, and assemblies function properly between two secondary maintenance intervals. Tertiary Maintenance (around 20,000 km): This involves comprehensive disassembly, cleaning, inspection, adjustment, and hazard elimination for vehicle assemblies. In addition to primary and secondary maintenance tasks, it includes engine disassembly to remove carbon deposits, sludge, and cooling system contaminants. The chassis assembly may be disassembled for cleaning, inspection, adjustment, and hazard resolution as needed. The frame and body are inspected, rust-treated, or repainted. The objective is to reinforce the normal performance of all assemblies and components, ensuring reliable operation.
9
2
Share

How to resolve the engine warning light issue in Bestune X40?

If the engine warning light is on in your Bestune X40, you can follow these steps to address the issue: First, check whether the engine is running normally and if there are any issues such as shaking or emitting black smoke. If these symptoms are present, avoid starting the engine again. Specifically, do not start the engine if the red warning light is on. If the engine can be started, turn it off and wait for 5-10 minutes. Without pressing the brake, press the start button once, or, without depressing the clutch, turn the car key halfway to the 'on' position. The car will perform a self-check after powering on. Wait for 5-10 seconds and observe whether the warning light on the dashboard turns off. If the warning light remains on, visit a service center as soon as possible to identify the cause. The service center can use a portable diagnostic tool to read the fault code, obtain fault information, and perform targeted repairs. The engine warning light is an icon resembling a water tap. It comes in two colors: yellow and red. A yellow light indicates a warning, while a red light means prohibition. When the yellow warning light is on, it means certain system parameters in the car may have exceeded the set range. The car can still be driven at this time, but some functions may be limited. When the red warning light is on, the car must be stopped immediately, the engine turned off, and driving must be prohibited until the fault is checked. Common causes for the engine warning light to turn on include: sensor failure, fuel quality issues, poor combustion of the air-fuel mixture, turbocharging problems, intake issues, exhaust problems, and anti-theft system failure.
12
1
Share

What is the model and specification of the Buick Excelle battery?

The model and specification of the Buick Excelle battery is 6QW60TY. The functions of the battery are: 1. To provide a strong starting current to the starter when starting the engine; 2. To assist the generator in supplying power to electrical equipment; 3. To charge the battery when the generator terminal voltage is higher than that of the battery. The Buick Excelle is a compact car under SAIC-GM Buick, with body dimensions of 4609mm in length, 1798mm in width, and 1486mm in height, and a wheelbase of 2640mm. The Buick Excelle is equipped with a three-spoke multifunction steering wheel, an ice-blue sport instrument panel, a fully automatic air conditioning system, a one-button start function, rear air conditioning vents, a flexible 400L luggage compartment, and other systems.
1
2
Share

Where is the oil dipstick located on the BYD Song?

The oil dipstick for the BYD Song 1.5T model is located at the rear left side of the engine, while the oil dipstick for the 2.0T model is positioned on top of the engine, both featuring yellow pull rings. The hybrid version uses an electronic oil dipstick, which can be displayed on the dashboard by pressing the function button on the steering wheel. Types of engine oil: Semi-synthetic oil is one type of engine oil. It is formulated using semi-synthetic base oil, specifically Group III base oil, and is a lubricant refined from mineral oil through hydro-cracking technology. It offers slightly better performance than mineral oil and serves as an ideal transitional product between mineral oil and fully synthetic oil. Fully synthetic oil has a wider operating temperature range and a longer service life. For the same oil film requirements, synthetic oil can achieve the desired performance with lower viscosity, whereas semi-synthetic oil requires a higher viscosity to meet the same standards. Conventional mineral oil consists of base oil and additives. The base oil is the primary component of the lubricant, determining its general properties, while additives compensate for and improve the shortcomings of the base oil, providing certain new characteristics. Additives are a crucial component of lubricants.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.