What Are the Reasons for No Response When Turning the Vehicle Key?

1 Answers
LeGrace
07/25/25 2:39pm
There are many potential reasons why a car key fails to start the engine. It could be due to a dead battery, wiring issues, insufficient fuel, or problems with components in the fuel system, ignition system, or exhaust system. Below are more relevant details: 1. Car Gear Position: An incorrect gear position can also prevent the car from starting. Generally, the P (Park) or N (Neutral) gear is the correct position for starting an automatic transmission vehicle. If the driver accidentally leaves the gear in R (Reverse) or another position, it may not only fail to start but also pose a safety hazard. 2. Car Electrical Circuit: If the issue is related to the electrical circuit, the failure to start may occur suddenly. Common faults that cause no response when turning the key include blown fuses, open circuits in the high-voltage coil or low-voltage circuit, detached central ignition wire, leaking distributor rotor, or damaged spark plugs.
Was this review help?
6
0
Share
More Forum Discussions

Can You Drive with Only Three Lug Nuts on a Tire?

Tire with only three lug nuts cannot be driven. Lift the car: Prepare gloves, a new tire, and a jack. Place the jack under the frame on the side where the tire needs to be replaced. Operate the jack to lift the car. Remove the old tire: Use a wrench to sequentially remove the bolts of the tire that needs to be replaced, then take off the wheel. Install the new tire: Align the new tire with the axle and bolt holes, initially tighten the lug nuts. While tightening the nuts, you can step on the sidewall part at the bottom of the tire with your foot. Lower the car to complete installation: Lower the jack and tighten each bolt in a diagonal sequence. When replacing a tire, ensure you are in a safe and stable location to prevent the car from rolling.
3
5
Share

Is It Normal for a Battery to Heat Up While Charging?

It is not normal for a battery to heat up while charging. Precautions for battery charging: Avoid storing the battery in a depleted state: A depleted state refers to when the battery is not charged in time after use. In this state, sulfation is likely to occur, where lead sulfate crystals form on the plates, blocking ion channels and leading to insufficient charging and reduced battery capacity. The longer the battery remains idle in a depleted state, the more severe the damage. If the battery is not in use, it should be charged once a month to extend its lifespan. Regular inspection is necessary: During use, if the electric bicycle's range suddenly drops by several kilometers in a short period, it is highly likely that at least one battery in the pack has issues such as broken cells, softened plates, or shedding of active material from the plates, leading to a short circuit. Battery charging duration: The battery typically requires 8 to 12 hours to charge.
8
0
Share

How to Study for B2 Driver's License Points Deduction?

Drivers must report to the traffic management department of the public security authority at the place where the motor vehicle driver's license was issued or where the violation occurred within fifteen days to participate in a seven-day study session. Below is relevant information: 1. Handling Procedure: Motor vehicle drivers must report to the traffic management department of the public security authority at the place where the motor vehicle driver's license was issued or where the violation occurred within fifteen days to participate in a seven-day study session on road traffic safety laws, regulations, and related knowledge. After completing the study session, the vehicle management office must conduct a test on road traffic safety laws, regulations, and related knowledge within twenty days. 2. Annual Review Content: Review the handling of violation points deduction; review the driver's physical condition; review the test results of the safe driving course; only after all violation fines are paid, the physical examination is approved, and the test is passed, can the points for the scoring cycle be cleared.
13
3
Share

What is the most ideal reference for cylinder boring?

Cylinder boring is most ideally referenced to the lower plane. Purpose of cylinder boring: The purpose of cylinder boring is to eliminate surface shape errors on the cylinder to accommodate new pistons. Effects of cylinder surface wear: The degree of cylinder wear has the greatest impact on the power performance of a vehicle. Cylinder wear increases the clearance between the cylinder and the piston or piston rings, reducing the compression pressure in the cylinder and leading to a decline in engine performance. Along the cylinder axis, the wear forms a taper that is larger at the top and smaller at the bottom. The maximum wear occurs at the cylinder wall corresponding to the first piston ring when the piston is at top dead center. The upper part of the cylinder, which does not come into contact with the piston rings, shows almost no wear, forming a step. The wear around the circumference of the cylinder is also uneven, forming an irregular oval shape. The maximum radial wear area is usually near the opposite side of the intake valve.
13
1
Share

How Long Can a Car Battery Generally Be Left Unused?

Car batteries can generally be left unused for about one month. If the vehicle starts normally within a month, it indicates the battery is in good condition. Starting within 15 days is also considered normal. Beyond 30 days, the vehicle typically won't start, although the dashboard may still display information. After 60 days, there will usually be no display at all. A car battery, also known as a storage battery, is a type of battery that works by converting chemical energy into electrical energy. The commonly referred to car battery is a lead-acid battery, which is primarily made of lead and its oxides, with a sulfuric acid solution as the electrolyte. The normal service life of a car battery varies from 1 to 8 years, largely depending on the vehicle's condition. Under normal circumstances, with proper alternator charging and no electrical leakage or grounding issues, the battery can generally last more than 3 years.
6
0
Share

Which is more fuel-efficient, the new Jetta or the new Santana?

Jetta is more fuel-efficient, with a combined cycle fuel consumption of 5.7L/100km, while Santana has a combined cycle fuel consumption of 6.2L/100km. More details about the Jetta are as follows: 1. The 1.5L engine of the new Jetta has a maximum power of 81KW. The engine adopts advanced technologies such as Freilauf generator, dual VVT timing adjustment system, integrated intake/exhaust camshaft in the cylinder head cover, and continuously adjustable oil pump, effectively reducing fuel consumption while further improving emissions and noise. 2. The CO2 emissions of the Jetta are reduced to 64g/km, and the noise is reduced by 1.5dBA. The AQ160 automatic transmission paired with the 1.5L MPI engine also features an additional ECO-Mode, providing smoother gear shifts. The automatic transmission model achieves the same fuel consumption level as the manual transmission model, with a combined cycle fuel consumption of only 5.7L/100km.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.