What are the measures to prevent rear-end collisions?

1 Answers
EmeryLynn
07/30/25 12:00am
Measures to prevent rear-end collisions include: not following empty taxis, not following large trucks, and not following buses (both large and small). Below are the relevant explanations: 1. Do not follow empty taxis: Empty taxis may suddenly brake when the driver spots a passenger. If you follow too closely, the vehicle behind is prone to rear-end collisions. 2. Avoid following large trucks: Large trucks block the view of the road ahead for vehicles behind them. It is common for large trucks to run red lights at intersections, and the following vehicle, unable to see the red light due to the obstruction, may proceed through the intersection, leading to danger. 3. Avoid following buses (both large and small): Similar to large trucks, buses can also obstruct the view. If you follow too closely or drive alongside them, accidents are more likely to occur, with smaller passenger vehicles often bearing the brunt of the damage.
Was this review help?
16
3
Share
More Forum Discussions

Which country does the Haima S8 engine come from?

The engine equipped in the Haima 8S is jointly developed by German FEV and Haima. Below are the relevant details about the Haima S8 engine: 1. The engine model of the Haima S8 is HMAGA16-YF. The actual displacement of the HMAGA16-YF engine is 1594ml, with a turbocharged intake system. It features four cylinders arranged in an L configuration. 2. The HMAGA16-YF engine reaches its maximum power at 5000 rpm and its maximum torque at 4500 rpm. It employs a DOHC valvetrain. The HMAGA16-YF engine is recommended to use 92-octane gasoline and adopts direct fuel injection. 3. The HMAGA16-YF engine delivers a maximum output power of 143 kW and a maximum torque of 293 N·m. It achieves a 0-100 km/h acceleration time of 7.8 seconds, with a combined fuel consumption of 6.9L per 100 km as published by the MIIT.
8
0
Share

What are the dimensions of the new BMW X1?

The dimensions of the new BMW X1 are 4565mm in length, 1821mm in width, and 1620mm in height. Below is a related introduction to the BMW X1: 1. Design: The 2019 BMW X1 remains largely consistent with the previous model, with adjustments made to the headlights and bumper. The headlight structure has been upgraded, with the LED daytime running lights now featuring the latest polygonal design, providing high recognition when lit. The circular fog lights below have been repositioned lower. The air intakes on both sides of the bumper are larger in size and more stylish compared to the current model. The front grille retains BMW's iconic kidney design with black coating, giving the vehicle a cooler appearance. 2. Powertrain: The new X1 continues to be equipped with the existing 1.5T inline three-cylinder engine (18Li model) and 2.0T inline four-cylinder engine (20Li model), delivering maximum power outputs of 136 horsepower and 192 horsepower respectively. The transmission systems are paired with a 6-speed automatic and an 8-speed automatic transmission respectively. The two higher-end models are further equipped with the xDrive all-wheel-drive system.
13
4
Share

What are the differences between the A6 and A8?

The A6 and A8 are two different models produced by Audi. The main differences between the A6 and A8 are as follows: 1. Positioning: The Audi A6 is a mid-size luxury sedan, classified as an executive-level car, while the A8 is the top-tier luxury sedan in Audi's lineup and serves as the brand's flagship model. 2. Body dimensions: The A8L measures 5192mm*1894mm*1455mm with a wheelbase of 3074mm, whereas the A6L measures 5012mm*1855mm*1485mm with a wheelbase of 2945mm. 3. Powertrain: The A6 offers four gasoline engine options: 2.0TFSI, 2.4, 3.2FSI, and 4.2FSI, while the entry-level A8 comes with a 3.2FSI engine, along with two other gasoline engine options: 4.2FSI and W12-6.0.
20
1
Share

What to Do When the Car Key Doesn't Respond to Locking?

The solutions for a car key not responding to locking are: 1. Replace the key battery; 2. Use the mechanical key. The steps to replace the car key battery are: 1. Remove the mechanical key; 2. Insert a flat-head screwdriver into the bottom "open" position and pry it up and down; 3. Once a gap appears, use the screwdriver to pry open the key along the gap; 4. Remove the old battery and replace it with a new one. The functions of the car key are: 1. Press the horn-shaped button to locate the car; 2. After turning off the engine, press and hold the door lock button to close the windows; 3. Remote door lock control. The working principle of the car key is: A weak radio wave is emitted from the owner's side, received by the car's antenna, and after the electronic controller identifies the signal code, the system's actuator performs the action of opening or closing the lock.
7
4
Share

What car is the Tang and Song logo?

The Tang and Song logo represents BYD brand vehicles. BYD Tang and Song are two different models, both compact SUVs, primarily embodying Chinese elements. Below are relevant details about the Tang and Song logos: 1. Configuration: Standard features include ESP, EPB, a dashcam, front dual airbags + front side airbags, front and rear parking radar, an electronic anti-glare rearview mirror, child seat anchors, automatic unlocking upon collision, high-voltage system collision power-off protection, high-voltage system misuse power-off protection, high-voltage system active discharge, and high-voltage system passive discharge. Additionally, except for the base model, all other trims are equipped with TPMS tire pressure monitoring system and front-to-rear side curtain airbags. 2. Powertrain: The BYD Song is equipped with a hybrid system consisting of a 1.5T engine and two electric motors, with one motor positioned at the front axle and the other at the rear axle, enabling four-wheel drive functionality. Moreover, the BYD Song has a pure electric range of 70km and accelerates from 0-100km/h in 4.9 seconds.
6
0
Share

How to Remove the Spark Plugs on a Sagitar?

The method for removing spark plugs on a Sagitar is as follows: After opening the engine cover, unplug the electrical connector of the ignition coil, and also remove the circuit cover of the ignition wire harness. Use a specialized tool to pull out the ignition coil, then you can use a spark plug wrench to remove the spark plug. The structure of the spark plug is described below: 1. Steel Shell: The lower part of the steel shell has fine threads for installation into the cylinder head's spark plug hole. The upper part has an external hex nut for fitting a spark plug socket to tighten or loosen the spark plug. 2. The metal rod is the center electrode. The lower end of the metal rod contacts the upper end of the center electrode through a conductive glass body, and the upper end of the metal rod is equipped with a terminal nut. 3. Between the steel shell and the center electrode, there is a high-alumina ceramic insulator to ensure the center electrode remains insulated when electrified. 4. The lowest part of the steel shell is equipped with a curved side electrode. 5. The middle part of the steel shell's exterior has a copper gasket.
9
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.