What are the reasons for a new car's steering wheel being misaligned?

2 Answers
McTanner
07/24/25 7:51am
The reasons for a new car's steering wheel being misaligned are: 1. Objective factors causing the steering wheel to appear misaligned when it actually isn't, such as personal misperception or uneven road surfaces; 2. The steering wheel is slightly misaligned but not severely, which is a common phenomenon in many vehicles and generally considered normal as long as it doesn't affect normal driving; 3. Uneven tire pressure: It is recommended to first check if the tire pressure of all four tires is within the normal range and if there is a significant difference in pressure values. If the tire pressure is abnormal, adjust it to the normal range; 4. The problem indeed exists and is very severe, indicating a fault with the vehicle itself, and it is advisable to verify this at a 4S shop.
Was this review help?
10
0
Share
MaxAnn
08/11/25 3:33am
I often work in the garage and notice many new cars have misaligned steering wheels, primarily due to improper wheel alignment. This could be because the suspension system wasn't calibrated correctly during factory assembly, or the car got jolted out of alignment during transportation. Other causes include uneven tire pressure, loose steering column installation, or even early-stage wheel hub bearing wear. If the steering is off, you'll feel the car constantly pulling to one side while driving. Over time, this leads to uneven tire wear and wasted fuel. My advice is to take it directly to a professional shop for a comprehensive check-up. They can realign it properly with specialized equipment—don't attempt DIY fixes that might worsen the situation. Many new car owners overlook this seemingly minor issue, but it directly impacts driving safety. Addressing it promptly saves both money and hassle.
Was this review help?
16
2
Share
Expand All
More Forum Discussions

Is Beijing Auto Senova a Joint Venture Car?

Senova is a domestic product. Senova is a high-end brand under BAIC, officially launched at the 2012 Guangzhou Auto Show. The original Saab car brand, Saab and BAIC signed a contract in 2009 to acquire Saab's three major car platforms: 2400, 2900, and Epsilon platforms, as well as two engines (2.0T, 2.3T); two manual transmissions (F25, F35); and four main systems: development system, quality assurance system EM, supplier management organization, department, and manufacturing system. Through transformation and upgrading, Senova was established. Below is some extended information about "Senova": 1. Senova is a Swedish luxury car brand, as renowned as high-end sedans like Mercedes-Benz and BMW, with its outstanding performance earning the reputation of "King Before the Run." 2. Senova pioneered several automotive technology milestones, such as "first applying aircraft turbocharging technology to civilian vehicles," "rear-wheel steering system," and "reindeer antler safety body." Senova's relentless pursuit of technology and safety made it the Swedish Royal Car. 3. In 2009, Beijing Auto successfully acquired Saab's core intellectual property, changing the passive situation in China's pure technology market and opening a new path for technological development.
16
5
Share

How to Restore a Dash Cam to Factory Settings?

Methods to restore a dash cam to factory settings: Click the settings button on the dash cam, then select system settings, and choose the option to restore factory settings. After restoring the dash cam to factory settings, all recorded content will be erased, and the storage card will be formatted. Therefore, it is important to export any important files before formatting. A dash cam is an instrument used to record images and sounds during vehicle travel. Car owners with dash cams installed can submit the recorded footage and images as evidence to the police in case of accident disputes.
7
3
Share

Why Should the Left Reverse Parking Start Earlier Than the Right?

Why should the left reverse parking start earlier than the right? The explanation is as follows: The principles of left and right reverse parking are the same, but the distance and angle of the left and right rearview mirrors from the driver make the reference points different. The key point in reverse parking is when the distance between the car body and the parking spot corner is 30cm. For right reverse parking, this distance is about two fingers' width in the mirror, while for left reverse parking, this distance is slightly more than two fingers' width. Additional information: 1. Left reverse parking technique: Generally, you can start turning the steering wheel 10cm earlier than in right reverse parking, but this can be hard for beginners to master. Alternatively, you can start turning when the lower edge of the left rearview mirror aligns with the stop line, then observe the distance between the rear wheel and the parking spot corner in the mirror as it narrows. Once it reaches 30cm, turn the steering wheel back one full turn. If the distance is too narrow, you can adjust the steering wheel earlier to widen the distance and then fully turn the wheel once the desired width is achieved. 2. Other techniques: The principles of observing the parallelism between the car body and the parking lines and the timing to stop are the same. The only slight difference between left and right reverse parking is the initial turning of the steering wheel. Even if you don't start turning earlier in left reverse parking, you can still adjust the distance by fine-tuning the steering wheel. As long as the car body doesn't cross the lines, even if the car is parked slightly crooked, you won't lose points.
13
2
Share

What Causes a Car Window to Automatically Roll Down After Being Rolled Up?

When a car window rolls up and then automatically rolls back down, there are generally two reasons: 1. The result of the anti-pinch function activating—check if the window seal is too dirty or if resistance has increased. 2. A malfunction in the window motor—the position needs to be reset by rolling the window all the way up and holding the switch in the upward position for 10 seconds. One-touch window control: A system that allows car window glass to be raised or lowered to position with a single touch. Cars equipped with one-touch window control have a two-stage window switch. The first stage operates like a standard power window, while pressing and releasing the second stage will automatically fully open or close the window.
5
1
Share

How to Lower the Car Seat Headrest?

The method to lower the car seat headrest: The adjustment button is located next to the two support rods of the headrest or on the side of the headrest. Press the adjustment button to pull the headrest up or down. Some high-end models can automatically adjust the height, eliminating the need to manually pull the headrest. During long drives, the headrest can help reduce fatigue, but it is crucial not to change the headrest's height just because the correct position feels uncomfortable. If the correct headrest position is uncomfortable, consider adding a high-quality neck pillow, which can not only alleviate fatigue but also provide cushioning protection for the neck. The headrest should not be too high or too low, as this could affect driving safety.
12
4
Share

Should You Shift Gear First or Release the Handbrake First When Starting an Automatic Car?

Generally, you should shift gear first and then release the handbrake last. It is essential to press the brake pedal, and reversing the order is not a big issue. However, it is crucial to remember not to forget releasing the handbrake and avoid starting the car with the brake engaged, as this can burn out the handbrake linings. If you are a beginner and not yet accustomed to the process, you may release the handbrake first to avoid forgetting after starting. More details are as follows: 1. Shift gear first, then release the handbrake: Whether it's a manual or automatic transmission car, the most important step when starting is to shift gear first and then release the handbrake. The handbrake serves as the final safety measure, and it should only be released after the gear is fully engaged and before moving the car. This approach is very safe. When shifting gears, move quickly from P to D to avoid passing through R, which can cause backlash and harm the transmission. 2. The dangers of engaging the gear without releasing the handbrake: If the gear is engaged but the handbrake is not released, all the power output from the engine will be absorbed by the torque converter, causing its temperature to rise sharply. Prolonged exposure to this condition can burn out the torque converter. For dual-clutch transmissions, engaging the gear puts the clutch friction plates in a semi-engaged state. Prolonged semi-engagement can lead to burning out the friction plates, so it is necessary to start the car as soon as possible.
17
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.