What are the precautions during vehicle inspection?

1 Answers
DiCaroline
07/29/25 11:16am
When picking up and inspecting a car at a 4S dealership, pay attention to both vehicle inspection and document verification. Below are the relevant details about vehicle inspection during pickup: 1. Engine check: After cold-starting the engine, let it warm up for about 2 minutes. The engine sound should be smooth without any strange noises. Take a short test drive to ensure smooth gear shifting, no unusual body noises, and normal operation of electronic devices like air conditioning and audio. 2. Body inspection: The paintwork of a new car is applied by automated computer systems and should be flawless. If there is uneven protection or color differences in the paint, insist that the 4S dealership replace the vehicle. The interior should have no defects. After turning on the power, check all functions such as navigation, wipers, headlights, etc., to ensure they work properly. Test all buttons for smooth operation and verify that headlights can be turned on normally.
Was this review help?
7
2
Share
More Forum Discussions

What is the maximum speed limit for motor vehicles when descending a steep slope?

Motor vehicles must not exceed 30km/h when descending a steep slope. According to the "Highway Speed Limit Standards" and Article 42 of the "Road Traffic Safety Law", it is clearly stipulated that motor vehicles driving on the road must not exceed the maximum speed indicated by speed limit signs. The maximum speed limit for specific road sections should be determined according to the following standards: On highways without a center line, the speed limit is 40 kilometers per hour; On highways with only one motor vehicle lane in the same direction, the speed limit is 70 kilometers per hour; When entering or exiting non-motorized lanes, passing railway crossings, sharp curves, narrow roads, narrow bridges, or making U-turns, turns, or descending steep slopes, the speed limit is 30 kilometers per hour; The maximum speed limit on expressways is 120 kilometers per hour.
2
1
Share

How to Use the Turn Signals on a Toyota Corolla?

Toyota Corolla's turn signal switch is the lever on the left side of the steering wheel. Pushing it upward activates the right turn signal, pushing it downward activates the left turn signal, and returning it to the middle position turns it off. Below is the classification of car lights: 1. Headlights: Located at the front of the car, they primarily serve for illumination and signaling. The light emitted by headlights illuminates the road ahead, enabling safe driving at night. 2. Combination tail lights: Located at the rear of the car, they mainly serve for illumination and signaling. 3. Turn signals: Used to indicate left or right turns to other road users, required by regulations to be amber in color. 4. License plate light: Primarily illuminates the license plate, making it visible for identification at night.
8
5
Share

P0300-00 Engine Misfire Detected Causes?

P0300-00 Engine Misfire Detected Causes_58 Auto The P0300 trouble code indicates that the engine has detected multi-cylinder misfire. The fault systems that cause this phenomenon include the fuel injection system and ignition system, which are basically electrical circuit and electronic control faults. Here are the relevant explanations: ECU: The Powertrain Control Module (ECU) can detect "misfire" by monitoring the 3X reference voltage of the Ignition Control (IC) module and the camshaft position input signal from the camshaft position sensor. Fuel Injection System: The fuel injection system refers to a fuel supply device that injects a certain amount of fuel directly into the cylinder or intake manifold under certain pressure using an injector. Depending on the type of fuel injected, it can be classified into gasoline injection systems, diesel injection systems, gas fuel injection systems, etc.
19
0
Share

What tires are equipped on the 2018 Sagitar?

The 2018 Sagitar comes with 205/55-R16 tires, and the spare tire size is 195/65-R15. Tires are circular elastic rubber products assembled on various vehicles or machinery to roll on the ground. Usually mounted on metal rims, they support the vehicle body, cushion external impacts, achieve contact with the road surface, and ensure the vehicle's driving performance. Here is an introduction to tires: 1. They support the entire weight of the vehicle, bear the car's load, and transmit forces and moments in other directions. 2. They transmit traction and braking torque, ensuring good adhesion between the wheels and the road surface to improve the vehicle's power, braking, and passability; together with the car suspension, they mitigate the impact during driving and dampen the resulting vibrations. 3. They prevent severe vibrations and early damage to vehicle components, adapt to the vehicle's high-speed performance, reduce driving noise, and ensure driving safety, handling stability, comfort, and energy efficiency.
1
2
Share

What documents must be carried when driving a motor vehicle on the road?

Documents required for driving on the road: The driver must carry the vehicle license and driver's license, and the compulsory traffic insurance label, vehicle inspection qualification label, and environmental protection label must be affixed to the upper right side of the front windshield. When driving on the road, not only must all relevant documents be carried, but traffic rules must also be followed, and parking must not be done haphazardly. Parking is prohibited in sections with no-parking signs or in areas with isolation measures. Parking is also prohibited on sidewalks, construction sections, bus stops, fire stations, and other intersections. On highways, parking is not allowed in unauthorized areas, or at intersections, tunnels, steep slopes, bridges, and sections within 50 meters of these areas. At intersections, running red lights is prohibited. Vehicles should slow down in advance at traffic intersections and must stop outside the stop line when encountering a stop signal; if there is no stop line, stop outside the pedestrian crossing line. When turning right without traffic lights, pedestrians must be given the right of way.
15
5
Share

Reasons for Insufficient Pressure in a Three-Cylinder Plunger Pump

Insufficient pressure in a three-cylinder plunger pump may be caused by aging of the wash pump. Below are the relevant details: Concept: A three-cylinder plunger pump is a type of equipment primarily used for intermittent operations such as acidification, cementing, fracturing, and well sealing. Features: The pump's reducer can be installed in 17 different positions, allowing it to adapt to various drive configurations of the pump unit; two different pump head bodies are available to accommodate plungers of different sizes (due to varying pressure and displacement requirements); optional packing components, valve assemblies, discharge flanges, and suction manifolds can be selected to meet the requirements of different layouts, media, and environments; the pump has a lightweight and simple structure, with reduced weight, maximum displacement, and highest pressure.
4
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.