What are the hidden features of the Jetta VS7?

What Causes White Smoke from the Exhaust Pipe of a BMW 3 Series?

The reasons for white smoke from the exhaust pipe of a BMW 3 Series are: 1. The engine block temperature is too low, leading to poor fuel atomization during cold starts; 2. Poor-quality gasoline with excessive water content, accompanied by poor acceleration, though the coolant level remains normal; 3. Continuous white smoke accompanied by a drop in coolant level may indicate a burnt cylinder head gasket, allowing water from the cooling system to enter the combustion chamber—the cylinder head gasket should be replaced; 4. Incorrect valve and fuel injection timing. The BMW 3 Series is a mid-size car under the BMW brand. Taking the 2021 BMW 3 Series Facelift 320i Sport Edition as an example, it is powered by a 2.0L inline four-cylinder turbocharged engine with a maximum power of 115kW and a maximum torque of 250Nm, paired with an 8-speed automatic transmission, and features rear-wheel drive.

15

4

Share

Should You Press the Clutch When Shifting Gears in a Car?

When shifting gears in a car, it is necessary to press the clutch pedal, and you should press it all the way down. If the clutch is not fully depressed, the car may produce abnormal noises or even cause the clutch to vibrate. During the gear shifting process, if the clutch is not fully depressed, there will be a significant speed difference between the shifting gear set and the transmission gear set, making it difficult for them to mesh smoothly. In mild cases, this can accelerate wear and tear, while in severe cases, it can lead to gear grinding and damage to the transmission. The clutch functions like a switch, engaging or disengaging the power transmission. The clutch mechanism allows the driving part and the driven part to temporarily separate and gradually engage again. During the transmission process, relative rotation is also possible, meaning the driving and driven parts of the clutch cannot be rigidly connected. Every type of car has a clutch device, although the forms may vary.

5

1

Share

What brand is the Baojun 510 transmission?

The manufacturer of the Baojun 510 transmission is SAIC Motor Corporation Limited. SAIC Group's main businesses cover the R&D, production, and sales of complete vehicles (including passenger cars and commercial vehicles), components (including engines, transmissions, powertrains, chassis, interior and exterior trim, electronic and electrical components), as well as automotive service trade businesses such as logistics, vehicle information, used cars, and automotive financial services. The Baojun 510 transmission uses a 6-speed manual transmission or a CVT (simulated 8-speed) transmission. A manual transmission is a gear-shifting device used to alter the engine's speed and torque transmitted to the drive wheels, enabling the car to achieve different traction and speed under various conditions such as starting from a standstill, climbing hills, turning corners, and accelerating. For the daily use of the Baojun 510 transmission, the following points should be noted: Do not delay changing the transmission oil for an extended period. Prolonged failure to change the transmission oil can damage internal components such as bearings and the housing. Avoid coasting in neutral for long durations. While driving manual transmission models, many experienced drivers may coast in neutral, but for automatic transmission models, this can cause overheating and create a shock when shifting back into Drive (D). Never shift into Drive (D) or Reverse (R) before the vehicle has come to a complete stop. Many drivers, aiming for smooth operation, shift into reverse gear before the vehicle has fully stopped, which can significantly damage the transmission gears and, over time, lead to issues like gear grinding. Avoid frequently climbing steep slopes in Drive (D). On steep inclines, automatic transmission vehicles may overheat due to high load or shift prematurely, resulting in insufficient climbing power. In such cases, use manual mode to lock in lower gears or switch to sport mode to protect the transmission. Do not tow the vehicle over long distances. If an automatic transmission vehicle breaks down, use a flatbed tow truck to move the vehicle onto the tow platform while it is in Neutral (N). Do not use tow ropes or tow the vehicle directly.

15

2

Share

What to do when the OBD light comes on?

