What are the methods and sequence for car paint polishing?

1 Answers
LePresley
07/30/25 1:16am
Here is an introduction to the methods and sequence of car paint polishing: 1. Wash the car: Before polishing, it is essential to thoroughly clean the car body to remove dust particles, preventing secondary damage to the paint. 2. Sanding: After washing the car, perform a rough sanding on the body. Depending on the size of surface imperfections or scratches, use water sandpaper of different sizes for sanding. 3. Polishing: After sanding, select an appropriate polishing machine along with polishing wax to perform detailed polishing on the sanded body. 4. Mirror restoration: After polishing, use a mirror treatment agent to restore the mirror-like effect of the car body, followed by waxing and shining.
Was this review help?
1
4
Share
More Forum Discussions

What is the difference between 95 and 92 gasoline prices?

95 gasoline is slightly more expensive than 92 gasoline. This is because 95 gasoline has a higher octane rating and fewer impurities, resulting in higher refining costs. Generally, the fuel tank of a vehicle will have the gasoline grade recommended by the manufacturer. You just need to refuel according to the grade indicated on the fuel tank. Here is some information about 95 and 92 gasoline: 1. 95 gasoline has higher combustion efficiency than 92 gasoline during medium to high-speed operation. However, 92 gasoline is more economical during low to medium-speed operation. 2. The gasoline grade is the ratio of the actual gasoline's anti-knock performance to that of standard gasoline. The higher the grade, the stronger the anti-knock performance. 95 gasoline has a higher octane rating, while 92 gasoline has a slightly lower octane rating. The octane rating of gasoline directly determines its anti-knock quality.
8
2
Share

What are the reasons why a car cannot be turned off?

The reason why a car cannot be turned off is likely due to damage inside the ignition switch. The ignition switch has ACC, ON, and START positions. Turning to ACC powers the car's electrical equipment; ON powers the ABS (Anti-lock Braking System), AIRBAG (airbag), fuel pump, and ECU power supply, among others; while START is for ignition. Solutions for not being able to turn off the car are as follows: 1. Directly disconnect the fuel line switch. This mechanical fuel line switch varies in location depending on the car model—some are under the seat, while others are on the lower left side of the steering wheel. 2. For electronically controlled diesel engines, similar to car keys, they only power on when in the ON position, with the ECU controlling the fuel injectors to spray fuel. Therefore, turning off the key for such diesel engines stops the fuel injectors, effectively cutting off the fuel supply.
17
5
Share

What are the steps to replace the cabin air filter in a Buick Envision?

The method for replacing the cabin air filter in the Buick Envision is as follows: 1. Open the glove box and remove the fuse box cover. 2. Remove the spring rope buckle, then forcefully pull upward on the plastic beam above the glove box to remove it. 3. Squeeze both sides toward the middle with force to completely remove the glove box, exposing the cabin air filter housing. 4. There are buckles on both sides; open the buckles to lift the housing cover, then remove the old filter and install the new one. Finally, reassemble everything in reverse order. Additional information about the Buick Envision's cabin air filter: 1. Generally, the cabin air filter in the Buick Envision should be replaced every 10,000-15,000 kilometers or once a year. 2. The replacement interval for the cabin air filter mainly depends on the external environment.
12
0
Share

How to turn on the high beam of Nissan Qashqai?

To turn on the high beam of Nissan Qashqai, follow these steps: Turn the end of the light control lever forward to the second gear to turn on the low beam. In the low beam state, gently push the light control lever forward to switch to the high beam. Additional information: 1. It is generally best not to use high beams when driving in the city because the lighting conditions are usually good. The high angle of the high beam can easily dazzle oncoming drivers and pedestrians, affecting their vision and posing safety risks. It is also considered impolite driving behavior. However, alternately turning the high beam on and off at night can replace the horn to alert pedestrians and vehicles around you, avoiding excessive noise. 2. You can use the high beam when driving on highways or in rural areas without streetlights to expand your field of vision. However, when encountering oncoming vehicles, switch to the low beam for safety and courtesy. 3. When driving at low speeds, the engine's power generation is insufficient, and the battery is in a state of negative charging. Using the high beam can affect its lifespan. Additionally, using the high beam at low speeds at night will also increase the vehicle's fuel consumption.
9
3
Share

What are the differences between the Bora and Lavida?

The differences between the Bora and Lavida: 1. Different body dimensions: The Bora's body dimensions are 4663mm in length, 1815mm in width, and 1462mm in height; the Lavida's body dimensions are 4670mm in length, 1806mm in width, and 1474mm in height. 2. Different fuel tank capacities: The Bora has a fuel tank capacity of 50L, while the Lavida has a fuel tank capacity of 51L. Here are the similarities between the Bora and Lavida: 1. Both the Bora and Lavida are equipped with a 7-speed dual-clutch transmission. They both use a McPherson-type independent front suspension and a torsion beam-type non-independent rear suspension. 2. Both feature electric power steering and a unibody structure.
10
4
Share

How to Deal with Fogging in Car Rearview Camera?

A rearview camera is a type of car camera installed at the rear of the vehicle. It works in combination with a display screen installed inside the car to form a complete rearview imaging system, allowing the driver to see real-time video images of the area behind the car when reversing. The solutions for fogging in a car rearview camera are as follows: 1. Surface fogging: Simply wipe it clean with a dry, soft cotton cloth. Generally, avoid using cleaning agents. 2. Internal fogging: Remove the camera and place it in a relatively dry environment. Usually, the moisture will disappear after some time. 3. If necessary, remove it to blow dry the water, then apply some glass glue at the water inlet. Wait for the glass glue to dry for about half an hour before reinstalling it.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.