What are the locations for the Hangzhou Subject 2 driving test?

1 Answers
LaAlexa
09/09/25 3:30am
Hangzhou has three test sites for the Subject 2 driving examination: Fuyang Changkou Large Vehicle Subject 2 Test Site, Fuyang Changkou Small Vehicle Subject 2 Test Site, and Xiaoshan Subject 2 Test Site. Below is relevant information: Subject 2: Also known as the small road test, it is part of the motor vehicle driver's license assessment, specifically referring to the field driving skills examination. For the C1 license (small vehicles), the test items include five mandatory components: reverse parking, parallel parking, hill start, right-angle turn, and curve driving (commonly known as S-turn). Some regions may include a sixth item: highway toll card collection. Teaching objectives: Master basic driving operation essentials, possess fundamental vehicle control capabilities; proficiently grasp basic methods for field and road driving, demonstrate reasonable use of vehicle controls and correct spatial positioning of the vehicle, and accurately control the vehicle's position, speed, and route.
Was this review help?
11
4
Share
More Forum Discussions

How to Open the Hood of a Mercedes-Benz C-Class?

Mercedes-Benz C-Class hood opening steps are as follows: 1. Inside the car at the driver's position, near the left foot area (close to the left front wheel), locate a pull lever. Pull it once to release the hood latch. 2. Move to the front of the vehicle and insert your hand into the gap where the hood has popped up (center of the front end). 3. Feel for a pressable latch inside. Press this switch while simultaneously lifting the hood to fully open it. 4. Above the driver's footwell, there's a red release lever - flip it upward. 5. At the front center of the vehicle, pull the hood release handle that appears, then lift the hood upwards using this handle.
4
3
Share

What does the D gear mean?

D gear stands for Drive gear, and the detailed introduction is as follows: 1. D is the abbreviation of Drive, located after the Neutral position. When the gearshift lever is placed in this position, the hydraulic control system automatically engages the corresponding forward gear circuit based on throttle opening signals and vehicle speed signals. The planetary gear system, under the control of the actuating elements, achieves the corresponding gear ratio. As driving conditions change, it automatically shifts between forward gears (switching between D1 and D4), realizing the automatic transmission function. 2. D gear is the most common gear in automatic transmission vehicles, usually located in the middle-rear position of the gearshift console, behind the N (Neutral) gear. Its purpose is to enable the vehicle to automatically select the appropriate gear while moving forward. 3. Forward gears are not limited to D gear; they also include M (Manual) gear, S (Sport) gear, L (Low) gear, and numerically labeled restricted gears such as 1st, 2nd, and 3rd. Driving gears consist of both forward and reverse gears, while the counterpart to driving gears is Neutral, which means no gear is engaged.
19
3
Share

What Does It Mean When the Red Engine Oil Light Comes On?

The reasons for the red engine oil light coming on are as follows: 1. Insufficient oil level, which reduces the oil pump's output or causes it to fail to pump oil due to air intake, leading to a drop in oil pressure; 2. Overheating of the engine, which can thin the oil, causing it to leak excessively through the clearances and resulting in decreased oil pressure; 3. Damage to the oil pump components or excessive gaps due to wear and tear or improper assembly, which can cause the oil pump to fail to deliver oil or deliver insufficient oil; 4. Improper clearance between the crankshaft and the bearings—too tight will increase oil pressure, while too loose will decrease it; 5. Clogged oil filter or oil suction screen, which can also reduce oil pressure; 6. Damaged or malfunctioning relief valve: If the main oil passage relief valve spring is fatigued, softened, or improperly adjusted, or if the valve seat and ball bearing wear or get stuck by debris, preventing proper sealing, the return oil volume will significantly increase, and the main oil passage pressure will drop accordingly; 7. Incorrect oil selection: Using the wrong oil or an inappropriate grade can increase oil leakage due to low viscosity during engine operation, thereby reducing oil pressure.
11
2
Share

What are the differences between 1.4L and 1.5L?

1.4L and 1.5L differ in the following aspects: 1. Engine Power: The 1.4T is turbocharged, offering stronger power than the 1.5L, but it is more expensive and costs more for maintenance. 2. Engine Power: The 1.5L has weaker power, and cars equipped with 1.5L generally have poorer acceleration performance, but they are cheaper and cost less for maintenance. 3. Engine Power: The 1.4T has better displacement compared to the 1.5L, but it consumes more engine oil. 4. T stands for turbo, meaning turbocharged. L stands for liter, indicating the engine's displacement in liters. Engines marked with L without a T are generally naturally aspirated engines.
16
5
Share

How to activate the anti-pinch function for Nissan Qashqai windows?

To activate the anti-pinch function for Nissan Qashqai windows, follow these steps: 1. Turn on the ignition switch, then lower the window halfway. Press the window switch to raise the window to the top, and keep holding the switch for 1-2 seconds after the window reaches the top; 2. Release the switch. Taking the 2017 Nissan Qashqai as an example, it is a compact SUV with the following dimensions: length 4384mm, width 1837mm, height 1594mm, wheelbase 2646mm, minimum ground clearance 199mm, and curb weight 1358kg. The 2017 Nissan Qashqai is equipped with a 1.2T turbocharged engine, delivering a maximum horsepower of 117PS, maximum torque of 190Nm, and maximum power of 86kW, paired with a 6-speed manual transmission.
14
5
Share

What does 10w30 engine oil mean?

10w30 engine oil refers to a multi-grade viscosity all-weather engine oil. The '10w' indicates the low-temperature viscosity performance of the oil in winter, while the '30' represents its high-temperature viscosity performance in summer. The smaller the number before 'w', the better the oil's fluidity at low temperatures, making it easier to start the car. The larger the number after 'w', the better the oil's viscosity in high-temperature environments, resulting in a stronger oil film. Engine oil is composed of base oil and additives. The base oil is the main component of the lubricant, determining its basic properties, and its functions include: 1. Lubrication and friction reduction; 2. Assisting in cooling; 3. Sealing and leak prevention; 4. Rust and corrosion prevention; 5. Shock absorption and buffering.
4
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.