What are the procedures and precautions for new car inspection at the testing site?
3 Answers
The procedures and precautions for new car inspection at the testing site are as follows: 1. First, visually inspect the body paint surface to check for scratches, spots, dents, and wear. Observe the paint under sufficient sunlight to see if there is any color difference. Open the doors and adjust them to different angles to allow light to shine from various directions, checking if the sheet metal is smooth and if there are any signs of repair. 2. Check the vehicle identification plate, which is located on the side of the driver's door or in the engine compartment. Pay attention to whether the manufacturing date is too far in the past. If it exceeds six months, the car is likely a stock vehicle or a test drive car. Also, ensure that the information on the identification plate matches that on the vehicle certification. 3. Inspect the windshield. The numbers represent the most recent production year, and the dots indicate the production month. If the dots are on the left side of the number, it means the windshield was produced in the first half of the year. Subtract the number of black dots from 7 to get the specific year. If the dots are on the right side, it means the windshield was produced in the second half of the year. Subtract the number of black dots from 13 to get the specific year. If the windshield's production date is far from the car's production date—by a year or more—it is likely that the windshield has been replaced. 4. Open the engine hood and check if the engine compartment is clean. If the car has been stored for a long time or used, some areas may have noticeable dust or stains. Also, check if the engine oil level is sufficient and if other fluid levels are within the acceptable range. 5. Open the doors and check if they open and close smoothly and flexibly, with no noise from the hinges. Ensure the gaps between the doors and the front and rear bumpers are consistent and that the doors can be closed in one motion. 6. Check the production date of the tires. Since tires are purchased separately, their production date will naturally differ from the car's production date, which is not a major concern. However, if the tire production date is significantly older than the car's delivery date, it is worth noting. 7. Test the basic functions of the car, such as whether the windows roll up and down properly, the air conditioning cools, the air vents emit any unusual odors, the dashboard functions operate normally, the windshield wipers work, the lights turn on correctly, and the sunroof opens and closes smoothly. 8. Test drive the car if allowed. Observe whether the engine idles smoothly, the steering wheel vibrates noticeably, the front and rear seats shake significantly, or if there is any unusual noise inside the car.
I was both excited and a little nervous when I took my first brand-new car to the inspection station. The general procedure is to make an appointment online or by phone for a specific time to avoid peak-hour queues. Upon arrival, first go to the reception desk to submit documents: original ID card, copy of the car purchase invoice, original compulsory traffic insurance policy, and the vehicle qualification certificate. Then the car is guided to the inspection line, where staff will check if the lights are functioning properly (such as high beams, low beams, turn signals, and brake lights), and test whether the braking performance and exhaust emissions meet the standards. The whole process takes about one to two hours if everything goes smoothly. If it fails, you’ll receive a feedback report and need to go to a 4S shop for repairs. Important notes: before the inspection, ensure the vehicle has no modifications, especially no unauthorized decorations on the lighting system; check the tire pressure and engine oil for a new car, and make sure there are no fault codes in the engine for the exhaust test; bring some water and snacks to cope with the waiting time, and prepare all documents to avoid a wasted trip. It’s also fun to take photos or videos of the inspection process to share with friends. Don’t forget to pay the small inspection fee in cash or by scanning a QR code. After completion, collect the qualification certificate before getting the license plate. That time I went in the morning when it was less crowded and everything went smoothly—it felt very practical.
As an experienced driver familiar with the process, here's the new car inspection routine: First, submit required documents (ID, purchase invoice, insurance policy) at the inspection station check-in counter. Then the vehicle enters the testing area for key checks: exterior lights verification, brake system response test, chassis dynamic inspection for steering flexibility, and emission analysis. Contact dealers promptly if issues arise. Practical tips: Perform basic maintenance (e.g., full fuel tank) a week prior; avoid modifying factory configurations; bring document copies to save time; prepare ~50 yuan for quick payment; choose weekday mornings before 9am for shorter queues; wear comfortable shoes. New cars rarely fail, but thorough preparation prevents hassles. Post-inspection certification enables worry-free driving – an efficient process worth sharing.
