What Are the Motorcycle Riding Techniques?

1 Answers
HavenDella
09/09/25 2:13am
When going uphill, always select the appropriate gear to keep the engine at a reasonable RPM and optimal power output. Avoid excessive throttle; if it's too much, you can downshift. When riding in mountainous areas, riders can assess the road conditions ahead based on the environment, such as the direction of the mountain wall. Slow down before entering a curve, and avoid braking during the curve. Before entering a curve, always stay to the right and sound your horn as a signal. Never overtake in a curve. Slowing down before entering a curve is essential.
Was this review help?
15
0
Share
More Forum Discussions

What Causes Slow Cooling in Car Air Conditioning?

Slow cooling in car air conditioning may be caused by insufficient refrigerant due to low levels. The detailed reasons are as follows: Insufficient refrigerant due to low levels: The primary cause of insufficient refrigerant is typically minor leaks in the system. If the refrigerant level in the air conditioning system is low, the amount of refrigerant sprayed into the evaporator from the expansion valve will also decrease. As a result, the refrigerant absorbs less heat during evaporation in the evaporator, leading to reduced cooling capacity. Moisture infiltration in the air conditioning refrigeration system: There is a component in the refrigeration system called the dryer (or receiver-drier), whose main function is to absorb moisture from the refrigerant to prevent excessive moisture from reducing cooling efficiency. However, when the desiccant in the dryer becomes saturated, it can no longer filter out moisture. As the refrigerant passes through the expansion valve's throttle orifice, the pressure and temperature drop, causing the moisture in the refrigerant to freeze in the small orifice. This can obstruct refrigerant flow, increase resistance, or even block it completely. Reduced heat dissipation capacity of the condenser: Due to varying working environments, the condenser located in front of the car engine may become covered with oil, dirt, or debris, reducing its heat dissipation capacity. Additionally, issues with the cooling fan, such as a loose drive belt, reduced fan speed, or high-speed fan problems, can also impair the condenser's heat dissipation. The solution is to clean the condenser surface with a soft brush and promptly address any fan malfunctions.
7
5
Share

How to operate the central control screen of Changan CS55?

The basic function settings and adjustments of the vehicle are in the settings. In the system settings, you can connect to a wireless hotspot. Once connected, if a player is installed, you can access the internet and watch movies. Connecting Bluetooth allows you to answer calls via the central control.
7
1
Share

What to Do When the Car AC Keeps Turning Off Automatically?

Check if the timer switch option on the AC remote control is turned on. If so, please turn it off. Check if the remote control is in sleep mode, where it will automatically turn off when the temperature reaches the adjusted setting. Switch this mode back to normal mode. The issue might be due to poor contact between the pins and sockets of the AC pipeline. Try unplugging the AC switch and inserting it into other pins to see if it still turns off automatically.
10
1
Share

How to turn off the rear wiper of the Tiguan L?

The switch for the rear wiper of the Tiguan L is located behind the steering wheel, which is the same as the front wiper switch. The front wiper works by moving up and down, while the rear wiper works by pushing forward and backward. There is an 'off' position on the switch, and placing it in this 'off' position will turn it off.
1
1
Share

What to Do When Driving Through Water

When driving through a waterlogged section, first assess whether it's passable. Always check the water level marker before entering a tunnel. Do not enter blindly without checking the water level marker. Drive slowly at low speed; never speed through. High speed can easily cause water to splash into the engine or other components. Starting the car in a large area of standing water will directly cause water to flow into the engine, and even continuously enter the cylinders through the intake pipe, causing the cylinders to fail.
13
4
Share

How to Perform Sheet Metal Work on Aluminum Car Bodies?

Use a flame torch to heat the car body, softening the aluminum alloy body to facilitate better pulling. Once the dented area is softened, pulling work can be performed, accompanied by hammering during the pulling process. After repairing the dented area, use a file and a grinder to smooth out the surface, ensuring it is even.
9
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.