What are the precautions for tire usage?

3 Answers
CarolineDella
07/29/25 8:11am
Precautions for tire usage: 1. Regularly check the tire surface for cracks, deformations, or other defects; 2. Park on level ground, avoiding surfaces with large, sharp, or pointed stones; 3. Do not splash water for cooling. Tires can overheat and experience increased pressure during prolonged or high-speed driving in summer. In such cases, park to allow cooling, but never release air to reduce pressure or splash water to cool, as this can cause abnormal aging of the tire rubber; 4. Avoid sudden braking. Maintain appropriate speed, be aware of road conditions, pedestrians, and other vehicles, prepare for braking, minimize frequent braking, and avoid emergency stops; 5. Choose good road surfaces. When driving through road construction or repair zones, proceed slowly at low speed and carefully select the path to take.
Was this review help?
17
2
Share
StBrooklyn
08/13/25 4:15am
As a veteran driver with over a decade of experience, tire maintenance is my daily priority. I make it a habit to check tire pressure every weekend morning when the car is cold for the most accurate reading. Low tire pressure increases rolling resistance, raising fuel consumption by 10% and potentially causing sidewall overheating and blowouts; excessive pressure leads to rapid center wear and reduced comfort. I use the onboard tire gauge to ensure values match the vehicle manual standards. Wear inspection is equally crucial—I measure tread depth with a coin, replacing tires if below 1.6mm to prevent hydroplaning. Rotating tires every 5,000 kilometers ensures even wear and extended lifespan. I avoid hard braking and sharp turns to minimize temperature spikes. In winter, I switch to snow tires for superior ice traction. These practices keep my repair visits minimal while ensuring safer, worry-free driving.
Was this review help?
12
0
Share
Expand All
DaisyRose
10/05/25 4:55am
During safe driving training, I always emphasize that tires are the cornerstone of road safety. Maintaining correct tire pressure is crucial to avoid the risks of overinflation or underinflation leading to loss of control. I recommend car owners check tire pressure monthly, as low pressure on wet roads increases the risk of skidding. Inspect tread depth using a specialized caliper or a simple coin test; replace tires if tread is below 4mm to prevent poor drainage and accidents. Watch for bulges or cuts and address them immediately. Drive smoothly, minimize high-speed sharp turns to prevent overloading and blowouts. Seasonal tire rotation extends overall lifespan and enhances reliability. These habits effectively prevent accidents and ensure the safety of both drivers and vehicles.
Was this review help?
20
5
Share
Expand All
More Forum Discussions

What does PEU mean in new energy vehicles?

PEU is the Power Electronic Unit in new energy vehicles, one of the most important components that distinguishes them from traditional fuel-powered vehicles. Relevant information is as follows: 1. Introduction: Currently, most motor drive systems integrate functions such as MCU (Motor Control Unit), DC-DC, OBC (On-Board Charger), and PTC (On-Board Heater). This power integration unit is called PEU. 2. Testing: Through PEU aging tests, the performance of the PEU in electric vehicles under various working conditions can be comprehensively evaluated. Besides PEU, new energy vehicles are often also equipped with VCU and BMS. 3. VCU: The Vehicle Control Unit in new energy vehicles is the core electronic control unit that implements vehicle control decisions. It is generally only equipped in new energy vehicles, as traditional fuel-powered vehicles do not require this device.
20
5
Share

What is an Oil Dipstick?

A graduated stick installed in the oil tank or oil pan, used to check the amount/oil level of lubricating oil in the engine. Here is relevant information: 1. Purpose: The function of the oil dipstick is not only to check the level of engine lubricating oil; experienced drivers or repair personnel can detect many engine operating dynamics by inspecting the oil dipstick, thereby maintaining the engine, promptly identifying the causes of faults or accidents, and preventing further deterioration of faults. 2. Meaning of Dipstick Marks: A standard oil dipstick will have clear upper and lower limit marks. It is sufficient to ensure that the measured oil level is between these two marks, with the middle position being ideal. It's important to note that more oil is not necessarily better. The higher the oil level, the greater the engine resistance. Ideally, the oil level should be kept slightly below the middle position, where the engine resistance is minimized, fuel consumption is lowest, and lubrication performance remains stable.
18
0
Share

What is SAE 0W-20 engine oil?

SAE 0W-20 is Toyota Genuine engine oil. Here is some extended information about engine oil: 1. Increased fuel consumption: When adding engine oil, the oil level should be between the upper and lower marks on the dipstick. If too much oil is added to the engine, the oil volume will expand when the engine temperature rises, causing increased pressure in the oil chamber and greater operating resistance. This will result in reduced vehicle power and increased fuel consumption. 2. Overfilling engine oil: If too much oil is added, the crankcase breather pipe may leak oil due to increased crankcase pressure. The oil seal may become loose under oil pressure, leading to oil leakage. 3. Heat dissipation: Excessive engine oil can affect engine cooling.
12
0
Share

How to Set the Time on Peugeot 308?

Peugeot 308 time setting method: 1. Start the car power or ignite the vehicle; 2. Press the Menu button to enter the main menu; 3. Use the directional keys below to select the personalized configuration menu item in the main menu, press the OK key on the keyboard to enter the personalized configuration display control interface; 4. Press the OK key on the keyboard to enter the personalized configuration display control interface; 5. Select to enter the date and time menu under the display settings menu, and set the year, month, day, hour, minute, and 12-hour or 24-hour format respectively; 6. After the setting is completed, press the OK key to save the set time and date data. The Peugeot 308 is a compact car, and the first Peugeot 308 model will be equipped with a 120-horsepower 1.6L inline 4-cylinder gasoline engine transplanted from the 207 model, inheriting the existing features of the Peugeot family models, such as the large-mouth air intake grille, raised engine cover, and the huge and eye-catching lion logo.
20
1
Share

How to replace the headlight of Haval H6?

Haval H6 headlight replacement method: 1. Unplug the power socket of the bulb. When unplugging the bulb power socket, apply moderate force to avoid loosening the socket wiring or damaging the bulb power plug; 2. After disconnecting the power interface, remove the waterproof cover behind the bulb. The waterproof cover of the headlight is mostly made of soft rubber, and some models are equipped with a soft plastic waterproof cover. Gently pull the waterproof cover off; 3. Remove the bulb from the reflector. When removing the bulb, use your fingers to pinch the wire clips on both sides, and then pull the bulb out after it is loosened; 4. Place the new bulb into the reflector and align it with the fixed position of the bulb. There are several fixed positions on the bulb base. Install it by reversing the steps of removing the old bulb; 5. When covering the waterproof cover, ensure that the edge of the waterproof cover is completely aligned with the fixed position. Finally, connect the headlight power socket.
1
1
Share

Can a car be exposed to rain immediately after painting?

It is not advisable to expose a car to rain immediately after painting. The duration before the paint can withstand rain depends largely on the painting process and the type of paint used. Generally, conventional car paint requires about a week before the car can be washed or exposed to rain. However, with rapid repair technology, the paint can be washed or even polished just one hour after leaving the workshop. Once the paint is completely dry, it forms a hardened protective film on the surface. If the car is exposed to rain before the paint is fully dry, it can compromise the protective effect, potentially leading to cracking in the future. Additionally, exposing the paint to rain before it is fully dry can also affect its glossiness. Car painting involves applying a layer of paint to the car's surface to protect it, typically using baking paint. The car painting process includes steps like applying putty, sanding, dust removal, cleaning, masking, and painting. Materials used in car painting include standard paint, metallic paint, pearl paint, clear coat, and matte paint.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.