What are the reasons for frequent car stalling?

1 Answers
StJack
07/29/25 2:36pm
Car frequently stalls due to: system component malfunctions or fuel system issues. Any component failure in the three major systems - intake system, fuel system, or ignition system - can cause repeated stalling. Fuel system problems typically result from using substandard fuel, leading to fuel line blockages, fuel pump damage, or carburetor inlet clogging. Intake system failures may involve detached components like air filter boxes, intake pipes, crankcase ventilation valves, or crankcase air intake pipes, requiring part replacement; or throttle-related issues such as throttle valve clogging, carbon buildup, or abnormal throttle opening, necessitating throttle cleaning.
Was this review help?
1
3
Share
More Forum Discussions

What is the impact of the number of teeth on the front sprocket of a motorcycle on speed?

Motorcycle front sprocket with more teeth will reduce the speed, because the motorcycle has a fixed output power. With a fixed number of teeth on the front sprocket, the more teeth on the rear sprocket, the more powerful the start-up, but the lower the top speed; the fewer teeth on the rear sprocket, the weaker the start-up, but the higher the top speed. The number of teeth on the motorcycle's front and rear sprockets usually differs significantly. The front sprocket (drive sprocket) typically has 13-15 teeth, while the rear sprocket (driven sprocket) usually has 30-50 teeth. Off-road motorcycles often have even more teeth on the rear sprocket to increase output torque for better off-road capability. When modifying sprockets, increasing the number of teeth on the front sprocket or reducing the number of teeth on the rear sprocket can increase the speed at the same engine RPM, but the corresponding output torque will decrease, resulting in slower acceleration. Generally, with the front sprocket size unchanged, a larger rear sprocket will enhance the vehicle's power performance but reduce speed, while a smaller rear sprocket will increase speed but decrease climbing ability.
11
2
Share

How to Prevent Motorcycle Accidents?

Before riding, check the motorcycle's brakes and tire pressure, wear a helmet, and avoid riding too fast. When riding in urban areas, never exceed the speed limit, regardless of road conditions. Always consciously comply with traffic laws and regulations. Do not recklessly run red lights, ride against traffic, or speed. Avoid darting haphazardly on the road.
2
2
Share

How to Wheelie a Motorcycle in The Crew 2

After the vehicle starts moving, while slowly rolling, pull the clutch and increase throttle, then quickly release to utilize the strong torque of first or second gear to lift the front wheel. When the vehicle is moving at medium speed, downshift to second or third gear, then apply strong throttle to abruptly lift the front wheel.
17
1
Share

How to Get a Gecko Out of the Car?

Prepare a tall and wide-mouthed glass bottle, clean and dry it, then place a few pieces of crushed rock sugar inside. Cover most of the bottle opening to lure the gecko into climbing in for food. You can also use a 1:20 diluted bleach solution to wipe down the interior of the car. However, since the bleach will evaporate after some time, it's necessary to reapply periodically.
2
1
Share

How to Adjust a Loose Chain on a 125cc Motorcycle?

Lift the main stand, use an adjustable wrench to loosen the large nut counterclockwise, and use a 12# wrench to loosen the adjusting bolt lock nut, then adjust the adjusting bolt. Adjust until the tightness is appropriate, ensuring both sides have the same scale marks, then tighten the adjusting bolt lock nut, followed by the axle large nut. Apply lubricating oil, preferably using a dedicated chain oil if available.
13
1
Share

How to Fold a Folding Bike?

Stabilize the folding electric bike, locate the middle buckle on the handlebar, loosen it by flipping it open, then rotate the handlebar downward and re-buckle it. Locate the middle buckle on the handlebar post, flip it open to loosen, then fold down the handlebar. Flip both pedals inward. Loosen the buckle under the seat to adjust the seat position. Similarly, locate the middle buckle on the bike frame, flip it open to loosen, then fold the frame and re-buckle it. The folding electric bike is now fully folded.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.