What are the new regulations for the C1 driver's license?

1 Answers
MacEliana
07/29/25 10:16pm
C1 driver's license new regulations cancel the hill-start test in Subject 2. Below is a brief introduction about the C1 license: Basic Information: The C1 driver's license is one of the license codes. Applicants can apply for the license directly with their resident ID card anywhere in the country without submitting proof of residence registration. The test subjects include four items: traffic regulations and related knowledge, field driving, road driving, and safe and civilized driving knowledge. Driving Requirements: According to the 'Regulations on the Application and Use of Motor Vehicle Driver's Licenses,' the C1 license allows driving small and micro passenger vehicles, light and micro cargo vehicles, and light, small, and micro special-purpose vehicles. Small passenger vehicles must have a seating capacity of 9 or fewer. According to this standard, the C1 license cannot drive vehicles with more than 9 seats.
Was this review help?
17
2
Share
More Forum Discussions

Does the Toyota Vios have a reverse radar?

Toyota Vios does not have a reverse radar. The reverse radar is a safety auxiliary device when the car is parked or reversing. It can inform the driver of the surrounding obstacles through sound or more intuitive display, eliminating the troubles caused by the driver's inspection of the front, rear, left, and right when parking, reversing, and starting the vehicle. Taking the 2021 Toyota Vios as an example, it belongs to a small car, with a body size of: length 4435mm, width 1700mm, height 1490mm, and a wheelbase of 2550mm. The 2021 Toyota Vios engine is equipped with a 1.5L naturally aspirated engine, with a maximum power of 81kw, a maximum power speed of 6000rpm per minute, a maximum torque of 138nm, and is matched with a 5-speed manual transmission.
3
3
Share

What Causes the Abnormal Noise from the Right Front Wheel of a Sedan?

The causes of abnormal noise from the right front wheel of a sedan are: 1. Failure of the front shock absorber; 2. Loose front wheel drive half-shaft; 3. Loose chassis screws and rubber components; 4. Loose ball joints and bearings; 5. Cracked wheel hub bearing; 6. Lack of grease in the wheel hub; 7. Bent steering tie rod. The inspection steps for abnormal noise from the right front wheel of a sedan are: 1. Use a lift to raise the vehicle; 2. Check whether the front-end screws and rubber components of the chassis are loose; 3. Inspect the shock absorber for proper condition before disassembly; 4. Remove the front wheel to check the bearing; 5. Check whether the front wheel drive half-shaft is loose; 6. Determine the cause of the fault and replace the faulty parts.
4
3
Share

Does the Leiling have a hybrid model?

The Leiling has a hybrid model. Taking the Leiling Twin Engine 2021 Basic Edition as an example, it belongs to a compact 4-door 5-seater sedan with body dimensions of: length 4640mm, width 1780mm, height 1455mm, and a wheelbase of 2700mm. The Leiling Twin Engine 2021 Basic Edition is equipped with an ECVT continuously variable transmission. Its front suspension uses a MacPherson strut independent suspension, and the rear suspension uses an E-type multi-link independent suspension. The Leiling Twin Engine 2021 Basic Edition is powered by a 1.8L naturally aspirated engine, with a maximum power of 72 kW at 5200 rpm, a maximum torque of 142 Nm at 3600 rpm.
4
3
Share

What is the lifespan of an Aisin 6AT transmission?

The lifespan of an Aisin 6AT transmission is approximately 200,000 kilometers. The transmission, also known as a gearbox, is a mechanism used to alter the speed and torque from the engine, and it can fix or change the gear ratio between the output shaft and the input shaft. The functions of the transmission are: 1. To change the transmission ratio and expand the range of torque and speed variation of the driving wheels; 2. To enable the car to reverse while maintaining the same rotation direction of the engine. Types of transmissions include: 1. Manual transmission; 2. Automatic transmission; 3. Semi-automatic transmission; 4. Continuously variable transmission. Maintenance methods for the transmission are: 1. Check the quality and quantity of the oil at intervals specified by the manufacturer; 2. Regularly replace the oil with products that meet the manufacturer's specifications; 3. Have the transmission serviced at a professional repair facility.
12
2
Share

Does mixing 98 octane and 95 octane gasoline have any impact?

Mixing 98 octane and 95 octane gasoline does have an impact. The effects of mixing them are: 1. Shortening the service life of the car's ignition system, fuel injectors, and spark plugs; 2. Advancing the timing of major vehicle repairs; 3. Causing unstable power output in the vehicle; 4. Increasing tailpipe pollution and harming the environment. 92 octane and 95 octane gasoline cannot be mixed because doing so affects the normal operation of the engine, leading to increased noise, reduced driving power, and engine damage. Gasoline is a volatile, flammable hydrocarbon mixture liquid derived from the fractional distillation, cracking, or pyrolysis of petroleum, used as fuel. The characteristics of gasoline are: 1. Volatility: It rapidly vaporizes in the engine cylinder and forms a uniform combustible mixture with air; 2. Stability: The ability to resist oxidation under normal temperature and liquid-phase conditions is called stability.
16
0
Share

What is the purpose of using a tensioner pulley for the drive belt?

The purpose of using a tensioner pulley for the drive belt is to adjust the initial tension of the belt. The tensioner pulley mainly consists of a fixed housing, tensioner arm, wheel body, torsion spring, rolling bearing, and spring bushing, etc. It can automatically adjust the tension according to the different tightness levels of the belt, ensuring the transmission system is stable, safe, and reliable. The tensioner pulley uses a spring or hydraulic pressure to generate a force that tightens the belt, allowing the belt to press against the working pulley with appropriate pressure. Precautions for the tensioner pulley are: 1. The tension force of the tensioner pulley should not be too small, as insufficient tension will reduce the friction between the belt and the working pulley, eventually causing the belt to slip; 2. The tensioner pulley should generally be placed on the inner side of the slack side, so that the belt is subjected to only one-way bending, and it should also be as close as possible to the large pulley to avoid excessively affecting the wrap angle of the small pulley.
2
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.