What are the length, width, and height dimensions of the Wuling Rongguang?

1 Answers
LeNathan
07/29/25 3:19pm
The Wuling Rongguang is a microvan under the Wuling brand. The dimensions of this vehicle are 4135 mm in length, 1625 mm in width, and 1870 mm in height, with a wheelbase of 2700 mm. Additional relevant details are as follows: 1. Engine: The Wuling Rongguang is equipped with two engines—a 1.2L naturally aspirated engine and a 1.5L naturally aspirated engine. The 1.2L naturally aspirated engine delivers a maximum power of 56 kW at 5600 rpm, with a maximum torque of 112 Nm between 3600 and 4200 rpm. This engine features multi-point fuel injection technology and utilizes an aluminum cylinder head with a cast iron cylinder block. 2. Suspension: The front suspension of the Wuling Rongguang employs a MacPherson independent suspension, while the rear suspension uses a longitudinal leaf spring non-independent suspension. Most microvans utilize leaf spring suspensions for the rear suspension.
Was this review help?
9
2
Share
More Forum Discussions

What to Do When the Front Windshield Fogs Up Before Driving?

Window glass fogging can be resolved with the following methods: 1. Turn on the hot air blower to defog the glass. At the same time, switch the air conditioning to external circulation and adjust the vents to defog mode, which will keep the car from getting too cold and also help prevent glass fogging. 2. Apply a layer of anti-fog agent during car washing, then wipe it clean to coat the glass with a protective film, making it less prone to fogging on rainy days. 3. If the front windshield fogs up, roll down the window slightly to let outside air blow in, which will quickly disperse the fog. However, it's best to first pull over to the side of the road, as this defogging process takes some time. 4. Wipe the glass with dish soap or soapy water, then rinse with clean water and dry it off.
16
2
Share

What is the charging method for the Wrangler 4xe?

The Wrangler 4xe can be charged using a charging station. The Wrangler 4xe is built on a 2.0T engine and 8AT transmission, with a lithium-ion battery pack added under the rear seats, assisted by two electric motors to drive the vehicle. For the 4xe, Jeep has developed a new transmission compatible with PHEV and adjusted the lengths of the front and rear drive shafts according to the new transmission's size. More details are as follows: 1. The 4xe's battery pack: The 4xe's battery pack is located under the rear seats, ensuring it does not encroach on the vehicle's interior space. It is protected by the chassis frame below, eliminating concerns about damage from impacts during off-road driving. The battery pack consists of 96 Samsung SDI cells, with a working voltage of 400V and a total capacity of 17kWh, providing the vehicle with a pure electric range of 40km. 2. The ePT control unit: The ePT control unit is positioned on the left side of the drive shaft, responsible for controlling the battery pack and power unit. On the left side of the image, two thick orange high-voltage cables connect to the two electric motors.
19
5
Share

Is the Teana 2.0T engine imported or domestically produced?

The Teana 2.0T engine is a joint venture between Japan and Taiwan. The Teana is assembled at Dongfeng Nissan's factory through the introduction of Nissan's Taiwan joint venture company, making it a domestically produced engine. The model of the Teana 2.0T engine is KR20. The KR20 engine has a maximum horsepower of 243 HP, a maximum power of 179 KW, a maximum power speed of 5400 rpm, and a peak torque of 371 N.m. For daily maintenance of the Teana 2.0T engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected according to mechanical load, with the selection standard not lower than the manufacturer's requirements; Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, causing various problems for the engine. To avoid malfunctions, oil should be changed regularly according to usage conditions, and the oil level should be moderate; When oil passes through the fine holes of the filter, solid particles and sticky substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to bypass through the bypass valve, bringing contaminants back to the lubrication area, accelerating engine wear and internal contamination; Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while large amounts precipitate, clogging filters and oil holes, making engine lubrication difficult and causing wear; Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
5
5
Share

What are the impacts of a faulty oxygen sensor?

Damage to the oxygen sensor can lead to the following consequences: 1. When the front oxygen sensor fails, the ECU cannot obtain information about the oxygen concentration in the exhaust pipe, thus unable to provide feedback control on the mixture concentration. The ECU has no way of knowing the amount of fuel injection and air intake, leading to increased engine fuel consumption and exhaust pollution. The engine may exhibit unstable idling, misfires, surging, and other fault phenomena. 2. A rear oxygen sensor failure means the operating condition of the three-way catalytic converter cannot be determined. If the three-way catalytic converter malfunctions, the exhaust emissions will exceed standards, which could mildly increase fuel consumption and affect engine performance, or severely impact annual inspections or necessitate the replacement of the three-way catalytic converter. 3. Cars usually have two oxygen sensors, one front and one rear. The front oxygen sensor is typically installed on the exhaust manifold, while the rear oxygen sensor is installed behind the three-way catalytic converter. They play different roles in the exhaust system, so the symptoms of failure will also vary.
3
1
Share

Where is the engine model of Volkswagen Teramont located?

The engine model of Volkswagen Teramont can be seen on the engine itself, marked with a steel stamp. The model is EA888 2.0L turbocharged engine. Here is some information about Volkswagen Teramont: 1. Volkswagen Teramont is equipped with an EA888 2.0L turbocharged engine. The low-power version of the 2.0T engine has a maximum power of 137kW (186Ps) and a maximum torque of 320Nm. The high-power version of the 2.0T engine has a maximum power of 162kW (220Ps) and a maximum torque of 350Nm. In terms of transmission, all models are matched with a 7-speed wet dual-clutch transmission, and some models also offer a four-wheel drive system. 2. Teramont not only has a large body, but its interior space is also commendable. Consumers of average size can enjoy ample space in any row, which is a significant advantage compared to its competitors. Moreover, it does not sacrifice trunk space, ensuring practicality.
9
0
Share

What Causes the Failure of the Mercedes Blower Regulator?

Possible causes include a damaged blower or issues with the connection of power wires, sensor wires, and fan wires to the thermostat. The car blower's function is to direct the cold air from the air conditioning evaporator or the hot air from the heater core into the vehicle interior. Simply put, the blower serves to circulate air. Below is an introduction to the control principles of the blower: 1. Automatic Control: When the "Auto" switch on the air conditioning control panel is pressed, the air conditioning computer automatically adjusts the blower speed according to the required air temperature output. When the airflow direction is set to "Face" or "Bi-Level" and the blower is in low-speed mode, the blower speed will vary within a defined range based on the intensity of sunlight. 2. Low-Speed Control Operation: During low-speed control, the air conditioning computer cuts off the base voltage of the power transistor, which in turn disconnects the power transistor and the high-speed relay. Current flows from the blower motor to the blower resistor and then to ground, causing the motor to operate at low speed.
1
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.