What are the reasons for no air coming out of the BMW 3 Series air conditioning?

1 Answers
DeHarmony
07/30/25 1:22am
The reasons for no air coming out of the BMW 3 Series air conditioning are clogged air filter, damaged blower, or faulty air door. Below are the detailed explanations: Clogged air filter: The air filter is a significant and common reason for no air coming out of the air conditioning. During operation, the car air conditioning absorbs many impurities from the air, leading to a clogged air filter. If there is no air coming out, you can remove the air filter and check if it is clean. If the air filter is too dirty, it needs to be replaced promptly. You can go to a 4S shop or a repair shop for this. Blower failure: The car blower is a crucial component for air conditioning airflow. If the air conditioning compressor fails during use, the car air conditioning will definitely not blow air. Overheating damage to the internal coil of the blower or capacitor failure are major reasons for blower malfunction. You can turn the car air conditioning to the maximum and listen for the sound of the blower. If it is confirmed to be a blower failure, you need to visit a 4S shop for repair. Air door failure: The air door is located inside the air duct. Since it is made of plastic, it can get stuck or break. In such cases, the air drawn in by the blower cannot flow out from the air vents, resulting in no air coming out. You need to remove the air conditioning vents for inspection and then carry out repairs based on the situation.
Was this review help?
10
3
Share
More Forum Discussions

How to Use Mini Wiper?

The default "O" position is the off position for the vehicle wiper. The bottom "1x" position is the single wipe action position. Pushing the wiper stalk to the "I" position activates the low-speed wiper action. Pushing the wiper stalk to the "II" position activates the high-speed wiper action. The knob on the right controls the rear wiper function of the vehicle.
5
3
Share

How to resolve P0175 system too rich?

Check if low-quality fuel has been added; inspect for mechanical causes of compression leaks leading to fuel shortage. Check if there are faults in the ignition system; inspect the fuel system for malfunctions; examine the intake system for issues. Check the oxygen sensor and its wiring for faults.
19
2
Share

How to use the Q3 dash cam?

When the screen is lit and in recording mode, press the "MENU" button to turn the audio recording on/off. When the screen is lit, press the "OK" button once to stop recording, and vice versa. Press the "MODE" button to switch between the three functions: photo, playback, and recording. Press the "OK" button to confirm the currently selected function.
16
4
Share

How to engage the R gear when it's on the left side of first gear?

R gear indicates the vehicle is in reverse. To operate it, you typically need to press the safety button on the shift lever before moving the lever to the "R" position. Press the gear lever downward and then push it to the upper left to engage the R gear. Do not force the shift into R gear when the vehicle hasn't come to a complete stop, as this may damage the transmission.
12
4
Share

How to resolve the u015187 fault code?

u015187 fault code indicates a communication loss with the airbag system restraint control module. It is necessary to inspect the airbag connector wiring harness to check for proper contact. The fault code should be cleared strictly according to the method specified for the specific vehicle model. Simply removing the negative battery ground cable to clear the fault code is not recommended.
8
3
Share

How to Properly Start and Stop an Audi Q5L?

First, enter the vehicle and press the brake pedal with your foot—the brake is the one on the left. After pressing the start button, the car will start. If you need to move the car, press the brake again and shift the gear to D (Drive) mode. Once the gear is shifted to D mode, release the handbrake by pressing it downward once. Gradually release the brake pedal to start moving the car. To increase speed, press the accelerator pedal. To stop, press the brake pedal, then press the [P] (Park) button on the gear lever, and finally pull up the handbrake button to complete the parking process.
17
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.