What are the reasons for regular car maintenance?

1 Answers
McCarlos
07/30/25 6:47am
The reasons for regular car maintenance are: 1. Keep the car clean and tidy; 2. Ensure normal technical conditions; 3. Eliminate hidden dangers and prevent failures; 4. Slow down the deterioration process and extend the service life. The scope of regular car maintenance includes: 1. Replace engine oil, oil filter, gasoline filter, and air filter; 2. Check whether the liquid level of the car coolant meets the regulations; 3. Check the liquid level of the brake and clutch; 4. Check whether the oil level of the power steering oil tank meets the regulations; 5. Check whether there is oil leakage at each oil pipe interface of the system; 6. Check the liquid level of the battery and the glass cleaner tank; 7. Check the tightness and aging of the generator, air conditioner, water pump, and power pump belts; 8. Check whether the front and rear lights of the car are complete; 9. Check the tire pressure and wear condition of the car; 10. Check whether the car's exhaust emissions meet the standards.
Was this review help?
17
3
Share
More Forum Discussions

What is the actual measured ground clearance of the Envision?

The Envision model comes with two ground clearance specifications: the model with 19-inch wheels has a minimum ground clearance of 196mm, while the model with 17-inch wheels has a minimum ground clearance of 188mm. Here is more information about ground clearance: 1. Definition: Minimum ground clearance refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when the vehicle is fully loaded and stationary. It is used to indicate the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. 2. Impact of minimum ground clearance on driving: The smaller the ground clearance, the worse the ability to pass over obstacles. Sedans typically travel on flat urban roads, hence they have smaller ground clearance. Off-road vehicles have larger minimum ground clearance to allow them to pass over larger obstacles.
16
1
Share

Launch Date of China 6 Emission Standard Fit in the Chinese Market?

2020 Fit China 6 was launched on November 29, 2019. Below are the specific details about the Fit: 1. Historical Background: The Fit is a hatchback introduced by GAC Honda. The third-generation Fit was launched on May 29, 2014, positioned as a "stylish and cool hatchback" targeting the new generation of "post-90s" who pursue individuality, with a spacious interior. 2. Configurations: Equipped with Honda's new EDT engine, a 1.5L direct-injection DOHC i-VTEC engine, CVT continuously variable transmission, Idle-stop engine energy-saving automatic start-stop system, VSA vehicle stability control system, three-mode rearview camera display system, ESS emergency braking warning system, HSA hill start assist system, intelligent screen connectivity system, and ten other advanced technologies leading its class.
4
2
Share

Is the Front Tire Pressure Higher or the Rear Tire Pressure?

Generally, the tire pressure of the front wheels of a car is higher than that of the rear wheels. Here is the relevant information: 1. Reason: Because the front of the car has the engine, the weight of the front part is greater, which results in the front tire pressure being slightly higher than the rear tire pressure. Therefore, the owner only needs to ensure that the tire pressure of the two front wheels and the two rear wheels is consistent, and it is not necessary for all four wheels to have the same tire pressure. 2. Tire pressure detection method: Use a wireless transmitter to send pressure information from inside the tire to the central receiver module, and then display the tire pressure data of each tire. When the tire pressure is too low or there is a leak, the system will automatically issue an alarm.
17
3
Share

Is the Alpina B7 a BMW 7 Series?

Alpina B7 is a modified version of the BMW 7 Series. The following are the specific details of the BMW 7 Series: 1. Development History: The BMW 7 Series is BMW's top-tier luxury sedan series, with a body style of a 4-door sedan and a front-engine, rear-wheel-drive layout. The BMW 7 Series is the flagship model of BMW and is only available in sedan form. It is manufactured by BMW and replaced the previous-generation model, BMW New Six, in 1977. 2. Body Dimensions: The dimensions of this series are 5212mm in length, 1902mm in width, 1478mm in height, with a wheelbase of 3210mm.
2
1
Share

When did the China III emission standard come into effect?

The China III emission standard was implemented on July 1, 2008. Here are detailed introductions about the China III standard: 1. Overview: The China III standard is the abbreviation for the National Phase III Emission Standard, equivalent to the Euro III emission standard. This means the tailpipe pollutant levels under China III are comparable to Euro III. However, China III mandates that new vehicles must be equipped with an OBD (On-Board Diagnostics) system. 2. China III Engines: China III engines improved upon China II engines by modifying internal structures, typically involving components such as cylinder heads, intake and exhaust manifolds, valves, camshafts, pistons, and corresponding auxiliary mechanisms. These modifications aim to reduce emissions without compromising power, requiring higher precision for each component, though external differences are not significant.
14
5
Share

What is Cold Gear Shifting?

Cold gear shifting is a training method used in driving schools to familiarize learners with vehicle gear positions. It involves practicing gear shifting (without starting the engine) on a manual transmission car parked in place, requiring standardized movements consistent with actual driving operations. Below are specific techniques for vehicle gear shifting: 1. Downshift after deceleration: Increase speed before upshifting and reduce speed by releasing the throttle before downshifting. Always fully depress the clutch pedal before shifting, and operate the gear lever with light, quick, gentle, and precise movements. 2. Master the timing of gear shifting: Shift gears when the engine reaches around 2000 RPM. The downshift sequence depends on vehicle speed - generally downshift when engine RPM drops below approximately 1500 RPM. 3. Maintain smooth shifting motions: Fully depress the clutch in one motion and engage gears decisively. Familiarize yourself thoroughly with gear positions. If unable to engage a gear, shift to neutral, release the clutch briefly, then depress it again to successfully engage the gear.
12
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.