What are the maintenance items for a private car at 30,000 kilometers?

Does speeding at the entrance of an average speed check zone count?

Speeding at the starting point of an average speed check zone does not constitute a traffic violation. Average speed monitoring is implemented by setting up two adjacent surveillance points on the same road section. The principle is to calculate the vehicle's average speed on that road section based on the time it takes to pass between the two monitoring points, and then determine whether the vehicle has exceeded the speed limit according to the standard set for that section. If the average speed exceeds the limit by 10% or more, corresponding penalties will be imposed, with varying penalties for different ranges of speeding. Methods to prevent speeding: 1. Use navigation: Turn on mobile or in-car navigation before driving. During highway travel, the navigation system will announce any speeding behavior and also report the presence of traffic enforcement cameras or speed check points along the route. 2. Observe signs: While driving on highways, always pay attention to road signs, including warning signs, directional signs, and road markings, and drive accordingly based on these signals.

15

3

Share

What is the load capacity of the BMW 3 Series?

The BMW 3 Series has a load capacity of 410KG. Regulations regarding load capacity: A 4-axle truck with a total weight of 40 tons was not previously considered as overloading, but now a 4-axle truck exceeding 36 tons is considered over the limit. The new "Regulations on the Management of Over-Limit Transport Vehicles on Highways" will be implemented, with significant changes to the overloading standards. Different load classifications: For a 4.2-meter vehicle, the load capacity is within 5 tons; for a 6.2-meter vehicle, within 8 tons; for a 7.2-meter vehicle, within 10 tons. For vehicles over 9.6 meters, the load capacity can be determined based on the number of axles: single axle (2 bridges) within 15 tons, double axle (3 bridges) within 20 tons, and double axle (4 bridges) within 25 tons.

2

3

Share

What is the air flow rate of the Nissan 1.6 engine?

Nissan 1.6 engine air flow rate shows 1.3-1.64 after the engine warms up, with battery voltage ranging from 0-15. Introduction to air flow: The air flow sensor measures the amount of air inhaled by the engine and inputs the signal to the electronic control unit as the main control signal for fuel injection and ignition control. Function of the air flow meter: The function of the automobile air flow meter is to monitor the amount of air intake by the engine and convert the air intake information into an electrical signal transmitted to the electronic control unit. The electronic control unit uses this signal to determine the fuel injection amount of the engine. The automobile air flow meter affects the engine's power performance. The reason for the damage to the automobile air flow meter is the long-term failure to replace the air filter or the use of inferior air filters, which causes the hot wire of the air flow meter to accumulate dust for too long, resulting in inaccurate or failed resistance value changes. Dust can also cause the throttle to become dirty.

4

0

Share

Honda CRV Throttle Body Matching Method?

Honda CRV throttle body matching method: 1. Ensure the accelerator pedal is fully released. 2. Turn the ignition switch to the ON position. 3. Turn the ignition switch to the OFF position and wait for at least 10 seconds. At this point, confirm the throttle body operation for more than 10 seconds by listening to its movement sound. 3. Start the engine and warm it up to normal operating temperature. 4. Check and confirm that the coolant temperature and other conditions are normal. 5. Turn the ignition switch OFF and wait for at least 10 seconds. 6. Ensure the accelerator pedal is fully released, turn the ignition switch to the ON position, and wait for 3 seconds. 7. Within 5 seconds, quickly repeat the following operation 5 times. a. Fully depress the accelerator pedal. b. Fully release the accelerator pedal. 8. Wait for 7 seconds, fully depress the accelerator pedal, and maintain this state for about 20 seconds until the MIL stops blinking and starts to stay lit. 9. Within 3 seconds after the MIL light turns on, fully release the accelerator pedal. 10. Start the engine and let it idle for a while to complete the matching.

10

5

Share

What is the pressure rating of the radiator cap for the Qingling 2.8t diesel engine?

Qingling 2.8t diesel engine radiator cap pressure is 0.9. Pressure 0.9: A radiator cap rated at 0.9 can withstand a pressure of 0.9 bar. The numbers on the radiator cap, such as 0.9, 1.0, 1.1, etc., indicate the internal pressure value of the cooling system after the engine has warmed up. When the cooling system pressure rises to this value, the pressure valve on the radiator cap will release pressure, allowing some high-temperature vapor to pass through the side pipe of the radiator filler neck into the bottom of the coolant in the expansion tank. If a high-rated radiator cap is replaced with a low-rated one, the engine coolant will enter the expansion tank in large quantities due to the lower pressure rating of the cap, resulting in reduced coolant levels during engine operation and causing high water temperature. Conversely, if a low-rated radiator cap is replaced with a high-rated one, the engine may experience increased internal cooling system pressure during operation due to the higher pressure rating of the cap. This elevated pressure can easily lead to leaks (such as radiator leaks, hose connection leaks, cylinder head gasket leaks, etc.).

4

5

Share

How to Exit the Highway Without Taking a Card?

When exiting the highway, pay the full toll from the entry point to the exit point, and you can leave the highway. Below are specific instructions for entering the highway: Card Collection Process: The card dispenser or manual toll booth will be on the left side of the vehicle. Drive close to the left in advance and visually estimate the distance between the left corner of your vehicle and the card dispenser or toll booth. After adjusting the left and right distance, keep the steering wheel straight and proceed slowly without swaying left or right. When the card dispenser or toll exit is directly aligned with your left shoulder, stop the vehicle, shift to neutral, or engage the handbrake. Press the corresponding button based on your vehicle type and then take the card. Below is additional information: Toll Standards: Depending on the type of vehicle, highways implement a classified toll standard, which is indicated by the numbers 1 and 2 on the card dispenser. 1 represents sedans and small passenger vehicles with 7 seats or fewer, as well as small trucks weighing 2 tons or less. 2 represents passenger vehicles with 8 to 19 seats and trucks weighing more than 2 tons up to 5 tons (inclusive).

13

1

Share

What are the maintenance items for a private car at 30,000 kilometers?

Does speeding at the entrance of an average speed check zone count?

What is the load capacity of the BMW 3 Series?

What is the air flow rate of the Nissan 1.6 engine?

Honda CRV Throttle Body Matching Method?

What is the pressure rating of the radiator cap for the Qingling 2.8t diesel engine?

How to Exit the Highway Without Taking a Card?

Reasons for Unresponsive Buttons on the Envision Steering Wheel?

What is the fuel consumption of the Passat 330?

How to Transfer Ownership of a Gifted Vehicle?

How long after a car insurance expires can it not be purchased?