What are the prerequisites for taking the Subject 1 test?

1 Answers
LaChristian
07/30/25 10:35am
The prerequisites for taking the Subject 1 test are as follows: 1. Vision: For applicants applying for large passenger vehicles, tractors, city buses, medium-sized passenger vehicles, large trucks, trolleybuses, or tram driving licenses, the naked or corrected visual acuity of both eyes must reach 5.0 or above on the logarithmic visual acuity chart. For other driving license types, the naked or corrected visual acuity of both eyes must reach 4.9 or above on the logarithmic visual acuity chart. 2. Other aspects: No red-green color blindness. The actual driving school physical examination content should match the vision requirements. The ability to distinguish the direction of sound sources with each ear 50 centimeters away from a tuning fork. Both thumbs must be intact, and each hand must have at least three other fingers intact, with normal limb and finger movement functions. Normal motor function.
Was this review help?
15
1
Share
More Forum Discussions

Where is the engine oil filler port located?

The engine oil filler port is generally located on the left side of the engine. 1. Slowly unscrew the oil filler cap in the reverse direction, open the cap, and pour in the oil. When reinstalling the oil filler cap, use the oil on the dipstick to lubricate the cap opening, then smoothly tighten it in the correct direction until it is properly seated. 2. Regarding the position for adding engine oil, the oil should be filled up to the upper limit mark on the dipstick for optimal performance. Overfilling can create excessive resistance for the engine, which may increase fuel consumption. Below are the basic steps for adding engine oil: (1) After the car has been turned off and parked for about ten minutes, pull out the dipstick and wipe the oil marks clean with a cloth. (2) Reinsert the dipstick into the dipstick tube, then pull it out again to check the oil marks. Normally, the oil marks should be between the upper and lower marks on the dipstick, slightly above the middle line. (3) If the oil marks are below the lower mark, it indicates insufficient oil, and you should add oil immediately. While adding oil, continuously pull out the dipstick to monitor the oil level. (4) When topping up the oil, try to use the same type of oil as the one already in the engine to avoid mixing different brands or grades of oil.
18
0
Share

How to Turn Off Auto Start-Stop in a Car?

The steps to turn off the auto start-stop feature in a car are as follows: 1. Press and hold the brake pedal while the vehicle is in normal operation. 2. The auto start-stop system will activate, and the indicator light on the dashboard will illuminate. 3. Press the "off" button for the auto start-stop system. 4. The dashboard will display that the system has been turned off, indicating the auto start-stop is deactivated. Here is an introduction to the auto start-stop feature: The engine auto start-stop system automatically shuts off the engine when the vehicle comes to a temporary stop (such as at a red light) and restarts it automatically when it's time to move forward again.
2
2
Share

How to Use the Heating System in the 10th Generation Accord

Before using the heating system in the 10th Generation Accord, you need to wait until the engine coolant temperature rises to a certain level. The heating control knob has red and blue color markers on both sides. Generally, the cold air setting is on the left, and the warm air setting is on the right. Turning the knob to the left decreases the car's temperature, while turning it to the right increases the temperature. After the engine coolant temperature has risen, you can turn on the air conditioning by adjusting the fan speed control. Below is an introduction to using the heating system in the Accord: 1. During winter use, after starting the engine, the coolant temperature is still relatively low. In this state, you should not use the heating system because the air blown by the AC will be cold. Turning on the AC immediately will not raise the interior temperature but will instead increase the engine's load. 2. When starting the car cold, you need to drive for a while until the engine coolant temperature rises and stabilizes at around 90 degrees Celsius. At this point, you can turn on the car's heating system. Set the air circulation to external circulation first to expel the cold air from the cabin, then switch to internal circulation. The interior temperature will rise quickly.
20
4
Share

What are the reasons for an automatic transmission not engaging?

The main reasons why an automatic transmission car cannot engage gears are the following two aspects: 1. A malfunction has occurred inside the gear lever assembly. 2. The P-gear locking solenoid inside the gear lever has failed, and the brake switch has malfunctioned. Here are the measures that can be taken if an automatic transmission car cannot engage gears: (1) Replace the vehicle's clutch cable. (2) Go to a professional auto repair shop and have professionals adjust the clutch cable and gear lock inside the vehicle, as these two areas being too tight can directly affect the difficulty of gear engagement, and in more severe cases, can even prevent the vehicle from engaging gears. (3) Replace the clutch master cylinder inside the vehicle to resolve the issue of not being able to engage gears.
17
3
Share

What are the differences between the BMW 318li and 320li?

The BMW 318li and 320li are both models from the same series. Below are some of their differences: 1. The 320i features integrated high and low beam xenon headlights, which the 318i lacks. Additionally, the 318i does not come with advanced automatic air conditioning, a windshield with a grey sunshade band, or a BMW professional-grade radio, unlike the 320i. 2. The 318i lacks a headlight cleaning system and automatic headlights, and it comes standard with halogen headlights. In contrast, the 320i is equipped with a headlight cleaning system and automatic headlights. 3. The 318i has a single-sided, flat oval exhaust pipe, while the 320i features a single-sided dual circular exhaust pipe. The 318i does not have a shark fin antenna, whereas the 320i comes with one.
14
5
Share

What is the general lifespan of tires?

Automobile tire lifespan is primarily determined by factors such as time, mileage, and driving habits: 1. Time: Generally 3-5 years 2. Mileage: 60,000-80,000 kilometers. 3. These time and mileage figures represent the typical tire lifespan for most drivers under normal driving conditions. However, actual tire longevity may vary depending on individual driving habits, road conditions, and parking environments. Below are methods to extend tire lifespan: (1) Avoid turning the steering wheel while stationary, steer clear of rough roads, maintain proper tire pressure, and perform professional wheel alignment. (2) Maintain good driving habits to protect against excessive tire wear and prolong service life.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.