What are the installation steps for the Tiida filter?

1 Answers
OAsher
07/30/25 5:25am
The installation steps for the Tiida filter are: 1. Remove the plastic film cover on the filter; 2. Keep the filter opening facing upwards to prevent oil spillage; 3. Use an oil filter wrench to cover the filter head and rotate to remove the filter; 4. Locate the filter installation position below the fuel tank; 5. Secure the filter with nuts. The function of the filter is to separate water from gasoline and filter out impurities. Taking the 2021 CVT Cool Edition Tiida as an example, its body dimensions are: length 4393mm, width 1766mm, height 1539mm, with a wheelbase of 2700mm.
Was this review help?
1
1
Share
More Forum Discussions

Can a Car Be Equipped with a Multifunction Steering Wheel?

Can a Car Be Equipped with a Multifunction Steering Wheel? The steps to install a multifunction steering wheel are as follows: 1. Use professional tools to remove the original steering wheel; 2. Use a screwdriver to remove the screws fixing the control levers for the headlights and wipers in the middle, then dismantle the upper and lower plastic covers and replace them with the new multifunction steering wheel; 3. Reconnect the electronic wiring to the corresponding positions, place the airbag in its designated position and secure it, then tighten the fixing screws on both sides of the steering wheel; 4. Code the new components to ensure the newly installed components function properly; 5. Use the vehicle diagnostic and maintenance information system to clear the vehicle's fault codes, ensuring successful coding, and perform a self-check on the vehicle's onboard computer.
13
0
Share

What are the pure electric vehicles from GAC Trumpchi?

GAC Trumpchi's currently available pure electric vehicles include: Trumpchi GE3, GAC ix4, and Qizhi EV. Among them, the Trumpchi GE3 and Qizhi EV are positioned as small SUVs, while the GAC ix4 is positioned as an entry-level compact SUV. Below are brief introductions of these models: 1. Trumpchi GE3: Features a floating roof design with slightly exaggerated pinwheel-style wheels. The rear of the car is also filled with 'triangular' elements, giving it a simple and playful look. In terms of dimensions, the car measures 4337/1825/1655mm in length/width/height with a wheelbase of 2560mm. Power-wise, the Trumpchi GE3 is driven by a pure electric system, with a motor outputting a maximum power of 163 horsepower (120kW) and peak torque of 290 N·m. It has a maximum range of over 310 km and accelerates from 0-100km/h in 9.3 seconds. 2. GAC ix4: Measures 4525mm/1852mm/1685mm in length/width/height with a wheelbase of 2640mm. The interior adopts the GS4's design, offering various wheel styles, front fog lights, and a sunroof depending on the model configuration. 3. Qizhi EV: The Qizhi EV is one of the few products in China built on a dedicated pure electric platform. It uses a new generation ternary lithium battery with an energy density of up to 160Wh/kg and a battery capacity of 54.75kWh. It consumes 14.7kWh per 100 km and has a comprehensive range of 410 km. Additionally, with its new-generation fast-charging technology, it can charge to 80% in 30 minutes and fully charge in 8 hours with AC slow charging, providing a 'powerful assist' for worry-free journeys.
10
2
Share

How to use the headlights of the Jetta VS5?

The method to use the headlights of the Jetta VS5 is: turn the lever on the left side of the steering wheel to activate the headlights. Rotating it one notch turns on the low beams, and rotating it two notches turns on the high beams. Taking the 2020 Jetta VS5 as an example, its body dimensions are: length 4419mm, width 1841mm, height 1616mm, with a wheelbase of 2630mm, a fuel tank capacity of 51 liters, and a trunk capacity of 482 liters. The 2020 Jetta VS5 features a front McPherson independent suspension and a rear multi-link independent suspension. It is equipped with a 1.4L inline 4-cylinder turbocharged engine, delivering a maximum horsepower of 150PS, a maximum power of 110kW, and a maximum torque of 250Nm, paired with a 6-speed automatic transmission.
20
4
Share

What is the method for checking the rearview mirror when changing lanes at night?

The method for checking the rearview mirror when changing lanes at night is: 1. First turn on the turn signal when changing lanes, then observe the rearview mirror; 2. If the rear vehicle is seen in the left rearview mirror in about one-fifth of the area at the left edge of the mirror, do not turn; 3. When the rear vehicle occupies one-third or half of the entire left rearview mirror and the whole vehicle can be seen, a safe turning operation can be performed. The method for adjusting the rearview mirror is: 1. Adjust the horizon image in the left rearview mirror to the center of the mirror; 2. Adjust the image of the left side of the vehicle to occupy one-quarter of the area on the right side of the mirror; 3. Adjust the horizon image in the right rearview mirror to two-thirds of the mirror's height; 4. Adjust the image of the right side of the vehicle to occupy one-quarter of the area on the left side of the mirror.
3
0
Share

What are the methods to remove carbon deposits from cars?

Methods to remove carbon deposits from cars are: 1. Add fuel additives when refueling; 2. Engine disassembly and cleaning; 3. Using a car drip cleaning system. Methods to prevent carbon deposits in cars include: 1. Turn off the engine 1 minute or 30 seconds after parking at the destination; 2. For manual transmission vehicles, increase the shift RPM. The impacts of increased carbon deposits in cars are: 1. Difficulty in starting; 2. Insufficient horsepower, unstable acceleration, and vibrations; 3. Air-fuel ratio imbalance; 4. Failure to meet emission standards; 5. Reduced combustion efficiency. The main components of car carbon deposits are: 1. Metal debris from engine friction and wear; 2. Dust from the air; 3. Viscous substances formed by the oxidation, thickening, and acidification of engine oil in high-temperature environments; 4. Paint film generated by the oxidation and concentration of lubricating oil.
3
1
Share

What is the solution for idle vibration in the 10th-generation Civic?

Introduction to the solution for idle vibration in the 10th-generation Civic: The most common cause of car vibration is a dirty throttle body or excessive carbon deposits in the fuel injectors. Additionally, the lower the temperature, the more fuel is required for a cold start, and the presence of carbon deposits can significantly affect the smoothness of the cold start. The solution is to clean the fuel system and check the idle control valve for carbon deposits, which should be cleaned if necessary. Below are the detailed explanations of related content: 1. Severe engine carbon deposits. The most common cause of car vibration is a dirty throttle body or excessive carbon deposits in the fuel injectors. When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold start injector can be largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts, making it difficult to start. In this situation, the car will only start easily once the carbon deposits have absorbed enough gasoline to become saturated. After starting, the gasoline adsorbed on the carbon deposits will be drawn into the combustion chamber by the engine's vacuum, causing the air-fuel mixture to become too rich. The engine's combustible mixture alternates between being too lean and too rich, leading to idle vibration after a cold start. 2. Ignition system issues. Check the condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or weak sparking from the spark plugs can also cause such issues. The solution is to check if the spark plugs have excessive carbon deposits and replace them if necessary. 3. Unstable fuel pressure. If you have already cleaned the engine carbon deposits, throttle body, replaced the gaskets, and spark plugs but still experience idle vibration, it is recommended to visit a 4S shop to check the fuel supply pressure and the intake pressure sensor. Abnormal fuel pump pressure or incorrect readings and poor performance of the intake pressure sensor can cause car vibration. The solution is to check the fuel pressure and replace components if necessary. 4. Aging engine components. Car vibration can also be related to worn engine mounts. Engine mounts are essentially the shock absorbers for the engine, responsible for absorbing minor vibrations during operation. If the engine mounts are faulty, these vibrations can be transmitted to the steering wheel and the cabin, causing idle vibration.
15
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.