What Are the Hidden Functions of the Baojun 560?

1 Answers
DiJulian
07/29/25 3:11pm
Baojun 560 key hidden functions include: quickly pressing the lock button twice in succession to trigger the car-finding function; door-not-closed reminder while driving; emergency start/stop function, etc. Triggering the car-finding function: Quickly press the lock button twice in succession to trigger the car-finding function. This will cause the Baojun 560's hazard lights to flash continuously for up to 20 times, making it highly visible in dark nights or crowded underground garages. Lock function trigger condition: If any door is not properly closed, pressing the lock button will result in 3 beeps and 3 flashes of the hazard lights to remind the owner that the door is not properly closed. Door-not-closed reminder: Door-not-closed reminder while driving, trigger condition: When any of the three doors other than the driver's door are not properly locked, the secondary lock on the driver's side cannot be engaged. Each time the secondary lock is pressed, it will immediately pop back to remind the owner that a door is not properly locked. Emergency start/stop function: Activation method: Press and hold the start button for 12 seconds to perform an emergency start. Additionally, for an emergency stop, press and hold the start button for 2 seconds or press it 3 times within 3 seconds to force the engine to stop.
Was this review help?
12
2
Share
More Forum Discussions

Why is the fuel consumption gauge fluctuating erratically?

Average fuel consumption is a calculated value used to display the fuel consumption over a certain distance traveled. During driving, significant changes in external air temperature or unstable engine coolant temperature can cause the computer to fluctuate greatly in calculating the fuel injection volume, leading to constant erratic fluctuations in the average fuel consumption gauge. Relevant information about fuel consumption is as follows: 1. Introduction: Fuel consumption generally refers to constant-speed fuel consumption, which is the vehicle's fuel consumption per 100 kilometers obtained in the constant-speed driving fuel consumption test specified by national standards for certain types of vehicles. 2. Testing method: The test can be conducted on the road or on a chassis dynamometer, and then the fuel consumption per 100 kilometers is calculated using the "flow meter method" or "carbon balance method."
15
3
Share

What are the effects of fuel pump pressure relief on a vehicle?

Under normal circumstances, the fuel pressure provided by the fuel pump is generally around 3-3.5 bars. The gasoline pressure may vary depending on the vehicle model. The function of the fuel pump is to draw gasoline from the fuel tank and deliver it through the pipelines and fuel filter to the carburetor float chamber. It is precisely because of the fuel pump that the fuel tank can be placed far from the engine, at the rear of the vehicle, and below the engine. If the fuel pump's pressure is insufficient, the following symptoms may occur: 1. A buzzing noise from the fuel pump under the rear seat while driving. 2. Weak acceleration, especially with noticeable hesitation during sudden acceleration. 3. Difficulty starting the vehicle, or failure to start. 4. The engine warning light on the instrument panel remains illuminated.
1
0
Share

How far can you drive when the fuel gauge is empty?

When the car's fuel gauge shows a remaining range of 0, it can still continue to drive for some distance. Around 50 kilometers, which provides sufficient mileage to find a gas station. Some vehicles may display a remaining range of 0 after the warning light comes on, but they can still run. The actual range is greatly influenced by driving habits and road conditions. Additional information: Fuel pump cooling: The fuel pump is cooled by gasoline, specifically the gasoline that passes through the fuel pump during operation, not by being fully submerged in gasoline. As long as the car can run normally and the fuel pump supplies fuel properly, it won't be damaged. The vehicle uses a fuel level sensor: to detect the remaining fuel in the tank. The specific principle involves a float on the fuel surface that detects the height of the fuel level and converts it into an electrical signal through a potentiometer.
11
1
Share

What are the symptoms of a faulty fuel pump control module?

When the fuel pump fails, the following symptoms may occur: weak acceleration with a jerking sensation during sudden acceleration; difficulty starting the engine; buzzing noises while driving; illumination of the engine warning light; and engine shaking or vibration. Causes of fuel pump failure include: poor fuel quality, where various impurities in the fuel tank are sucked into the fuel pump motor, causing damage; waiting until the fuel light comes on to refuel, which can lead to the fuel pump operating at a lower level without adequate cooling and lubrication; and failure to replace the fuel filter, which can cause severe blockage in the fuel supply system, making it difficult for the fuel pump to operate and leading to damage due to prolonged high-load conditions.
3
3
Share

What Are the Common Knowledge Points for Car Usage?

There are several key points to know about car usage: 1. Air conditioning usage: Car air conditioning mainly consists of three parts: air direction, fan speed, and temperature. 2. Use of recirculation mode: Recirculation mode means the air inside the car circulates without outside air. Use this mode when the outside air quality is poor or during summer. 3. Car wash precautions: Avoid rinsing a car that has been exposed to direct sunlight with cold water. In summer, the surface temperature of the car paint can become very high after prolonged exposure to sunlight. Washing the car at this time can cause the paint to contract suddenly due to the cold water, leading to damage. 4. Car tires: The typical lifespan of a car tire is three to five years. Even if the car is driven infrequently, tires should be replaced promptly after exceeding this period. 5. Dealing with a punctured tire: Always monitor tire pressure and avoid sudden acceleration or aggressive driving. If tire pressure is abnormal, find a safe place to replace the tire immediately.
15
4
Share

What is the normal pressure for a fuel pump pressure gauge?

Under normal circumstances, the fuel pressure provided by the fuel pump is generally around 3-3.5 bar. The gasoline pressure may vary depending on the vehicle model. The function of the fuel pump is to draw gasoline from the fuel tank and deliver it through the pipeline and fuel filter to the carburetor float chamber. It is precisely because of the fuel pump that the fuel tank can be placed at the rear of the vehicle, far from the engine and below the engine. According to the different driving methods, fuel pumps can be divided into two types: mechanically driven diaphragm type and electrically driven type. During operation, in addition to providing the fuel consumption required for engine operation, the fuel pump flow should also ensure sufficient return flow to maintain stable fuel system pressure and adequate cooling.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.