What are the quick repair methods for vehicle paint scratches?

2 Answers
DiKinsley
07/29/25 5:05am
Quick repair methods for vehicle paint scratches: 1. Toothpaste repair: Toothpaste can only temporarily cover the scratches and will fall off over time without fixing the scratches; 2. Nail polish repair: Nail polish repair is a relatively low-cost method, but it should be noted that some nail polishes are corrosive and can easily damage the paint. Additionally, nail polish repairs do not last long and can cause color differences; 3. Touch-up pen repair: Using a touch-up pen to repair paint scratches is a common method with long-lasting effects and noticeable results; 4. Specialized paint scratch repair agent: Although more expensive, it provides obvious results and the repair is unlikely to fall off.
Was this review help?
11
2
Share
GabrielRose
08/12/25 6:25pm
I've recently dealt with quite a few paint scratches myself, and I find the simplest and quickest method is to first thoroughly clean the scratched area to ensure there's no dirt. Then, for shallow scratches, gently rub with a soft polishing sponge or professional repair paste, wait a few minutes before wiping it clean, and then apply a layer of car wax for protection. I have a few touch-up pens on hand, and the color needs to match, so handling small scratches basically takes about ten minutes and doesn't cost much. I also recommend regularly checking the car paint and avoiding parking in the sun for too long, as this can reduce oxidation and discoloration. If the scratch is too deep and reaches the primer, you'll need to use a spray paint kit, apply several layers, and then polish to prevent rust from spreading. The whole process is quite hassle-free and helps keep the car looking neat.
Was this review help?
1
5
Share
Expand All
More Forum Discussions

When driving, should you shift gears first or pull the handbrake first?

When driving, you should shift gears first. The specific reasons are as follows: 1. In a car's transmission, both the P (Park) and N (Neutral) gears disconnect the power transfer between the input and output shafts. However, the difference is that the P gear has an additional pawl gear mechanism at the end of the output shaft. 2. The pawl is fixed to the transmission housing, while the gear is fixed to the end of the output shaft. When the transmission is shifted into P gear, the pawl is pressed down to engage with the gear, achieving a locking effect. At this point, both wheels cannot rotate in the same direction simultaneously, preventing the vehicle from moving forward or backward. 3. The principle of the handbrake stopping the vehicle is by clamping the rear brake discs, preventing the rear wheels from rotating. Mechanical cable-type handbrakes use a steel cable to pull the brake caliper, which then clamps the brake disc, while electronic handbrakes operate a servo motor on the brake caliper to clamp the brake disc.
17
4
Share

What types of vehicles can be driven with an A1 driver's license?

A1 license allows driving large passenger vehicles (passenger vehicles with a length exceeding 6 meters or designed to carry more than 19 passengers). Requirements for upgrading to an A1 license: Must have held a B1 or B2 license for at least five years, with no record of full penalty points in the last three consecutive scoring cycles prior to application; or must have held an A2 license for at least two years, with no record of full penalty points in the last scoring cycle prior to application. Other vehicle types that can be driven with an A1 license include: A3 (city buses), B1 (medium-sized passenger vehicles), B2 (large trucks), C1 (small cars), C2 (small automatic transmission cars), C3 (low-speed trucks), C4 (three-wheeled vehicles), M (wheeled self-propelled machinery). Only an A2 license permits driving full trailers and semi-trailers, which an A1 license does not cover.
9
5
Share

Should You Press the Clutch When Making a U-Turn in Subject 3?

You do not need to press the clutch when making a U-turn in Subject 3. Specific steps for making a U-turn in Subject 3: Upon hearing the voice prompt "Please make a U-turn ahead," observe the road conditions. If there is sufficient distance from the vehicle ahead or no vehicle in front, press the brake to slow down. When the speed drops below 10 km/h, shift to 1st gear, turn on the left turn signal, glance at the left rearview mirror to confirm rear traffic safety, and after 3 seconds, perform the lane change operation, gradually moving into the U-turn lane. Situations where U-turns are not allowed in Subject 3: Do not make a U-turn on a pedestrian crossing, nor stop and wait on it. You must pass the pedestrian crossing before making a U-turn. If making a U-turn at a traffic light intersection where the center line near your side is solid, wait for the green light and cross the stop line to make the U-turn.
17
2
Share

What is the normal RPM for a car engine when it is just started?

When starting the car, the engine RPM of 1200 to 1500 is normal. More knowledge about car starting is as follows: 1. After the car starts, there is a high idle speed process, especially in winter, which is more obvious. This is a phenomenon controlled by the on-board computer (for vehicles with electronic throttle control systems). When the engine reaches a certain temperature, the idle speed will return to normal. This helps accelerate the engine temperature to the normal working condition when starting a cold car. 2. There may be slight abnormal noises when starting the car engine. If the noises disappear after a few minutes of warming up, this does not affect the vehicle's driving. Because after the vehicle has been parked overnight, the engine oil in various components has flowed back to the oil pan, so it is best to warm up the car for a few minutes in the morning. One reason is to allow the oil to be evenly supplied to all components, and the other is to raise the engine temperature for better performance.
17
2
Share

How Many Cylinders Does a 1.5t Engine Have?

1.5t engines come in both 3-cylinder and 4-cylinder configurations. Below are the differences between 3-cylinder and 4-cylinder cars: Difference in Stability: Four-cylinder cars clearly offer much better stability compared to three-cylinder cars. This is because the four-cylinder engine operates with each cylinder working separately, allowing the forces and counterforces to cancel each other out, significantly reducing engine vibration. Three-cylinder engines lack one cylinder, meaning there is a moment during operation when no cylinder is firing, resulting in noticeably more vibration. Consequently, the stability of three-cylinder engines is naturally inferior to that of four-cylinder, six-cylinder, and eight-cylinder engines. Difference in Structure: Three-cylinder engines have a simpler structure, are more compact, lighter in weight, and easier to arrange in a vehicle. Four-cylinder engines have a relatively more complex structure with one additional cylinder. In terms of structural design, three-cylinder engines have one fewer cylinder than four-cylinder engines, and correspondingly fewer camshaft attachments.
1
3
Share

What happens if spark plugs are never replaced?

Effects of not replacing spark plugs: If spark plugs are damaged, it can directly cause issues such as leakage in the vehicle's ignition system, increased fuel consumption, reduced power, and most importantly, difficulty in ignition, affecting the normal operation of the vehicle. Severe erosion of spark plugs, including blistering, damage, or melting of the electrodes, indicates that the spark plugs are ruined and should be replaced. Methods to determine if spark plugs are damaged: Remove the spark plugs and observe their appearance to assess their condition. Normal spark plugs have insulator skirts and electrodes that appear gray-white, gray-yellow, or light brown. A properly functioning spark plug has a reddish-brown insulator skirt, an electrode gap between 0.8-0.9mm, and no signs of electrode burn. If the spark plugs are covered in oil or deposits but are not damaged, they can continue to be used after cleaning off the oil and deposits. If the spark plugs are severely damaged, showing signs such as blistering, black streaks, cracks, or melted electrodes, the cause of the damage should be identified. After troubleshooting, replace the spark plugs with new ones. Additionally, if the spark plugs appear black as if smoked, it indicates the wrong heat range was chosen or the mixture is too rich, with oil seeping up.
2
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.