What are the precautions during the break-in period of the BMW X3?

1 Answers
StAnthony
07/29/25 5:24pm
Here are the precautions during the break-in period of the BMW X3: Avoid emergency braking: Emergency braking not only harms the braking system during the break-in period but also increases the impact on the engine and transmission. Avoid prolonged high-load driving: Frequently pressing the accelerator deeply will increase the engine load and the shifting impact of the transmission. It is recommended to keep the engine speed below 3000r/min. Do not overload: Overloading makes steering heavier, increases centrifugal force, and affects the car's handling performance; long-term overloading will also shorten the car's lifespan and accelerate the aging of components. A better practice is to keep the load within 70% of the standard capacity.
Was this review help?
4
4
Share
More Forum Discussions

How to use the panoramic sunroof on the Volvo XC90?

Volvo XC90 panoramic sunroof usage method: 1. Fully open the sunroof: There is a sunroof control button located in front of the interior rearview mirror. Push it backward all the way to open the sunroof completely. 2. Tilt the sunroof: To tilt the sunroof, push the button backward while simultaneously pushing it upward. 3. Introduction to Volvo XC90 panoramic sunroof: The Volvo XC90 panoramic sunroof has a length of 1170mm and a width of 700mm, with an openable length of 370mm. The daylighting area is 0.82 square meters, and the openable area is 0.26 square meters.
8
5
Share

Why does an electric vehicle display excessive motor temperature?

Electric vehicles display excessive motor temperature for the following reasons: 1. Excessive power supply voltage: When the power supply voltage is too high, the motor's back electromotive force, magnetic flux, and magnetic flux density all increase. Since the iron loss is proportional to the square of the magnetic flux density, the increased iron loss leads to overheating of the iron core. 2. Insufficient power supply voltage: When the power supply voltage is too low, if the motor's electromagnetic torque remains unchanged, the magnetic flux will decrease, the rotor current will increase accordingly, and the load current component in the stator current will also increase, resulting in higher copper losses in the windings and causing overheating of the stator and rotor windings.
4
2
Share

Which Generation of Honda CB400 is Recommended to Buy?

It is recommended to buy the fourth generation of Honda CB400. Below is an introduction to motorcycle-related content: 1. Working Principle: When the pedal is pressed, the mechanism pressurizes the spring, causing the outer edge of the spring to lift and the pressure plate to disengage from the friction plate. At this point, the friction plate and the flywheel can no longer be linked. Even if the engine continues to run, power will not be transmitted to the gearbox and wheels, allowing the rider to shift gears or stop without stalling the engine. 2. Power Transmission: When the crankshaft speed is low, the two friction plates do not contact the outer shell, preventing power transmission. When the crankshaft speed is high, centrifugal force causes the friction plates to move outward and contact the outer shell, enabling power transmission.
8
1
Share

How to Use the Passat Windshield Wipers?

Push the lever inward to automatically spray washer fluid; the right side is the rear wiper control area, rotate the switch to the corresponding position to activate it. Precautions for using wipers: 1. Maintain Cleanliness: When there are streak marks on the glass surface, the wiper blade may be dirty. Spray a small amount of alcohol on a towel and wipe the dirty areas and spots with residue. Cleaning once a month can improve the wiper's performance. 2. Check the Rubber: If there is unusual noise from the windshield, it may be due to hardening, wear, or cracks in the wiper blade rubber. If the wear is not severe, you can sand it with sandpaper. 3. Avoid Sunlight: Try to park the car in a ventilated and shaded area.
9
3
Share

What does RNDP gear mean?

RNDP stands for Reverse, Neutral, Drive, and Parking gears. Below are the specific details: 1. P (Parking) gear: Used when the engine is off or the car is stationary. The vehicle must be shifted into P gear before powering off, removing the key, or locking the doors. Once in P gear, the vehicle's braking system is engaged, preventing movement even on slopes. 2. R (Reverse) gear: Functions the same as the reverse gear in a manual transmission. 3. N (Neutral) gear: Equivalent to the neutral gear in a manual transmission, used when parking. Another use is to shift into N gear if you need to restart the engine while the vehicle is moving. 4. D (Drive) gear: The forward gear, commonly used for normal driving and one of the most frequently used gears.
18
5
Share

Is the entire paint surface completely scraped off during car touch-up painting?

Car touch-up painting involves completely scraping off the entire paint surface. Here are the detailed aspects regarding car touch-up painting: 1. Reason: Repainting increases the thickness of the paint film, and the repainted area will be higher than the original paint surface. Therefore, the original paint must be removed before repainting. If the original paint is not removed, it will be difficult to polish the subsequent paint. 2. Precautions: The car's primer is an electroplated layer and serves as the main anti-corrosion layer of the car, which must not be damaged. If the car's primer is damaged, the underlying steel plate of the car will gradually corrode and become prone to rust. For minor scratches that do not reach the primer, polishing can be directly used for restoration.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.