What are the methods to solve the door rattling noise when driving on bumpy roads?

2 Answers
TaylorLynn
07/24/25 3:20am
To solve the door rattling noise when driving on bumpy roads, you can follow these steps: 1. Check if the door seal is aging and consider replacing it; 2. Inspect the door gaps for any foreign objects and clean them if necessary; 3. If the noise is caused by loose components between the door parts, tightening the screws may solve the issue; 4. Insufficient body stiffness may cause deformation during driving, leading to friction or shaking between the door and frame, or even friction between steel plates due to welding failure—it is recommended to visit a repair shop for professional handling. The possible causes of door rattling noise on bumpy roads include: 1. Squeaky hinges; 2. Aging door seals; 3. Small objects inside the door trim panel; 4. Loose interior trim panels or audio components.
Was this review help?
5
0
Share
DanielaFitz
08/10/25 10:54pm
The rattling noise from car doors on bumpy roads is quite annoying, and I used to encounter it frequently. The solution is to first check if the door seals are aged or have dust trapped in them. Simply wipe them clean with a towel dipped in water; if they’ve hardened, you can spray some rubber lubricant for immediate effect. Next, inspect the door hinges and latches—over time, screws may loosen, so use a wrench or pliers to tighten them slightly to prevent movement-induced noise. If the door trim panel is loose, open the inner panel to check the clips or screws and reinforce them. Parking on level ground can reduce wear, and addressing noises promptly prevents discomfort and distraction while driving. A simple DIY fix saves money and brings peace of mind.
Was this review help?
16
1
Share
Expand All
More Forum Discussions

What is Four-Wheel Alignment?

Four-wheel alignment is based on the four-wheel parameters of the vehicle, adjusted to ensure good driving performance and certain reliability. The installation of the steering wheels, steering knuckles, and front axle of a car has a specific relative position, which is called steering wheel alignment, also known as front-wheel alignment. Front-wheel alignment includes four aspects: caster angle, kingpin inclination angle, camber angle, and toe-in. Rear-wheel alignment includes camber angle and individual rear-wheel toe-in. Collectively, this is referred to as four-wheel alignment. Its purpose is to maintain stable straight-line driving, facilitate easy steering, and reduce wear on tires and steering components during driving. Below are relevant details: Functions: Front-wheel alignment includes caster angle, kingpin inclination angle, camber angle, and toe-in. Rear-wheel alignment includes camber angle and individual rear-wheel toe-in. Together, front-wheel and rear-wheel alignment are called wheel alignment, commonly known as four-wheel alignment. The role of wheel alignment is to keep the car driving straight stably, make steering easier, and reduce wear on tires and steering components during driving. Caster Angle: Viewed from the side, the steering kingpin (the rotation center when the wheel turns) tilts backward, which is called the caster angle. After setting the caster angle, a distance is created between the contact point of the kingpin centerline and the ground projection point of the wheel center (called the caster trail, similar to the backward tilt of a bicycle's front fork). This positions the wheel's contact point at the rear end of the kingpin's extension line, pulling the wheel backward due to rolling resistance during driving, naturally aligning the wheel with the driving direction. A large caster angle improves straight-line driving performance but also increases the caster trail. An excessively large caster trail can make the steering wheel heavy and worsen the wheel's bouncing due to road disturbances.
5
4
Share

Does a Newly Purchased Car Need Antifreeze in Winter?

Newly purchased cars do not require additional antifreeze for winter. This is because new vehicles come with factory-installed antifreeze, which typically only needs replacement every two years or every 30,000 kilometers. The antifreeze replacement procedure is as follows: Before completely replacing the antifreeze, conduct a thorough inspection to check for any signs of leakage or cracks in the pipes, with particular attention to the five-way water pipe. Antifreeze is distributed to different parts of the car through this five-way pipe to perform its function. If there is any antifreeze leakage in this section, replace the water pipe or resecure the connection as needed. Drain the old antifreeze, then flush the liquid channels with clean water. Add clean water to the antifreeze reservoir, then continue adding water to the reservoir so that it continuously flows through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. Initially, the water draining from the reservoir will have a faint pink color. Continue adding clean water until the outflowing water is clear. Note: Remember to remove the heater hose and drain all water from the heater core. Approximately one hour after draining, add new antifreeze through the radiator hose. Then, add another container of antifreeze to the antifreeze reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. During this time, the coolant level will drop slightly as air is expelled from the cooling system. Top up the antifreeze until it reaches the "MAX" mark on the reservoir.
3
5
Share

Can Seat Heating Be Installed Aftermarket?

Seat heating can be installed aftermarket. Additional information about seat heating is as follows: 1. The seat heating function utilizes electric heating wires inside the seat to warm the interior, transferring heat to the occupant through thermal conduction. This improves comfort in winter when seats become uncomfortably cold after prolonged parking. 2. Seat heating products differ from other car seat cushions. Their performance and stability directly affect vehicle safety. If the heating pad quality is substandard, continuous high-temperature heating can easily cause the cushion to spontaneously combust, leading to fire hazards. 3. Uneven wiring or improper installation of heating pads can also result in spontaneous combustion incidents.
16
0
Share

How to Turn On the Low Beam Headlights on a Civic?

The method to turn on the low beam headlights on a Civic is: Locate the lighting combination switch on the left side of the steering wheel and rotate it forward two notches to turn them on. Below is more information about the Civic: 1. Vehicle Dimensions: It is a compact car under Dongfeng Honda, with body dimensions of 4658mm in length, 1800mm in width, and 1416mm in height, a wheelbase of 2700mm, and a fuel tank capacity of 47 liters. 2. Powertrain: The Civic Shangyue edition is equipped with a 1.0L turbocharged engine, delivering a maximum horsepower of 125 PS and a maximum power speed of 5500 rpm, paired with a continuously variable transmission (CVT).
5
4
Share

What does the anti-knock property of automotive gasoline mean?

The anti-knock property of automotive gasoline refers to the ability of gasoline to resist abnormal combustion (knocking) in the engine cylinders. Therefore, additives are mixed into gasoline to enhance its anti-knock properties. Additional information about gasoline anti-knock properties is as follows: 1. Strong anti-knock properties allow the use of higher compression ratio engines, which can improve engine power, reduce fuel consumption, and enhance the engine's economic efficiency. 2. To improve gasoline's anti-knock properties, tetraethyl lead additives are typically added to gasoline. Since tetraethyl lead is toxic, gasoline containing it is often dyed red for distinction to prevent misuse and poisoning.
5
1
Share

How often should a Volkswagen Passat be serviced?

The normal service interval for the new Passat is every 7,000 kilometers. Car owners who cherish their vehicles typically change the engine oil and oil filter every 5,000 kilometers, depending on the owner's needs. More details are as follows: 1. Car maintenance refers to the preventive work of regularly inspecting, cleaning, replenishing, lubricating, adjusting, or replacing certain parts of the vehicle, also known as car servicing. 2. Modern car maintenance mainly includes the engine system, transmission system, air conditioning system, cooling system, fuel system, power steering system, and other maintenance areas. 3. The purpose of car maintenance is to keep the vehicle clean and tidy, maintain normal technical conditions, eliminate potential hazards, prevent faults, slow down the deterioration process, and extend the service life.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.