···
Log in / Register

What are the precautions and details for Subject 2 driving test?

4 Answers
StJameson
09/08/25 7:13am
Subject 2 driving test requires paying attention to frequent observation of rearview mirrors. Here is relevant information: Introduction to Subject 2: Subject 2, also known as the minor road test, includes five test items: reverse parking into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving through curves. Precautions: When performing reverse parking into a garage, pay attention to observing the rearview mirrors to accurately gauge the distance between the rear wheels and the two lines of the garage in the mirrors. For parallel parking, drive the car to a position parallel with the garage, then move backward to the right to enter the garage. Do not stop during the maneuver, as stopping will result in test failure.
Was this review help?
15
0
Share
OJaxon
09/20/25 5:42am
On the day of my Subject 2 test, I was extremely nervous, but I passed in the end. Here are some tips. Wearing the seatbelt is the top priority—failing to do so means an immediate fail. Remember to adjust the rearview mirrors to ensure you can see the blind spots behind, not just what's in front. When doing reverse parking, operate slowly, keeping the speed below 10 km/h, and align with the yellow line markings on the ground—rushing can easily lead to crossing the line. For parallel parking, observe the position of the front of the car and don’t get too close to the edge of the parking space; the right angle will get you in smoothly. On the slope for the hill start, be steady—release the clutch slowly to prevent the car from rolling back, or you’ll lose significant points. Stay calm mentally, practice mock tests often, and familiarize yourself with the test environment to minimize mistakes. In short, details determine success, and safe driving habits start here—don’t underestimate every small step.
Was this review help?
3
0
Share
Expand All
AlexanderLee
11/03/25 6:05am
I've coached many students for the Subject 2 driving test, and the key is not to make mistakes in basic maneuvers. Always fasten your seatbelt tightly and adjust the rearview mirrors to clearly see the rear of the car. Take a deep breath before starting, control your speed well, and focus on the marking lines when reversing into the parking space—going too fast can easily lead to hitting the poles or going out of bounds. For parallel parking, pay attention to the wheel positions and keep the wheel spacing even. On the slope, align with the designated point, gently release the clutch to prevent rolling back, and don't rush to accelerate. Remember to use the turn signal for right-angle turns; neglecting this will cost you points. Stay focused on each step during the test, don't be distracted by the examiner, and practice simulations to reduce nervousness. Developing good habits is crucial for future driving safety.
Was this review help?
7
3
Share
Expand All
DePreston
12/17/25 6:05am
During the test, I pay the most attention to operational details. After fastening the seatbelt, adjust the seat and rearview mirrors, and check the blind spots. Slow down when reversing into the garage, align with the corner when turning the steering wheel, and observe the ground yellow lines. For parallel parking, watch the distance from the curb and avoid the wheels crossing the line. For hill start, firmly press the clutch, align the position, and pull the handbrake. For curve driving, turn the steering wheel smoothly without sudden movements. Control the speed throughout to avoid stalling or crossing lines. Remember, small mistakes accumulate and can lead to failure, so familiarize yourself with the test course layout during practice.
Was this review help?
8
1
Share
Expand All
More Forum Discussions

How to Repair a Cracked Windshield?

Here are the methods to repair a cracked windshield: 1. Clean the area to be repaired with alcohol and glass cleaner, then blow out all small glass fragments to smooth the damaged area; 2. Use the positioning sticker from the repair kit, position it correctly, and then drip in the glass repair solution, being careful not to squeeze too much; 3. Prepare the syringe, pull it to the top, then block the opening at the bottom of the syringe and hold for about 10 minutes until all bubbles escape. This ensures no air remains in the damaged area; 4. Reinsert the syringe into the bracket, this time pressing it down to push the repair solution into the cracked area. Hold for 15 minutes to allow the solution to penetrate the crack; 5. After 15 minutes, replace with the curing film and use a blade to squeeze out any bubbles. Note that the resin hardens under UV sunlight, not heat. Finally, park the car in the sun for 15 minutes; 6. Finally, remove the curing film and use a blade to scrape off any remaining adhesive.
8
3
Share

Are Racing Cars Manual or Automatic?

Racing cars are generally manual. Racing tests the driver's skills, which are not just about the racing line but also include gear-shifting techniques. For the same corner, some drivers can take it in third gear while others must use second gear, depending on the driver's judgment. Hence, manual transmissions are preferred. The reasons racing cars use manual transmissions are as follows: 1. Manual transmissions are easier to control and more efficient: The advantage of manual transmissions lies in their reliability. Automatic transmissions do not fully allow the driver to control acceleration and deceleration; instead, they determine gear changes based on the machine's operating state. Automatic transmissions use hydraulic drive for power transmission, meaning gear changes cannot occur unless the required RPM is reached. Manual transmissions, on the other hand, are more mechanical, requiring the driver to judge gear changes, making the timing more reasonable. 2. Simpler maintenance and repairs: Manual transmissions have evolved to a point where both production and repair technologies are highly mature. Early cars were equipped with mechanical transmissions, now known as manual transmissions, so this advantage has persisted—simple maintenance and high flexibility in shifting. If an automatic transmission encounters issues, repairs can be complicated, potentially delaying race time. 3. Faster acceleration with manual transmissions: With the same engine, manual transmissions accelerate faster than automatics. Racing cars typically have high-horsepower engines. Comparing similar models, automatic transmissions may provide stronger initial acceleration, but as output RPM increases, their torque transmission declines. This is mainly because manual control of gear changes is more responsive than automatic control. 4. Manual transmissions offer better adaptability: Some racing events, like rally races, take place on dirt roads. When encountering a shallow water pit, a manual transmission car can pass through at a low gear while maintaining throttle, preventing water from being sucked into the vehicle. Automatic transmission cars, however, need to calculate the optimal path, which can be time-consuming.
6
5
Share