When the OBD light comes on, it indicates issues such as emissions not meeting standards, incomplete combustion, reduced power, and high fuel consumption. While you can continue driving, it is recommended that the owner repairs the vehicle as soon as possible. OBD, translated as On-Board Diagnostics in Chinese, is a system that continuously monitors the engine's operating conditions and the working status of the exhaust after-treatment system. It will immediately issue a warning if it detects any condition that may cause excessive emissions. When the ignition switch is turned on, the OBD indicator light will illuminate, initiating a system check, and it will turn off after the engine starts. If a fault affecting engine performance and emissions occurs while driving, the OBD light will illuminate. Possible causes include issues with the air filter or its connections, as well as fuel quality and weather conditions. Check if the air filter box is stuck, reinstall it, or try turning the engine off and restarting it.

18

3

Share

What Impact Will a Faulty Camshaft Position Sensor Cause?

The impacts caused by a faulty camshaft position sensor include: 1. After the camshaft position sensor fails, the ECU cannot detect changes in the camshaft's position, affecting the intake and exhaust system's air intake and exhaust volume, thereby impacting engine performance; 2. A faulty camshaft position sensor causes the computer to spray fuel disorderly, resulting in increased fuel consumption, misfires, and inability to reach higher RPMs; 3. The camshaft position sensor determines the ignition sequence. If it fails, it causes ignition issues, making the engine difficult to start. The function of the camshaft position sensor in a vehicle is to collect the position signal of the valve camshaft and input it to the ECU, enabling the ECU to identify the top dead center of cylinder 1 compression for sequential fuel injection control, ignition timing control, and knock control. The camshaft position sensor is a sensing device, also known as a synchronization signal sensor. It serves as a cylinder identification and positioning device, inputting the camshaft position signal to the ECU, and is the main control signal for ignition control.

8

1

Share

Is the Buick Excelle's Fuel Consumption High?

The comprehensive fuel consumption of the Buick Excelle is 5.3-5.9L/100km. Currently, there are four models of the 2021 Buick Excelle available for sale: the 1.3T automatic mild hybrid entry model and the 1.3T automatic mild hybrid elite model, both with a comprehensive fuel consumption of 5.3L/100km. The classic 1.5L automatic entry model and the classic 1.5L automatic elite model have a comprehensive fuel consumption of 5.9L/100km. The above figures are the NEDC comprehensive fuel consumption, which are the fuel consumption data measured under the NEDC test procedure. The actual fuel consumption is higher than this value, ranging from 6.9-7.5L/100km. When driving, the following five tips can help reduce fuel consumption: During the starting process, the vehicle should start in a low gear, gently press the accelerator, and gradually increase speed. Avoid suddenly pressing the accelerator hard, as this can multiply fuel consumption. Light acceleration and braking, early braking: When driving, gently press the accelerator to avoid sudden increases in engine speed and prevent the car from shaking during driving, thereby making the car more fuel-efficient. By estimating road conditions and adopting slow and uniform acceleration or braking, fuel economy can be increased by up to 20%. Maintain proper tire pressure: Keep the tire pressure at the level recommended by the manufacturer. For every 2 PSI below the recommended value (equivalent to about 0.2 in the metric system relative to the standard pressure of 2.4), fuel consumption increases by 1%. Regular vehicle maintenance or inspection: Timely oil changes can reduce carbon deposits (carbon deposits can cause ignition issues, sluggish acceleration, increased fuel consumption, and even cylinder misfires in severe cases); regularly check and replace the air filter if dirty, and clean or replace the fuel injectors, spark plugs, and throttle body as per mileage. Close the windows while driving. Driving with windows open increases wind resistance, which in turn increases the resistance the car faces, requiring more power and thus increasing fuel consumption.

6

5

Share

What are the hidden features of the Jetta VS7?

What Causes White Smoke from the Exhaust Pipe of a BMW 3 Series?

Should You Press the Clutch When Shifting Gears in a Car?

What brand is the Baojun 510 transmission?

What to do when the OBD light comes on?

What Impact Will a Faulty Camshaft Position Sensor Cause?

Is the Buick Excelle's Fuel Consumption High?

What to Do When a Vehicle Loses Throttle and Clutch While Driving?

Can private cars drive on highways at night?

What is the fuel consumption of the Changan CS75 1.5T?

What Are the Knowledge Points for Car Engine Repair?