What are the main reasons for high engine fuel consumption?

1 Answers
McFaith
07/29/25 4:15pm
Engine fuel consumption may be high due to excessive carbon deposits in the engine, damaged oxygen sensors, long overdue replacement of the "three filters," or issues with the engine's electronic control unit. Excessive carbon deposits in the engine: In the short term, excessive carbon buildup in the engine is mainly caused by the use of unsuitable fuel, which is more likely to occur after long-distance driving. Cleaning the carbon deposits can resolve the issue. Damaged oxygen sensor in the vehicle: As an internal control unit of the car, the oxygen sensor primarily monitors the fuel-air ratio in the engine. Once damaged, it can cause an imbalance in the fuel-air ratio, leading to a sudden increase in fuel consumption. In such cases, it is necessary to visit a 4S shop for repair or replacement. Long overdue replacement of the "three filters": During vehicle use, the three filters (oil filter, air filter, and fuel filter) must be replaced regularly. If not changed for a long time, they become dirty and affect performance, sending incorrect information to the engine control unit, resulting in incomplete fuel combustion and increased engine carbon deposits. Replacing the three filters can address this issue. Issues with the engine's electronic control unit: This can directly lead to difficulties in starting the vehicle, increased fuel consumption, poor power performance, and thick black exhaust emissions. Immediate inspection and repair at a 4S shop are required in such cases.
Was this review help?
10
4
Share
More Forum Discussions

Specific Steps for Evacuating Automotive Air Conditioning System

Below are the specific steps for evacuating an automotive air conditioning system: 1. Connect the high and low-pressure hoses to the compressor's high and low ports respectively, with the middle hose connected to the vacuum pump. 2. Open the high and low-pressure manual valves and start the vacuum pump. 3. Close the high and low-pressure manual valves and observe whether the pressure gauge reading has rebounded. 4. Turn off both the high/low-pressure manual valves and the vacuum pump. Important Notes: 1. Before servicing the AC system, it's essential to remove air and moisture to reduce water content in the system, facilitating fault diagnosis and repair. 2. Creating a vacuum inside the system lowers water's boiling point, allowing moisture to vaporize and be more easily extracted from the AC system.
1
2
Share

Can I Transfer to Another Driving School After Enrollment?

No, you generally cannot transfer to another driving school. You can only cancel the exam and re-enroll for training. However, you may change driving schools if the need arises due to issues caused by the driving school. Example: A student who couldn't take the Theory Test (Subject 1) after two months of enrollment due to the school's fault. In such cases, you can report to the traffic management department or relevant authorities to protect your legal rights. Additional Information: 1. After completing Subject 1, if you want to change driving schools due to the school's issues. Since it's the driving school's fault, the student can negotiate with the school. If negotiations fail, you may contact other relevant authorities for mediation. 2. After completing Subject 1, if you want to change driving schools for personal reasons. The difference between these two scenarios lies in whether the request to change schools is made before or after Subject 1. The solution is to negotiate with the driving school. 3. After enrolling in driving school, if you need to change schools due to personal reasons preventing you from attending. Once you've enrolled, you cannot change driving schools. This is because after enrollment, your information is registered in the vehicle management office's exam system under that school in the national network. While instructors can be changed, the school cannot.
12
3
Share

What is the difference between the 330 and 380 engines in the Teramont?

Taking the 2020 Teramont as an example, both the 330TSI and 380TSI models are equipped with a 2.0-liter inline 4-cylinder turbocharged engine, but they have different calibrations. This means that although the engines in both cars are the same, the manufacturer's different calibrations result in different power outputs. Below are the relevant details: 1. The 380TSI has more powerful performance than the 330TSI. The manufacturer's calibrations include adjustments to the engine's air intake and exhaust volumes, ignition timing, fuel injection timing, cylinder bore, etc. 2. The 330TSI model is equipped with a low-power version of the 2.0T inline 4-cylinder turbocharged engine, paired with a 7-speed dual-clutch transmission, delivering a maximum power of 137KW and a maximum torque of 320N·m. The maximum power is achieved at 4100-6000rpm, and the maximum torque is available at 1500-4000rpm. The fuel supply system uses hybrid injection. 3. The 380TSI model is equipped with a high-power version of the 2.0T inline 4-cylinder turbocharged engine, paired with a 7-speed dual-clutch transmission, delivering a maximum power of 162KW and a maximum torque of 350N·m. The maximum power is achieved at 4500-6200rpm, and the maximum torque is available at 1500-4400rpm. The fuel supply system uses direct injection.
11
3
Share

Where is the trunk switch of the Lavida located?

The switch is located near the bumper of the Lavida Plus trunk. Find the middle position there, press it with your finger, and the trunk lock will open. The prerequisite is that the car's central lock must be disengaged first. The remote key can also open the trunk by long-pressing the middle button. Below is some relevant information: 1. Inside the car, there is only an emergency switch on the trunk lid. Normally, if you want to open the trunk from inside the car, you can only use the remote key. Some models may have a switch under the driver's seat or on the driver's door, allowing the driver to open the trunk lid from inside the car. 2. The emergency trunk switch is usually located on the trunk lid, with a small cover that can be opened to reveal a pull wire. Pulling it will open the trunk lid. This emergency switch is used in emergencies and is equipped in every car. To open the trunk lid from inside the car, you can only use the remote key. Nowadays, trunk lid configurations are becoming increasingly diverse, including electric trunk lids and kick-sensing trunk lids. These features better align with people's daily car usage scenarios, enhancing convenience. The kick-sensing opening function is particularly useful when both hands are full, making it easier for the owner to open the trunk.
17
0
Share

What does the A/C in a car mean?

AC is the abbreviation for "Air-conditioning" in English, which refers to the air conditioning system. Pressing the "AC" button activates the air conditioning to adjust the temperature according to the set value, while turning it off only engages the fan without temperature regulation. When you turn on the A/C button in the car, the compressor starts working. If the weather is hot and you want cooling, set the air conditioning to the cold air mode and then press the A/C button to quickly blow cold air, rapidly lowering the temperature inside the car for a cooling effect. Additional Information: 1. In winter, if you want to quickly warm up the car, turning on the A/C button is not very useful. It's important to know that the temperature inside the car increases from the heat generated by the engine after starting, such as the heat from the engine, which is transferred into the car. This has little to do with whether the A/C button is pressed or not, as their functions do not conflict. Therefore, turning it on won't have any effect. 2. The A/C button also has a minor function, which is to defog the windows. When the air humidity is high, entering the car can feel very damp. Turning on the button and blowing air for a while can remove much of the moisture, thereby achieving the function of defogging the windows.
20
2
Share

What is the reason for the improper relative installation position of the camshaft and crankshaft?

An improper relative installation position between the camshaft and crankshaft is caused by misaligned timing marks or a loose belt. Simply aligning the timing marks or tightening the belt can resolve the issue. Below are specific details about the camshaft and crankshaft: 1. The camshaft is a component in a piston engine. Its function is to control the opening and closing of the valves. 2. The camshaft is typically made of special cast iron, though forged components are occasionally used. 3. The main body of the camshaft is a cylindrical rod of the same length as the cylinder group. 4. The crankshaft is the main rotating component of an engine. When connected to the connecting rod, it converts the up-and-down (reciprocating) motion of the connecting rod into a circular (rotational) motion.
9
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.