What Causes Idle Vibration?

Causes and solutions for car vibration during idle are as follows: 1. Severe engine carbon buildup: The most common cause of car vibration is a dirty throttle body or excessive carbon deposits on the fuel injectors. When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold-start injector is largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts and making it difficult to start. In this situation, the engine will only start easily once the carbon deposits have absorbed enough gasoline. After starting, the gasoline adsorbed on the carbon deposits is then drawn into the combustion chamber by the engine's vacuum, enriching the air-fuel mixture. This fluctuation between lean and rich mixtures causes idle vibration after a cold start. 2. Ignition system issues: Check the condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or spark plugs can also lead to such symptoms. 3. Unstable fuel pressure: If you have already cleaned the engine carbon deposits, throttle body, and replaced the spark plugs but still experience idle vibration, it is recommended to check the fuel supply pressure and the intake pressure sensor. Abnormal fuel pump pressure or incorrect readings and poor performance of the intake pressure sensor can also cause car vibration.
4
1
Share

How to Use Full-Speed Adaptive Cruise Control?

Full-speed adaptive cruise control (ACC) is used as follows: 1. ACC Activation/Deactivation: Press the ACC switch button to turn on the adaptive cruise control system. 2. Set Following Distance: Press the decrease or increase following distance button to reduce or increase the distance between your vehicle and the vehicle ahead. 3. Speed Up: If the cruise control system is already enabled, briefly roll the button toward RES and then release it to increase speed. Below is more information about full-speed adaptive cruise control: 1. Full-speed adaptive cruise control allows the vehicle to be activated from a standstill, maintain a safe following distance, and even follow the vehicle ahead to stop and start. 2. Full-speed adaptive cruise control provides adaptive cruise functionality across the entire speed range.
1
4
Share

Does Coasting in Neutral Save Fuel?

Coasting in neutral does not save fuel and can sometimes even consume more fuel, primarily due to the working mechanism of fuel-injected engines. Fuel-injected engines determine the amount of fuel injection based on computer programming. When the car is in gear and the driver releases the accelerator, the computer puts the vehicle into coasting mode, during which the engine does not inject fuel for a significant period. However, if neutral is selected, the computer switches the vehicle to idle mode, and the engine continues to inject fuel. This is why coasting in neutral can sometimes use more fuel. Additional Information: 1. When a vehicle is coasting in neutral, the connection between the engine and the drive wheels is lost. The car moves forward by its own inertia, and the engine can no longer provide resistance to the drive wheels. In such a situation, if an emergency occurs, the entire braking force must be provided by the brakes alone. However, the braking force that the brakes can provide is limited, leading to longer stopping distances and an increased risk of accidents. 2. For older car models, coasting in neutral could indeed save some fuel, which led many drivers to develop a habit of shifting to neutral whenever possible. However, nowadays, fuel-injected engine models have become mainstream in the market. Therefore, the answer to whether coasting in neutral saves fuel is clear: it does not save fuel and can sometimes consume more, in addition to being detrimental to driving safety.
10
2
Share

What does Hill Descent Control mean?

Definition of Hill Descent Control: It enables the driver to smoothly navigate steep downhill sections without pressing the brake pedal, maintaining full control. The Hill Descent Control (HDC) system, also known as the Slope Control System, primarily functions to maintain a low vehicle speed and ensure tire traction on steep downhill roads, allowing the car to safely descend to flat ground. Once the Hill Descent Control is activated, the driver can release all pedals and focus solely on steering. The correct way to use Hill Descent Control is as follows (using the Volkswagen Teramont as an example): 1. In the Teramont's driving modes, select Off-Road Individualization, then enable the [Downhill Assist System] in the menu. At this point, the function indicator light on the dashboard will illuminate. 2. If the Teramont's Hill Descent Control is always enabled, it will automatically activate when the following conditions are met: vehicle speed below 30km/h, slope gradient ≥10%, and no brake or accelerator pedal pressed. If any condition is unmet, the system will automatically standby. 3. Once Hill Descent Control is activated, the driver does not need to operate the accelerator or brake. The downhill speed control range is 2~30km/h. When entering a downhill section at a speed below 30km/h, the driver can adjust the speed within this range by pressing the accelerator or brake.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.