What are the reasons for a car not starting after being parked for a while?

1 Answers
Almeida
07/28/25 5:30pm
There are two situations where a car does not start after being parked for a while. The specific circumstances and possible causes are as follows: 1. The car does not start immediately after being turned off. In this case, there is a higher possibility of an electrical circuit malfunction. It could also be due to a sensor causing the circuit to stop working due to a temperature rise. A thorough inspection of the electrical circuit is required before attempting any solutions. 2. The car does not start on the first attempt after being parked for a while and requires several attempts to start. This situation may be caused by a fuel system malfunction, throttle idle valve malfunction, or excessive carbon buildup in the cylinders or valves. It is necessary to visit a nearby repair shop to diagnose and eliminate the cause of the fault.
Was this review help?
8
4
Share
More Forum Discussions

What is the difference between 0W and 5W engine oil?

The only difference between these two types of engine oil is their minimum operating temperature. 5W can be used in environments as low as -30 degrees Celsius, while 0W can be used in environments as low as -35 degrees Celsius. Here are the relevant details: 1. The 'W' stands for winter-grade oil: The preceding number indicates the oil's low-temperature fluidity, represented by the lowest applicable environmental temperature. 0W oil can normally start an engine in environments as low as -35 degrees Celsius, while 5W oil can do so in environments as low as -30 degrees Celsius. 2. 0W is more fuel-efficient than 5W: Although both 0W and 5W can meet the oil requirements for most regions in China under natural environmental conditions, their performance differs at the same temperature. At the same temperature, the CCS (Cold Cranking Simulator) index of 0W is better than that of 5W, meaning that 0W has better fluidity than 5W at low temperatures. The direct result of this improved fluidity is smoother cold starts for the engine and reduced resistance during engine operation, leading to better fuel efficiency.
1
0
Share

Why does the car's AC cool while driving but heat up when parked?

When the car's AC cools while driving but heats up when parked, this issue is mainly caused by the following reasons: 1. Poor heat dissipation in the AC and engine cooling system: High temperatures when parked lead to poor AC performance, while driving improves heat dissipation and restores normal AC function. 2. Dirty radiator condenser: Prolonged use causes dirt buildup on the condenser surface. Car owners need to regularly clean the condenser to maintain optimal AC performance. 3. Faulty cooling fan: The fan fails to rotate when idling with AC on, requiring replacement of the electric fan. 4. Malfunctioning AC system: Issues such as Freon leakage or insufficient Freon levels during refill/replacement prevent the AC from achieving proper cooling effects during operation.
13
2
Share

Should the AC be turned on for car air conditioning cooling?

When the car is set to cold air mode, the AC button needs to be turned on, whereas it is not required when using the heating mode. This is because the AC button represents the air conditioning compressor, which is only used in the cold air mode. Below are the relevant details: 1. Composition of car air conditioning: The car air conditioning system includes not only the compressor but also components like the condenser, evaporator, and expansion valve. During the cooling process, the compressor is one of the crucial parts of the refrigeration system. Therefore, it is essential to turn on the AC button when using cold air; otherwise, the system will only operate the blower, delivering air at normal temperature. 2. Method for using cold air: When using cold air, turn on the air conditioning switch, set the fan to high speed, and adjust the temperature control knob to the cold air zone. After a while, once the interior temperature drops, you can lower the fan speed. 3. No need for AC in heating mode: During winter when using heating, the AC button does not need to be activated. It's worth noting that in winter, due to the low external temperature and higher interior temperature, the windows are prone to fogging. This fogging is often caused by the significant temperature difference between the inside and outside of the vehicle. In such cases, turning on the AC button can speed up defogging, but it will consume some of the car's fuel.
11
3
Share

What Causes Car Turn Signals Not to Work?

Possible causes for non-functioning turn signals include a burnt-out turn signal relay or a blown turn signal fuse, which are two major factors. While the turn signal relay can be replaced by oneself, fuse replacement should be handled by professionals to avoid causing more severe vehicle malfunctions. Below are relevant details: 1. Definition of Turn Signals: Turn signals are crucial indicator lights activated when a motor vehicle changes direction to alert surrounding vehicles and pedestrians. These lights use xenon tubes with microcontroller-controlled circuits for alternating left/right flashing. They employ flasher units to achieve blinking, mainly categorized into thermal (bimetallic), capacitor, and electronic types. 2. Function of Turn Signals: As the primary device displaying a vehicle's dynamic information, turn signals mounted on both ends of the vehicle body ensure driving safety during turns. Proper usage allows others to anticipate vehicle movements and make correct decisions. 3. Usage Guidelines: (1) When entering or exiting roundabouts, activate corresponding turn signals based on travel direction. (2) During lane changes due to traffic congestion, check adjacent lane availability via mirrors without obstructing other vehicles, then activate appropriate signals before changing lanes. (3) When making U-turns, engage left turn signals while checking for approaching vehicles before executing the maneuver.
3
2
Share

What procedures are required for a C1 driver's license renewal?

Motor vehicle drivers shall apply for license renewal at the vehicle management office of the issuing authority with the required materials. The vehicle management office will process the renewal within one working day after approval. Renewal materials: Bring two copies of ID card, two 1-inch bareheaded color photos, original ID card, original driver's license, and a medical examination certificate from a county-level or above hospital (free physical examination is also available at the vehicle management office). Renewal and inspection must meet the following conditions: Holders of large passenger vehicle, tractor, city bus, medium passenger vehicle, or large truck driver's licenses have no demerit points in the current scoring cycle, or holders of other permitted vehicle-type driver's licenses have less than 12 demerit points in the current scoring cycle; Holders of large passenger vehicle, tractor, city bus, medium passenger vehicle, or large truck driver's licenses have demerit points in the current scoring cycle, and holders of other permitted vehicle-type driver's licenses who have caused a traffic accident resulting in death and bear equal or greater responsibility without having their motor vehicle driver's license revoked, have participated in the inspection education; The applicant has no pending road traffic safety violations or traffic accidents; The applicant's physical condition meets the driving license requirements; The motor vehicle driver's license is not under circumstances of being seized, detained, temporarily suspended, revoked, canceled, or annulled by law.
9
4
Share

What are the symptoms of a clogged car air conditioning expansion valve?

When the car air conditioning expansion valve is clogged, it increases the load required for the air conditioning compressor to operate, resulting in the air conditioning producing cool air but no airflow. The expansion valve is a crucial component of the car's cooling system, typically installed between the liquid reservoir and the evaporator. Here is the relevant information: 1. Definition of the expansion valve: The expansion valve allows medium-temperature, high-pressure liquid refrigerant to throttle into low-temperature, low-pressure wet vapor to achieve cooling effects. It controls the valve flow based on temperature changes at the evaporator's end, preventing insufficient utilization of the evaporator's surface area and knocking phenomena. 2. Function of the expansion valve: One is the throttling effect, and the other is controlling the flow of refrigerant. 3. Classification of the expansion valve: Thermal expansion valves can be divided into internal equalization and external equalization types based on the balancing method. In a car's refrigeration system, the expansion valve is one of the four major components, with the other three being the compressor, condenser, and evaporator.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.