What are the reasons for ineffective braking?

1 Answers
CaydenRose
07/24/25 9:23pm
Ineffective braking can be caused by: 1. Damage to the brake master cylinder; 2. Insufficient brake fluid; 3. Excessive wear of the brake pads. The maintenance methods for brakes include: 1. High-temperature protection to prevent corrosion of the braking system and avoid brake pad seizure due to high temperatures; 2. Cleaning oil stains from brake discs and drums to ensure proper heat dissipation; 3. Regularly replacing brake fluid; 4. Periodically checking the thickness of brake pads or shoes. The steps to replace a brake disc are: 1. Open the engine compartment and check the brake fluid level to prevent overflow during replacement; 2. Remove the wheel where the brake is located and the bolts of the brake caliper; 3. Take off the old brake disc; 4. Install the new brake disc, tighten the guide bolts, and complete the replacement.
Was this review help?
14
3
Share
More Forum Discussions

What are the disadvantages of automotive LED lights?

LED disadvantages are as follows: 1. Heat dissipation issues, poor heat dissipation can significantly shorten lifespan. 2. Energy efficiency of low-end LED lights is lower than energy-saving lamps (cold cathode fluorescent lamps, CCFL). 3. Higher initial purchase cost. 4. Due to the strong directionality of LED light sources, luminaire design needs to consider the special optical characteristics of LEDs. Advantages are as follows: 1. Energy saving and environmental protection: LED lights consume only 1/20 the energy of halogen lamps. 2. Low cost and long lifespan: LED lights from reputable manufacturers can last up to 100,000 hours. 3. High brightness: Much brighter than halogen lamps, making them ideal for brake lights and warning lights (strong penetration). 4. Low voltage safety: LEDs, originally used in electronics, only require 12V DC to operate, eliminating concerns about the 20,000+ volts of xenon lights. 5. Instant illumination: No more waiting for xenon lights to warm up - immediate on/off capability.
14
4
Share

How to Replace the Key Battery for MG?

Method to replace the key battery for MG: 1. Pop open the car key, and there is a gap in the middle that can be pried open directly by hand; 2. After opening the key cover, you will see the battery inside consists of two parts: the battery and a rubber ring. Remove the old battery, replace it with a new one, and then close the key cover to continue using it. Taking the MG5 as an example, its center console features a 12.3-inch combined virtual instrument panel, a 10.25-inch IPS high-definition color screen, a fighter-style electronic gear lever, the leading-in-class Zebra Venus system, and the MG Safety Fast full-time safety assistance system, all of which exude a strong trendy vibe. The full-time safety assistance includes a wealth of functions such as ACC adaptive cruise control, LDP lane departure warning, AEB automatic emergency braking, SAS speed assistance system, and more.
18
3
Share

Which country is Pirelli tires from?

Pirelli is a tire manufacturer from Italy. Pirelli has many products and also provides tires for many car brands. Here is some relevant information about tires: 1. Tires are a very important component of a car because they are the only part of the car that comes into contact with the ground, so tires are related to the driving safety and stability of the car. There are many tire brands, such as Pirelli, Michelin, Hankook, etc. Tire pressure is very important for tires. It is recommended to check the tire pressure frequently during daily use. 2. Tire pressure should not be too high or too low. If the tire pressure is too high, it will reduce the contact area between the tire and the ground, which will reduce the friction between the tire and the ground. If the tire pressure is too low, the tire may experience wave deformation during high-speed driving, which will reduce the service life of the tire and increase the risk of a blowout.
17
4
Share

What kind of paint is used for motorcycle shell spraying?

Motorcycle shell spraying should use special plastic paint for motorcycles. More information about special plastic paint for motorcycles is as follows: 1. Special plastic paint for motorcycles is a plastic paint made of high-performance resin, imported additives, weather-resistant color paste, and glitter powder. 2. Advantages of special plastic paint for motorcycles: strong adhesion, high hardness, and good decorative effect. 3. Uses of special plastic paint for motorcycles: used for painting motorcycle, electric bicycle, and electrical appliance shells. 4. Before using special plastic paint for motorcycles, stir the paint evenly, adjust the construction viscosity to about 11-13 seconds with matching thinner, the air compressor pressure during spraying should be around 2-3kg/m², the construction temperature is best within the range of 12-30℃, and the relative humidity of the construction site should not exceed 70%.
13
0
Share

What Causes Engine Noise in the Chevrolet Cruze?

Reasons for engine noise in the Chevrolet Cruze: 1. Loud engine noise due to carbon buildup in the engine. Regular cleaning of engine carbon deposits is necessary to ensure normal engine operation. 2. It is normal to hear the engine working sound outside the car, but if the engine noise becomes louder inside the car, this may be due to poor sound insulation. The vehicle's sealing strips should be checked for signs of aging. 3. Insufficient coolant can cause the engine noise to increase. The coolant level should be checked, and if the coolant temperature is too low, it can also lead to excessive engine noise. 4. During operation, the engine may experience knocking, which occurs when the remaining air-fuel mixture ignites spontaneously after the spark plug fires. In this state, the engine noise will also increase, and knocking sounds may occur.
6
1
Share

When Should the Throttle and Fuel Injectors Be Cleaned?

The throttle should be cleaned approximately every 20,000 kilometers, while the fuel injectors should be cleaned every 2 years or around 60,000 kilometers. If not cleaned regularly, fuel consumption may increase and power output may decrease, so it's best to maintain a regular cleaning schedule. However, cleaning the throttle too frequently is not advisable, as excessive cleaning can gradually wash away the special coating inside the throttle chamber, making it more prone to sludge buildup. There are two common failure modes for fuel injectors: 1. Using low-quality gasoline, which contains excessive impurities, can lead to clogged injectors, resulting in reduced vehicle power and sluggish acceleration. 2. Carbon buildup in the injectors, caused by prolonged incomplete fuel combustion due to habits like driving at high gears with low speeds or extended idling, accelerates engine carbon deposits. When injectors are clogged with carbon, fuel atomization becomes poor, leading to incomplete combustion and creating a vicious cycle that reduces engine power, increases fuel consumption, and causes excessive exhaust emissions.
14
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.